Programmable Logic Controllers
5th Edition
ISBN: 9780073373843
Author: Frank D. Petruzella
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 2, Problem 3P
With reference to I/O module specifications:
- a. If the ON-delay time of a given discrete input module is specified as 12 ms, how much is this expressed in seconds?
- b. If the output leakage current of a discrete output module is specified as 950 μA, how much is this expressed in amperes?
- c. If the ambient temperature rating for an I/O module is specified as 60°C, how much is this expressed in degrees Fahrenheit?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
2. The process of adressing each input during one clock pulse is called
A Moore sequential circuit has three inputs (X2, X₁, and Xo) that specify a temperature range
in a room. The circuit has two outputs (I and D) that control a heater for the room; I = 1
causes the heater to increase its heat output, and D = 1 causes the heater to decrease its
heat output. If the temperature range is 0, 1, or 2 for three successive clock cycles, the
circuit generates I = 1, and conversely if the temperature range is 5, 6, or 7 for three
successive clock cycles, the circuit generates D = 1; otherwise, I = 0 and D = 0.
1. Draw a state diagram.
2. Construct a state table.
3. Using D flip-flops, construct a state assigned table.
4. Determine the next-state and output logic expressions.
5. Sketch the corresponding logic circuit.
Write a Verilog code with testbench for 16-bit up/down counter with
synchronous reset and synchronous up/down.
If up/down is set the counter is up counter and if it is not set, the
counter is a down counter.
clock
reset
Up/down
submit the module code, testbench code, and the simulation results.
Chapter 2 Solutions
Programmable Logic Controllers
Ch. 2 - Prob. 1RQCh. 2 - What is the function of a PLC output interface...Ch. 2 - Prob. 3RQCh. 2 - Prob. 4RQCh. 2 - Prob. 5RQCh. 2 - Prob. 6RQCh. 2 - Prob. 7RQCh. 2 - Prob. 8RQCh. 2 - Prob. 9RQCh. 2 - Prob. 10RQ
Ch. 2 - Prob. 11RQCh. 2 - What are the advantage and the disadvantage of...Ch. 2 - With reference to PLC discrete input modules: a....Ch. 2 - Prob. 14RQCh. 2 - Explain the function of the backplane of a PLC...Ch. 2 - Prob. 16RQCh. 2 - Prob. 17RQCh. 2 - Prob. 18RQCh. 2 - What electronic element can be used as the...Ch. 2 - With reference to discrete output module current...Ch. 2 - What electronic element can be used as the...Ch. 2 - Prob. 22RQCh. 2 - Prob. 23RQCh. 2 - Prob. 24RQCh. 2 - Prob. 25RQCh. 2 - Prob. 26RQCh. 2 - Prob. 27RQCh. 2 - Prob. 28RQCh. 2 - Prob. 29RQCh. 2 - Explain the difference between a unipolar and...Ch. 2 - Prob. 31RQCh. 2 - In what two ways can the loop power for current...Ch. 2 - Prob. 33RQCh. 2 - Prob. 34RQCh. 2 - Prob. 35RQCh. 2 - Write a short explanation for each of the...Ch. 2 - Write a short explanation for each of the...Ch. 2 - Prob. 38RQCh. 2 - Prob. 39RQCh. 2 - Prob. 40RQCh. 2 - Prob. 41RQCh. 2 - Prob. 42RQCh. 2 - Prob. 43RQCh. 2 - Prob. 44RQCh. 2 - Prob. 45RQCh. 2 - Prob. 46RQCh. 2 - Prob. 47RQCh. 2 - What information is normally stored in the ROM...Ch. 2 - Prob. 49RQCh. 2 - Prob. 50RQCh. 2 - Prob. 51RQCh. 2 - Prob. 52RQCh. 2 - Prob. 53RQCh. 2 - Prob. 54RQCh. 2 - Prob. 55RQCh. 2 - Prob. 56RQCh. 2 - Prob. 57RQCh. 2 - Prob. 58RQCh. 2 - Prob. 59RQCh. 2 - Prob. 60RQCh. 2 - What is the function of a transducer?Ch. 2 - Prob. 62RQCh. 2 - Prob. 1PCh. 2 - Assume a thermocouple, which supplies the input to...Ch. 2 - With reference to I/O module specifications: a. If...Ch. 2 - Prob. 4PCh. 2 - Prob. 5PCh. 2 - Prob. 6P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.Similar questions
