Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
6th Edition
ISBN: 9780135257272
Author: James D. Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 21, Problem 2CQ
To determine
State the purpose of the lower air dam in front of vehicles.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Which of the following statements about unibodyconstruction is not true?a. A unibody is a stressed hull structure in whicheach of the body parts supplies structural supportand strength to the entire vehicle.b. Unibody vehicles tend to be tightly constructedbecause the major parts are all welded together.c. All unibodies are constructed from steel.d. Most front-wheel-drive unibody vehicles have acradle or partial frame.
The CV joint boots on the left side of a vehicle appear to be squeezed together; the boots on the right side of the vehicle appear to be stretched apart.
Technician A says that one or more of the engine/transaxle's mounts may be broken.
Technician B says that one or more of the engine/transaxle's subframe mounts may be broken.
Who is correct?
O a. A only
O b.B only
C. Both A and B
O d. Neither A nor B
A technician is inspecting a vehicle and finds
the upper radiator hose is collapsed, and the
cooling system pulled into a vacuum when
cold. Technician A states that a leak in the
surge tank could be the cause. Technician B
states that the radiator cap is most likely
defective. Who is correct?
Select one:
a. Technician A only
b. Technician B only
c. Both Technicians A and B
d. Neither Technician A nor B
Chapter 21 Solutions
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Ch. 21 - What is normal operating coolant temperature?Ch. 21 - Explain the flow of coolant through the engine and...Ch. 21 - Why is a cooling system pressurized?Ch. 21 - Describe how to diagnose a heater problem.Ch. 21 - What are 10 common causes of overheating?Ch. 21 - What diagnostic trouble code (DTC) could be set if...Ch. 21 - Prob. 2CQCh. 21 - What type of pump is a water pump? a. Positive...Ch. 21 - Water pumps __________. a. only work at idle and...Ch. 21 - Which statement is true about thermostats? a. The...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which of the following statements about seat belt retractors is not true? They stow away the scat belts when they are not being used. They allow freedom of movement for the occupant of the seat. They can tighten up and pull the occupant back during a crash. On some vehicles, they work in concert with the air bag system.arrow_forwardBriefly describe the advantages of having a vehicle which is streamlined compared to a non-streamlined body.arrow_forwardTechnician A says that an air-conditioning system removes heat from inside the engine. Technician B says that the heating system removes heat from the inside of the vehicle. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
- Technician A says that you may be able to smell antifreeze from a leaking heater core. Technician B says that you may be able to hear a loose belt when the engine is running. Who is correct? Select one: a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardThe hydraulic system of the hydro-boost and Powermaster is being discussed: Technician A says that the hydro-boost uses a power-steering pump. Technician B says that the Powermaster uses an electric motor-driven vane pump. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardName the two most common problems that occur with power seats.arrow_forward
- Technician A uses sandpaper to remove carbon deposits from turbocharger wastegate parts. Technician B scrapes off heavy deposits before attempting to clean the unit. Who is correct?arrow_forwardWhile discussing working on hybrid vehicles: Technician A says to make sure that the high- voltage system is shut down and isolated from the vehicle before working near or with any high-voltage component. Technician B says that when working on or near the high-voltage system , even when it is de - powered , always use insulated tools. Who is correct ?arrow_forwardWhich of the following statements about engines is not true? The engine provides the rotating power to drive the wheels through the transmission and driving axle. Only gasoline engines are classified as internal combustion. The combustion chamber is the space between the top of the piston and the cylinder head. For the combustion in the cylinder to take place completely and efficiently, air and fuel must be combined in the right proportions.arrow_forward
- Technician A says that if the PCV valve or connecting hoses become clogged, excessive pressure will develop in the crankcase and can cause oil leaks. Technician B says that if the PCV valve or connecting hoses become clogged, oil may be pushed into the air cleaner or cause it to be drawn into the intake manifold. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardOne of the type of Tunnel washers is URE b GL Top transfer Forward tilt Side load Auto carte transferarrow_forwardWhich of the following would not cause noise while driving in 2WD under a heavy throttle? a. Faulty ignition switch b. Worn transfer case clutch c. Inoperative locking hubs d. Bad front half shaftarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,