Delmar's Standard Textbook Of Electricity
7th Edition
ISBN: 9781337900348
Author: Stephen L. Herman
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 19, Problem 1PA
You are changing the starting relay on a central air-conditioning unit when you notice that the identifying mark on the compressor-run capacitor is connected to the run winding of the compressor. Should you change the capacitor connection so that the identifying mark is facing the line side or is it correct as connected? Explain your answer.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
4-Why is the fall in the terminal voltage for the external chara. gereater
shunt generator than in separately - excited generator?
Question
6- Why it is possible to short circuit the differential
compound generator and not the cumulative
compound generator ?
The synchronous generator connected to the endless busbar is idle and synchronous.rotates at speed. If the voltage applied to the excitation winding is increased, how does the active and reactive power given by the synchronous generator to the network change? Please explain without numbers.
Chapter 19 Solutions
Delmar's Standard Textbook Of Electricity
Ch. 19 - 1. What is the dielectric?
Ch. 19 - List three factors that determine the capacitance...Ch. 19 - A capacitor uses air as a dielectric and has a...Ch. 19 - 4. In what form is the energy of a capacitor...Ch. 19 - Four capacitors having values of 20 F, 50 F, 40 F,...Ch. 19 - f the four capacitors in Question 5 were to be...Ch. 19 - A 22-F capacitor is connected in series with a...Ch. 19 - 8. A 450-pF capacitor has a total charge time of...Ch. 19 - Can a nonpolarized capacitor be connected to a DC...Ch. 19 - Explain how an AC electrolytic capacitor is...
Ch. 19 - What type of electrolytic capacitor will be...Ch. 19 - A 500-nF capacitor is connected to a 300-k...Ch. 19 - A film-type capacitor is marked 253 H. What are...Ch. 19 - A postage stamp mica capacitor has the following...Ch. 19 - A postage stamp capacitor has the following color...Ch. 19 - You are changing the starting relay on a central...Ch. 19 - You are an electrician working in an industrial...Ch. 19 - You find that a 25-F capacitor connected to 480...Ch. 19 - Fill in all the missing values. Refer to the...Ch. 19 - Two capacitors having values of 80 F and 60 F are...Ch. 19 - Three capacitors having values of 120 F, 20 F, and...Ch. 19 - Three capacitors having values of 2.2 F, 280 F,...Ch. 19 - A 470-F capacitor is connected in series with a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- How to adjust reactive power in synchronous machine? A) by changing the load applied to the shaft B) by changing the frequency C) by changing the excitation current D) by changing the applied voltagearrow_forwardWhich one not related to Synchronous Generator a.Commutator b.Rotate field c.Damper Winding d.Non Salient polearrow_forwardIN Counter-Current Breaking o f a 3-Phase Induction Motor(Reversing the Operation o f a 3-Phase Induction Motor) How it was insured in the control circuit as to avoid the operation of both positiveand negative sequences simultaneously?arrow_forward
- c) What is the physical meaning for each of the following induction motor parameters: R1 „R2 ,Rc ,X1 ,X2 ,Xm ? What is synchronous watt?arrow_forwardHow does grid synchronization work in a multi-generator power system?arrow_forwardconds. v Question Completion Status: A Moving to another question will save this response. uestion 2 Which of the following is essential condition of paralleling two DC generators? Equal currents Equal rating Correct polarity O Equal output aarrow_forward
- Calculate the reactance voltage for a machine which runs at 900rpm number of commutator segments is 65, brush width is 1.74 (in commutator segments), coefficient of self induction is 153 the conductor current is 27A.arrow_forwardQ1) Answer the following: - 1-E = (V – laRa ) then N = 2-The consist of and N 3-In a the shunt field winding is connected in parallel with the armature winding only. Series Field Shunt Field R Re 4- The Vo is adjusted by adding This increase slope of this line causing the operating point to shift at lower voltage. No Load V prime mover certain speed. 5-for wave wound generator A= , and for lap wound generator A= 6-The is made up of insulated 7- The connection arrangement to obtain shunt or series excited generators, the field winding is disconnected from the machine and connected across an external supply. is as shown in the figure below. For UC No Supply Load field winding constant speed wwwarrow_forwardThe reactance’s of the alternator during the periods of the subtransient, transient and steady state periods are following, Leakage reactance(XL)=0.13 ohm, Damper winding reactance(XD)= 0.27 ohm Field winding reactance(Xf)=0.54 ohm and Armature reactance (Xm)= 0.73 ohm. The value of the transient reactance during the transient conditions is Transient Reactancearrow_forward
- Explain how the following adjustments are made in a single phase induction type energy meter: (a) Lag adjustment (b) Adjustment for friction compensation (c) Creep (d) Overload compensation (e) Temperature compensationarrow_forward1. A) What is a compound DC generator? a) a generator which utilizes a shunt or a series field b) a generator which utilizes both a shunt and a series field c) a generator which utilizes both separate and self excitation d) none of the above B) What is a cumulative-compound generator? a) a generator where the series and shunt fields work together in the same direction b) a generator where the series and shunt fields work against each other c) a generator where the series and shunt fields are not energize at the same time d) none of the abovearrow_forwardK-a. The phase angle difference between the currents in the start winding and run winding of a single-phase split-phase motor is typically 90 degrees. a) true b) false K-b. A centrifugal switch is used to disconnect the______ winding of a non-hermetically sealed single-phase split-phase motor at approximately 75% of rated speed. a) run b) start c) either "a" or "b" d) neither "a" nor "b" K-c Where an internal centrifugal switch cannot be used, an external_____ relay can be used to perform the same function in a single-phase split-phase motor. a) hot-wire b) current c) solid-state starting d) all of the abovearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Electricity for Refrigeration, Heating, and Air C...Mechanical EngineeringISBN:9781337399128Author:Russell E. SmithPublisher:Cengage Learning
Electricity for Refrigeration, Heating, and Air C...
Mechanical Engineering
ISBN:9781337399128
Author:Russell E. Smith
Publisher:Cengage Learning
FMPR-103 pt1 l Power Systems Protection v1; Author: L&D for Protection and Control;https://www.youtube.com/watch?v=ELWncjsh5uE;License: Standard Youtube License