- Q2: For the circuit shown in below, use (matlab, c++, or python) and Nodal Analysis to: a) Find the voltage across the current source 11 terminals b) Find the current through the resistance R1 c) Find the real and reactive Powers delivered by the current source 11 Find the real and reactive Powers consumed by the capacitor C2 d) 11 10 A RMS 50 Hz +35 Deg Z1 AM R2 402 Z4 R4 80 m Z2 L2 15 mH 12 7A RMS 50 Hz +74 Deg Zc1 C1 150 F R3 30 www w R6 40 Z6 L3 25 mH E1 100 V RMS - 40 Deg Z5 50 Hz www R5 20 Zc2 C2 200 Farrow_forwardWrite a Verilog code with testbench for 16-bit up/down counter with synchronous reset and synchronous up/down. If up/down is set the counter is up counter and if it is not set, the counter is a down counter. clock reset IIn/down submit the module code, testbench code, and the simulation results.arrow_forwardDescribe the clock generator in simple terms.arrow_forward
- Develop a logic circuit necessary to meet the following requirements: In a certain chemical-processing plant, a liquid chemical is used in a manufacturing process. The chemical is stored in three different tanks. A level sensor in each tanks produces a HIGH voltage when the level of chemical in the tank drops below a specified point. Design a circuit that monitors the chemical level in each tank and indicates when the level in any two of the tanks drops below the specified point. The design must include a chip with logic gates and also be written with VHDL code.arrow_forward2. Draw the timing diagram for the Clocked SR flip-flop at each of the instants t0 to t6 as described in the class meeting. a. at t0, Q is low, S is low, R is low b. at t0, Q is high, S is low, R is low Be sure to include the clock signal in the timing diagram.arrow_forwardDevelop a simple automated industrial temperature regulator system for operating the coolant relief valve in a high-temperature furnace. When the temperature exceeds the safety threshold value, this will set the sensor ON which is connected to the input port of a microcontroller. The relief valve itself is connected to the output of the microcontroller. The safety system should work as described below: 1. The temperature sensor is connected to Port B, bit 3 of the microcontroller 2. The relief valve is connected to Port A, bits 1 and 2 of the microcontroller 3. When the temperature in the furnace exceeds the threshold value, the sensor sets the input port B, bit 3 to ON. 4. When the sensor is ON, the microcontroller sends an appropriate output to Port A inorder to open the coolant relief valve. 5. As soon as the sensor goes to the OFF state, the microcontroller clears all the output port bits thus closing the relief valve. Q1. A flowchart can be used to describe the step-by-step plan…arrow_forward
- A taco generator is use as a sensor to detect the speed of a rotating motor. The o/p of the tacho is between Ov and 5v where the midrange (2.5v) is equivalent to that the motor is standstill. When motor accelerates CW toward full speed, the tacho o/p will vary from 2.5v to 5v and when the input of tacho varies from 2.5v down to Ov means the motor is accelerating towards cCW. The Scenario is to reflect the equivalent speed on two SSDS which one will read the equivalent speed of reading 5 for maximum Cw (5v) and the other will also read 5 for maximum CCW (Ov) equivalent speed in the reverse direction. Taco generator input is connected to PA4, the CW SSD on PORTB and the CCW SD on PORTC Write ATmega 16 program sketch to follow the above scenario REFS1 REFSO Voltage Reference Selection AREF, Internal Vref turned off AVCC with external capacitor at AREF pin 1 Reserved 1 Internal 2.56V Voltage Reference with external capacitor at AREF pin ADPS2 ADPS1 ADPSO Division Factor 2 1 1 1 1 16 1 32 1…arrow_forwardDesign a 9v DC oscillator circuit that produces a frequency of 500 Hz. The circuit may use a 555 timer or two transistor design(s). Show all calculations including the DC currents and bias voltages. Include the schematic and the required frequency formula(s). Do the best you can as