Thermodynamics: An Engineering Approach
9th Edition
ISBN: 9781259822674
Author: Yunus A. Cengel Dr., Michael A. Boles
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 17.7, Problem 47P
To determine
What will happen when a diverging section is added to supersonic flow in a duct.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Air flows through an Otto Cycle, beginning the compression process at a temperature of 50 °C.
The volume of gas present in the cylinder at the start of compression is 0.001 m³. During the heat
addition process, 1200 kJ/kg of heat is added to the air. The compression ratio of the cycle is 8.5.
Using cold-air standard analysis;
Calculate the temperatures at the other states in the cycle
Write the equation and sample to determine the mass,
Write the equation and sample to determine the net work,
Write the equation and sample to determine the thermal efficiency,
Write the equation and sample to determine the volume at the end of the compression,
Write the equation or sample to determine the Mean effective pressure, and
Plot the work produced during one cycle, the maximum pressure in the cycle, the thermal
efficiency of the cycle, and the mean effective pressure for pressures at the beginning of
compression ranging between 50 kPa and 150 kPa, assuming that the air behaves as an ideal gas…
How to calculate the static pressure and the stagnation pressure?
30. The entering air of a diffuser in a jet engine with a velocity of 1850 ft/sec relative to the aircraft. The intake pressure is 1.05 psia and intake temperature is -60oF. Assuming isentropic compression in the diffuser, calculate the inlet Mach numberA. 1.886 B. 1.786 C. 1.686 D. 1.586
Chapter 17 Solutions
Thermodynamics: An Engineering Approach
Ch. 17.7 - A high-speed aircraft is cruising in still air....Ch. 17.7 - What is dynamic temperature?Ch. 17.7 - Prob. 3PCh. 17.7 - Prob. 4PCh. 17.7 - Prob. 5PCh. 17.7 - Prob. 6PCh. 17.7 - Calculate the stagnation temperature and pressure...Ch. 17.7 - Prob. 8PCh. 17.7 - Prob. 9PCh. 17.7 - Prob. 10P
Ch. 17.7 - Prob. 11PCh. 17.7 - Prob. 12PCh. 17.7 - Prob. 13PCh. 17.7 - Prob. 14PCh. 17.7 - Prob. 15PCh. 17.7 - Prob. 16PCh. 17.7 - Prob. 17PCh. 17.7 - Prob. 18PCh. 17.7 - Prob. 19PCh. 17.7 - Prob. 20PCh. 17.7 - Prob. 21PCh. 17.7 - Prob. 22PCh. 17.7 - Prob. 23PCh. 17.7 - Prob. 24PCh. 17.7 - Prob. 25PCh. 17.7 - Prob. 26PCh. 17.7 - The isentropic process for an ideal gas is...Ch. 17.7 - Is it possible to accelerate a gas to a supersonic...Ch. 17.7 - Prob. 29PCh. 17.7 - Prob. 30PCh. 17.7 - A gas initially at a supersonic velocity enters an...Ch. 17.7 - Prob. 32PCh. 17.7 - Prob. 33PCh. 17.7 - Prob. 34PCh. 17.7 - Prob. 35PCh. 17.7 - Prob. 36PCh. 17.7 - Prob. 37PCh. 17.7 - Air at 25 psia, 320F, and Mach number Ma = 0.7...Ch. 17.7 - Prob. 39PCh. 17.7 - Prob. 40PCh. 17.7 - Prob. 41PCh. 17.7 - Prob. 42PCh. 17.7 - Prob. 43PCh. 17.7 - Is it possible to accelerate a fluid to supersonic...Ch. 17.7 - Prob. 45PCh. 17.7 - Prob. 46PCh. 17.7 - Prob. 47PCh. 17.7 - Consider subsonic flow in a converging nozzle