Structural Analysis, Si Edition (mindtap Course List)
6th Edition
ISBN: 9781337630948
Author: KASSIMALI, Aslam
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 2, Problem 4P
To determine
Find the axial load acting on column A, F, and H of the framing system.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
The floor of an apartment building, shown in Fig. P2.3, is subjected to a uniformly distributed load of 45 psf over its surface area. Determine the loads acting on the floor beams AF, BG, and CH, and the girders AC and FH, of the framing system.
Given. A two-story OCBF shown in Fig. 3.40c that forms part of the building
frame system in SDC E. The axial loads on the ground floor brace B1 are as follows:
Dead load D= 30 kips
Live load L= 15 kips
Seismic force QE = ±80 kips
Snow load S= 0 kips
Hydrostatic load H = 0
The redundancy coefficient p = 1.1.
Mapped two-second såpectral acceleration, Sps = 0.826 g.
Required. Determine a pipe section for brace B1, ASTM A53 Grade B steel; F, =
35 ksi, F = 60 ksi
16 ft
16 ft
Figure
-15 ft
B2
B1
--
-15 ft
B2
B1
Ordinary concentric brace frame (OCBF) example.
PROBLEMS
1002. A timber beam is reinforced with steel plates rigidly
attached at the top and bottom as shown in Fig. P-1002. By what
amount is the moment increased by the reinforcement if n = 15 and the
allowable stresses in the wood and steel are 8 MPa and 120 MPa,
respectively?
Ans. 52.2 kN-m
150
ma
w
10 mm
150
mm
250 mm
300 mm
10 mm
Chapter 2 Solutions
Structural Analysis, Si Edition (mindtap Course List)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- The roof of a single-story storage building, shown in Fig. P2.1, is subjected to a uniformly distributed load of 0.96 kPa over its surface area. Determine the loads acting on the floor beam BE and the girder AC of the framing systemarrow_forwardW W. W Mp 0.8 Mp Mp The above figure shows a continuous beam loaded with concentrated loads 'W' at the centre of each span. The value of 'W' at collapse will bearrow_forwardIn structural practice, steel clip angles are commonly used to transfer loads from horizontal girders to verticalcolumns. If the reaction of the girder upon the angle is a downward force of 45 kN as shown in Fig. 2-16 and iftwo 22-mm-diameter rivets resist this force, find the average shearing stress in each of the rivets. As in Problem2.5, assume that the rivet fills the hole.arrow_forward
- Find the maximum tensile and compressive flexure stresses for the cantilever beam shown in Fig. 10 kN 4 kN/m 6 m T INA 100 x 10 mm* N.A. 130 mm 200 mmarrow_forwardProblem 4. (9-10) The side girder shown in the photo supports the boạt and deck. An idealized model of this girder is shown in the figure, where it can be assumed A is a roller and B is a pin. Using a locale code, the anticipated deck loading transmitted to the girder is 6 kN/m. Wind exerts a resultant horizontal force of 4 kN as shown, and the mass of the boat that is supported by the girder is 23 Mg. The boat's mass center is at G. Determine the reactions at the supports. F1.60 m--1.80 m- -2 m- 6 kN/m 4 kN 0.30 m (a) 6 (3.80) = 22.8 kN 4 kN 0.30jm B, B -3.40m- -1.90m 10.10 m A, 23 (9.81) kN = 225.6 kN (b)arrow_forwardDetermine the resultant (magnitude, direction and location) of the line load acting on the beam shown in Fig. (a).arrow_forward
- The steel reinforced concrete slab shown in Fig. Q3 below has a 200mm thickness and is supported by 3 concrete beam girders at equal spacing of 9m. The deck is monolithically attached to the girders and has a total length of 20m and a width of 10m. It is reinforced with 15 x q16 steel bars across the length (19m length each bar) and 10 x p16 steel bars across the width (9m each bar). 3. 9 m Fig. Q3 (a) Assuming a nominal concrete unit weight of 25kN/m' and a steel unit weight of 78kN/m³, calculate the dead load G in kN. Consider only the deck selfweight and the selfweight of the steel reinforcement. Neglect the concrete beam girders. (b) The concrete deck carries a live load Q of 6kN/m Determine the total design load of the deck for the ultimate (ULS) and serviceability limit states (SLS) in kN (neglect the beam girders). (c) A steel column is 4m long and has a diameter of 0.50m. It is subjected to a compressive force of 20MN. Given that the, elastic modulus of the material is 210GPA,…arrow_forward1. Calculate the bar force in member AB due to REAL loads in kN.0 2. Calculate the bar force in member AF due to REAL loads in kN.0 3. Calculate the bar force in member BF due to REAL loads in kN.0 4. Calculate the bar force in member CD due to REAL loads in kN.0arrow_forwardProb. 1 Four 50 mm x 200 mm dressed planks are used to carry a super imposed load of "W" kN/m. The allowable bending stress of the plank is 8.30 MPa. How should the four planks be framed to give the maximum stiffness as a beam? Determine also the safe uniform "W" kN/m that this beam could carry if the span is 6 m and is assumed to be simply supported. diagram 1 40.5 40.5 40.5 40.5 162 diagram 2 134.25 268.5 187.50 187.50 40.5 187.5 40.5arrow_forward
- Two simply supported beams B, and Bz have spans l and 21 respectively. Beam B, has a cross-section of Ix1 units and beam b2 has a cross-section of 2 x 2 units. These beams are subjected to concentrated loads w each at the centre of their spans. The ratio of the maximum flexural stress in these beams is A. 4 B. 2 1 2 D. 4 C.arrow_forwardAn eight Storey city library is proposed to be constructed in Baguio. The structure shall be a reinforced concrete building (no shear walls). The weight per floor (including 1st floor) is estimated to be 1800 KN. The roof deck weighs 1700 KN. Solve for the Base Shear, V, for the condition above using the following formulas: 1. V =ZICKSW (SEAOC CODE 1974 - 4 TH Revision) Adopted by National Structural Code of the Philippines, 3rd edition (NSCP 1987) 2. V = ZICW/Rw National Structural Code of the Philippines, 4th edition (NSCP 1992), Volume I 3. Most critical formula for V as indicated in Sec. 208.5.2 of the NSCP Vol.1 5th edition (2001). 4. Most critical formula for V as indicated in the NSCP Vol.1 6th edition (2015). 1700 KN 100 KN 32 1800 KN La Tide Toeang Warg 32 1800 KN 32 259 32 1800 KN 32 1800 KN City Cam Cena, Nagun C Bengt Nearet Active failt Trace t Fae tunao Fa Segnet Nane Tut Fat Vear Maper 2012 Ma t et 10 00 32 1800 KN 3.5 20 Floor height: 1st floor 3.5m and the rest of the…arrow_forwarda- Calculate the ultimate shear force at point A of the continuous beam shown in Fig.3? 10% b-Calculate the number of bars of the compression reinforcement (As') in the doubly reinforced shown in Fig.2. Assume: Mu=480 kN.m, M2 = 300 kN.m, fy =400 N/mm², fe'- 25 N/mm², bar diameter 25 mm. 25% 03 (35%) S d-500 As. b-300 Id=64 As'arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you