Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 21, Problem 15RQ
Which of the following statements about oil gauge circuits is not true?
- A switch can be used
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
ödalg äbäi A negative gauge pressure is
referred as
Vacuum pressure
Suction pressure
Absolut pressure
None of theses O
Suction pressure and Vacuum
pressure
Name and sketch the three types of plug gauges
Choose correct answer:
In hydraulic system circuit,the pressure gauge would not be available in the power pack.
Select one:
True
False
Chapter 21 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 21 - True or False? A driver information center...Ch. 21 - What is the purpose of an IVR?Ch. 21 - Explain how an air-core gauge works.Ch. 21 - What are two ways to provide input for the...Ch. 21 - Describe the two types of instrument panel...Ch. 21 - What is the device found in some fuel tanks to...Ch. 21 - What is the correct way to check a coolant...Ch. 21 - What type of sending unit is typically used to...Ch. 21 - What is the major difference between an indicator...Ch. 21 - True or False? The ABS lamp turns on whenever the...
Ch. 21 - The indicator needle on a speedometer is held to...Ch. 21 - Which of the following uses a permanent magnet and...Ch. 21 - What type of memory is used to store the...Ch. 21 - Which of the following is not a true statement...Ch. 21 - Which of the following statements about oil gauge...Ch. 21 - While discussing what the maintenance reminders...Ch. 21 - None of the engines gauges works: Technician A...Ch. 21 - The oil pressure light stays on whenever the...Ch. 21 - A digital speedometer constantly reads 0 mph:...Ch. 21 - All gauges operate but read lower than normal:...Ch. 21 - When testing an engine temperature sensor:...Ch. 21 - The coolant temperature gauge stays low (cold)...Ch. 21 - While discussing the instrumentation on a Toyota...Ch. 21 - The TPM warning lamp is lit: Technician A says...Ch. 21 - The yellow electronic throttle control warning...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Before installing a gauge on the high-pressure side of a system, you should do which of the following? A. Turn on the system. B. Turn off the system. C. Adjust the system to a neutral position. D. Have a cylinder approved by the DOT nearby.arrow_forwardWhich of the following statements about manifold gauge sets is not true? An adapter is required for using R-12 gauges on an R-134a system. A manifold gauge set is used when discharging, charging, and evacuating and for diagnosing trouble in an A/C system. The gauge manifold is designed to control refrigerant flow. When the manifold test set is connected into the system, pressure is registered on both gauges at all times. R-134a service hoses have a black stripe along their length, the low-pressure hose is blue, and the high-pressure hose is red.arrow_forwardAll gauges operate but read lower than normal: Technician A says that the connection to the instrument cluster may be corroded. Technician B says that the cluster s IVR may be open. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- None of the engines gauges works: Technician A tests gauge operation using a scan tool. Technician B begins by checking the fuse and then checks for voltage at the last point common to all the malfunctioning gauges. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhat is thermocouple gauge used for detection of leaks in vacuum systems.arrow_forwardWhy should gauges be installed only after there is evidence that they are needed?arrow_forward
- Technician A says that many oil pressure sensors are typically variable resistors that change resistance based on pressure changes. Technician B says that a sensor substitution box can be used in place of the sensor while observing the reaction of the oil pressure gauge on the dash. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardOrifice meter can measure both gas and liquids. True Falsearrow_forwardWhich of the following statement is correct related to orifice meter. Orifice meter is a discharge measuring instrument Orifice meter is a Pressure head measuring instrument Orifice meter is a pressure measuring instrument Orifice meter is a velocity measuring instrumentarrow_forward
- When servicing an oil burner, a service technician must have a ______gauge and a _____ gauge.arrow_forwardWhile discussing the AWG system: Technician A says that most automotive wiring range from 0 to 4 gauge. Technician B says that the higher the gauge number, the larger the diameter of the wire. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardCheck the correct statements. * Attitude indicator must be adjusted during flight ASi must be adjusted when aircraft changes altitude Altimeter must be manually adjusted during flight The pressure inside the aneroid is kept at sea level when it comes to the altimeter Smaller aircraft normally use digital instruments smaller aircraft normally have several pitot tubes and static portsarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
- Electrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage LearningWelding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Mod-01 Lec-16 Basics of Instrumentation; Author: nptelhrd;https://www.youtube.com/watch?v=qbKnW42ZM5c;License: Standard YouTube License, CC-BY