the process to arrive at a final answer will be evaluated as well. From this, if a larger load were required to be connected to the chip, how would the schematic look and what components would be used to do design it? Also, as a theoretical approximation, if the 9v battery had a rating of 4 amp-hours, how long would it last powering this circuit? Show calculations to illustrate how you arrived at the answer. Remember, these questions are a reflection of your own work. Make sure any references used are cited.arrow_forwardDraw the circuit and obtain the truth table of the VHDL module below module SAM(a, b, c, M, S);input a,b,c;output M;output S;wire d,e,f;xor(S,a,b,c);and(d,~a,b);and(e,b,c);and(f,~a,c);or(M,d,e,f);endmodulearrow_forward
- Question 4: for the timing diagram below, synthesize the functionf (x1, x2, x3) in the simplest SOP form. X 1 1 X2 1 X3 Timearrow_forwardA PLC is used to control a single-axis robot, in which the axis is driven by a pneumatic cylinder. An output signal to the pneumatic cylinder causes it to extend (ON state). When there is no signal, the pneumatic cylinder retracts (OFF state). The gripper is an also driven by a pneumatic cylinder. The gripper open position is an OFF state and the closed position is an ON state. In order to perform a task, the following sequence of operations must be performed: TH Sequence No. Аxis Gripper OFF OFF 1 ON OFF ON ON 3 OFF ON 4 OFF OFF The process begins when the start bush button is ON and a part triggers a limit switch. For safety, an emergency switch is used to shut off the entire system. Design a PLC ladder diagram for this application.arrow_forwardDesign an up-down counter for 8085 to count from 0 to 9 and 9 to 0 continuously with a 1.5-second delay between each count, and display the count at one of the output ports. Draw a flowchart and show the delay calculations. Consider clock frequency of 1 MHzarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Database System ConceptsComputer ScienceISBN:9780078022159Author:Abraham Silberschatz Professor, Henry F. Korth, S. SudarshanPublisher:McGraw-Hill EducationStarting Out with Python (4th Edition)Computer ScienceISBN:9780134444321Author:Tony GaddisPublisher:PEARSONDigital Fundamentals (11th Edition)Computer ScienceISBN:9780132737968Author:Thomas L. FloydPublisher:PEARSON
- C How to Program (8th Edition)Computer ScienceISBN:9780133976892Author:Paul J. Deitel, Harvey DeitelPublisher:PEARSONDatabase Systems: Design, Implementation, & Manag...Computer ScienceISBN:9781337627900Author:Carlos Coronel, Steven MorrisPublisher:Cengage LearningProgrammable Logic ControllersComputer ScienceISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
Database System Concepts
Computer Science
ISBN:9780078022159
Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan
Publisher:McGraw-Hill Education
Starting Out with Python (4th Edition)
Computer Science
ISBN:9780134444321
Author:Tony Gaddis
Publisher:PEARSON
Digital Fundamentals (11th Edition)
Computer Science
ISBN:9780132737968
Author:Thomas L. Floyd
Publisher:PEARSON
C How to Program (8th Edition)
Computer Science
ISBN:9780133976892
Author:Paul J. Deitel, Harvey Deitel
Publisher:PEARSON
Database Systems: Design, Implementation, & Manag...
Computer Science
ISBN:9781337627900
Author:Carlos Coronel, Steven Morris
Publisher:Cengage Learning
Programmable Logic Controllers
Computer Science
ISBN:9780073373843
Author:Frank D. Petruzella
Publisher:McGraw-Hill Education
Electrical Measuring Instruments - Testing Equipment Electrical - Types of Electrical Meters; Author: Learning Engineering;https://www.youtube.com/watch?v=gkeJzRrwe5k;License: Standard YouTube License, CC-BY
01 - Instantaneous Power in AC Circuit Analysis (Electrical Engineering); Author: Math and Science;https://www.youtube.com/watch?v=If25y4Nhvw4;License: Standard YouTube License, CC-BY