Refrigeration and Air Conditioning Technology (MindTap Course List)
8th Edition
ISBN: 9781305578296
Author: John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 25, Problem 13RQ
Oil safety switch
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
If the main wire (coil) to the
distributor and the coil to the
switch are broken, replace them
and make sure the connections
are clean and tight relevant to
Ventilation system
Breaking system
Ignition system
Combustion system
Skip
Which of the following is the
fouled of spark plug
Soot
All of the above
Oil
Over heated
Skip
d. Check oil level & moisture content
19. If the main wire (coil) to the distributor and the coil to the switch are broken, replace them and make
sure the connections are clean and tight relevant to
a. Breaking system
b. Ignition system
c. Ventilation system
d. Combustion system
20. The required gap in ignition system between----------
a.-4 to 5
b.-0.4 to 5
c.-0.4 to 0.5
d.-4 to 0,5
|21. Which of the following is the fouled of spark plug
a. Soot
b. Oil
c. Over heated
d. All of the above
|22.The suitable thread of spark plug for heavy engine is
a. M19
b. M18
c. M15
d. M16
23. Using a Torque wrench, tighten the plugs to the specified torque. (Most) 4mm plugs are torqued to
four kilograms per square inch.
a. True
b. False
24. Start the engine and evaluate its performance refers to
a. Weekly Maintenance
b. Annually Maintenance
c. Daily Maintenance
d. None of them
25. Check to see if Dynamo is working properly. If necessary, adjust the regulator refers to
a. Weekly Maintenance
b. Annually…
Types of engine oil
Chapter 25 Solutions
Refrigeration and Air Conditioning Technology (MindTap Course List)
Ch. 25 - Which is not a basic component of the compression...Ch. 25 - Describe modulating fluid flow.Ch. 25 - The purpose of the crankcase pressure-regulating...Ch. 25 - Describe the function of an electric evaporator...Ch. 25 - Prob. 5RQCh. 25 - Briefly describe the function of a...Ch. 25 - Two types of relief valves are_______and ______.Ch. 25 - Why is low-ambient control necessary?Ch. 25 - Which is not a method of low-ambient control on...Ch. 25 - Low-pressure switch
Ch. 25 - High-pressure switchCh. 25 - Low-ambient(switch)Ch. 25 - Oil safety switchCh. 25 - What is the function of the current sensing relay...Ch. 25 - Why is there a time delay in an oil safety...Ch. 25 - What is off-cycle defrost?Ch. 25 - Two types of off-cycle defrost are______and...Ch. 25 - Two methods for accomplishing defrost on...Ch. 25 - Filter drierCh. 25 - Heat exchangerCh. 25 - Suction accumulatorCh. 25 - ReceiverCh. 25 - Prob. 23RQCh. 25 - Prob. 24RQCh. 25 - What will happen if the float in an oil separator...Ch. 25 - The function of the evaporator pressure regulator...Ch. 25 - What is the function of the oil return hole or...Ch. 25 - What is the function of the pressure equalization...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A 2 inch-diameter horizontal jet of water with a velocity of 20 ft/s relative to the ground strikes a flat plate that is attached to a car moving at a velocity of Ve. After it hits, the water splatters in all directions in the plane of the plate. Investigate the effect of the car velocity V. on the force exerted on the plate.arrow_forwardCooling system hoses should be replaced when they are. hard (brittle) soft (spongy) swollen all of the abovearrow_forwardA one-pipe system may be used when the oil tank is higher or lower than the oil pump. True or false.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningWelding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage LearningAutomotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
- Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
General Industrial Safety; Author: Jim Pytel;https://www.youtube.com/watch?v=RXtF_vQRebM;License: Standard youtube license