Concept explainers
(a)
Length of pin extension in (a).
Answer to Problem 44A
Length of pin extension is
Explanation of Solution
Given:
The number of times the pin extension is
Concept used:
Relation between number of times pin extension is given as follows:
Here, number of times pin extension is
Calculation:
Substitute
Thus, Length of pin extension is
Conclusion:
Length of pin extension is
(b)
Length of pin extension in (b).
Answer to Problem 44A
Length of pin extension is
Explanation of Solution
Given:
The number of times the pin extension is
Calculation:
Substitute
Thus, Length of pin extension is
Conclusion:
Length of pin extension is
(c)
Diameter of the pin in (c).
Answer to Problem 44A
Diameter of the pin is
Explanation of Solution
Given:
The number of times the pin extension is
Calculation:
Substitute
Thus, Diameter of the pin is
Conclusion:
Diameter of the pin is
(d)
Diameter of the pin in (d).
Answer to Problem 44A
Diameter of the pin is
Explanation of Solution
Given:
The number of times the pin extension is
Calculation:
Substitute
Thus, Diameter of the pin is
Conclusion:
Diameter of the pin is
(e)
Length of pin extension in (e).
Answer to Problem 44A
Length of pin extension is
Explanation of Solution
Given:
The number of times the pin extension is
Concept used:
Relation between number of times pin extension is given as follows:
Here, number of times pin extension is
Calculation:
Substitute
Thus, Length of pin extension is
Conclusion:
Length of pin extension is
(f)
Diameter of the pin in (f).
Answer to Problem 44A
Diameter of the pin is
Explanation of Solution
Given:
The number of times the pin extension is
Calculation:
Substitute
Thus, Diameter of the pin is
Conclusion:
Diameter of the pin is
(g)
Length of pin extension in (g).
Answer to Problem 44A
Length of pin extension is
Explanation of Solution
Given:
The number of times the pin extension is
Concept used:
Relation between number of times pin extension is given as follows:
Here, number of times pin extension is
Calculation:
Substitute
Thus, Length of pin extension is
Conclusion:
Length of pin extension is
(h)
Length of pin extension in (h).
Answer to Problem 44A
Length of pin extension is
Explanation of Solution
Given:
The number of times the pin extension is
Concept used:
Relation between number of times pin extension is given as follows:
Here, number of times pin extension is
Calculation:
Substitute
Thus, Length of pin extension is
Conclusion:
Length of pin extension is
(i)
Diameter of the pin in (i).
Answer to Problem 44A
Diameter of the pin is
Explanation of Solution
Given:
The number of times the pin extension is
Calculation:
Substitute
Thus, Diameter of the pin is
Conclusion:
Diameter of the pin is
(j)
Length of pin extension in (j).
Answer to Problem 44A
Length of pin extension is
Explanation of Solution
Given:
The number of times the pin extension is
Concept used:
Relation between number of times pin extension is given as follows:
Here, number of times pin extension is
Calculation:
Substitute
Thus, Length of pin extension is
Conclusion:
Length of pin extension is
Want to see more full solutions like this?
Chapter 20 Solutions
Mathematics For Machine Technology
- A square bar 78 in. on a side is to be milled from a circular rod. If the available rods are 1 in., 114 in, and 112 in. and 2 in. in diameter, which rod should be used so there is the least waste? How much waste, in area, will there be with the selected rod? Round your answer to 2 decimal places.arrow_forwardAnalyze each of the following problems to determine whether the problem is a direct or inverse proportion and solve. Round the answers to 3 decimal places where necessary. a. A reamer tapers 0.0975 inch along a 3.2625-inch length. What is the amount of taper along a 2.1250-inch length? b. A machine produces 2550 parts in 8.5 hours. How many parts are produced by the machine in 10 hours? c. Of two gears that mesh, one gear with 12 teeth revolves at 420 rpm. What is the revolutions per minute of the other gear, which has 16 teeth?arrow_forwardA plug gage tapers 3.10 mm along a 38.00 mm length, as shown in Figure 215. Set up a proportion and determine the amount of taper in the workpiece for each of the following problems. Express the answers to 2 decimal places.arrow_forward
- Of two gears that mesh, the one that has the greater number of teeth is called the gear, and the one that has the fewer teeth is called the pinion (Figure 218). For each of the problems, set up a proportion, and determine the unknown value, x. Round the answers to 1 decimal place where necessary.arrow_forwardIn the following table, the diameters of spheres are given. Determine the volumes of the spheres. Round theanswers to 1 decimal place where necessary. V=D36 where V=volume , =3.14 , D=diameter 41.arrow_forwardIn the following table, the diameters of spheres are given. Determine the volumes of the spheres. Round the answers to 1 decimal place where necessary. V=D36 where V=volume , =3.14 , D=diameter 43.arrow_forward
- The volume V of a cone with height h and diameter d is given by V=0.2618d2h . What is the volume of a cone with diameter 72.4 cm and height 122.5 cm? Round the answer to 2 decimal places.arrow_forwardExpress these ratios in lowest fractional form. 4. 27mm:45mmarrow_forwardIn the following table, the diameters and heights of cones are given. Find the volumes of the cones. Round the answers to the nearest whole number. V=0.2618d2h where V=volume , d=diameter , h=height 53.arrow_forward
- Find each percentage. Round the answers to 2 decimal places when necessary. a. 15%of60 b. 3% of 42.3 c. 72.8% of 120 d. 0.7% of 812 e. 42.6% of 53.76 f. 130%of212 g. 1212 of32 h. 14 of 627.3arrow_forwardIn the following table, the radii and heights of cylinders are given. Determine the volumes of the cylinders. Round the answers to the nearest whole number. V=r2h where V=volume , =3.14 , r=radius , h=height 50.arrow_forwardReduce to its simplest form: a The ratio 12:20 b The rate 200miles8gallonsarrow_forward
- Mathematics For Machine TechnologyAdvanced MathISBN:9781337798310Author:Peterson, John.Publisher:Cengage Learning,Elementary Geometry For College Students, 7eGeometryISBN:9781337614085Author:Alexander, Daniel C.; Koeberlein, Geralyn M.Publisher:Cengage,Elementary Geometry for College StudentsGeometryISBN:9781285195698Author:Daniel C. Alexander, Geralyn M. KoeberleinPublisher:Cengage Learning