with...Ch. 17.7 - Consider a converging nozzle and a...Ch. 17.7 - Prob. 50PCh. 17.7 - Prob. 51PCh. 17.7 - Prob. 52PCh. 17.7 - Prob. 53PCh. 17.7 - Prob. 54PCh. 17.7 - Prob. 57PCh. 17.7 - Prob. 58PCh. 17.7 - Prob. 59PCh. 17.7 - Prob. 60PCh. 17.7 - Prob. 61PCh. 17.7 - Air enters a nozzle at 0.5 MPa, 420 K, and a...Ch. 17.7 - Prob. 63PCh. 17.7 - Are the isentropic relations of ideal gases...Ch. 17.7 - What do the states on the Fanno line and the...Ch. 17.7 - It is claimed that an oblique shock can be...Ch. 17.7 - Prob. 69PCh. 17.7 - Prob. 70PCh. 17.7 - For an oblique shock to occur, does the upstream...Ch. 17.7 - Prob. 72PCh. 17.7 - Prob. 73PCh. 17.7 - Prob. 74PCh. 17.7 - Prob. 75PCh. 17.7 - Prob. 76PCh. 17.7 - Prob. 77PCh. 17.7 - Prob. 78PCh. 17.7 - Prob. 79PCh. 17.7 - Air flowing steadily in a nozzle experiences a...Ch. 17.7 - Air enters a convergingdiverging nozzle of a...Ch. 17.7 - Prob. 84PCh. 17.7 - Prob. 85PCh. 17.7 - Consider the supersonic flow of air at upstream...Ch. 17.7 - Prob. 87PCh. 17.7 - Prob. 88PCh. 17.7 - Air flowing at 40 kPa, 210 K, and a Mach number of...Ch. 17.7 - Prob. 90PCh. 17.7 - Prob. 91PCh. 17.7 - Prob. 92PCh. 17.7 - What is the characteristic aspect of Rayleigh...Ch. 17.7 - Prob. 94PCh. 17.7 - Prob. 95PCh. 17.7 - What is the effect of heat gain and heat loss on...Ch. 17.7 - Consider subsonic Rayleigh flow of air with a Mach...Ch. 17.7 - Prob. 98PCh. 17.7 - Prob. 99PCh. 17.7 - Air is heated as it flows subsonically through a...Ch. 17.7 - Prob. 101PCh. 17.7 - Prob. 102PCh. 17.7 - Prob. 103PCh. 17.7 - Air enters a rectangular duct at T1 = 300 K, P1 =...Ch. 17.7 - Prob. 106PCh. 17.7 - Prob. 107PCh. 17.7 - Air is heated as it flows through a 6 in 6 in...Ch. 17.7 - What is supersaturation? Under what conditions...Ch. 17.7 - Steam enters a converging nozzle at 5.0 MPa and...Ch. 17.7 - Steam enters a convergingdiverging nozzle at 1 MPa...Ch. 17.7 - Prob. 112PCh. 17.7 - Prob. 113RPCh. 17.7 - Prob. 114RPCh. 17.7 - Prob. 115RPCh. 17.7 - Prob. 116RPCh. 17.7 - Prob. 118RPCh. 17.7 - Prob. 119RPCh. 17.7 - Using Eqs. 174, 1713, and 1714, verify that for...Ch. 17.7 - Prob. 121RPCh. 17.7 - Prob. 122RPCh. 17.7 - Prob. 123RPCh. 17.7 - Prob. 124RPCh. 17.7 - Prob. 125RPCh. 17.7 - Prob. 126RPCh. 17.7 - Nitrogen enters a convergingdiverging nozzle at...Ch. 17.7 - An aircraft flies with a Mach number Ma1 = 0.9 at...Ch. 17.7 - Prob. 129RPCh. 17.7 - Helium expands in a nozzle from 220 psia, 740 R,...Ch. 17.7 - Helium expands in a nozzle from 0.8 MPa, 500 K,...Ch. 17.7 - Air is heated as it flows subsonically through a...Ch. 17.7 - Air is heated as it flows subsonically through a...Ch. 17.7 - Prob. 134RPCh. 17.7 - Prob. 135RPCh. 17.7 - Air is cooled as it flows through a 30-cm-diameter...Ch. 17.7 - Saturated steam enters a convergingdiverging...Ch. 17.7 - Prob. 138RPCh. 17.7 - Prob. 145FEPCh. 17.7 - Prob. 146FEPCh. 17.7 - Prob. 147FEPCh. 17.7 - Prob. 148FEPCh. 17.7 - Prob. 149FEPCh. 17.7 - Prob. 150FEPCh. 17.7 - Prob. 151FEPCh. 17.7 - Prob. 152FEPCh. 17.7 - Consider gas flow through a convergingdiverging...Ch. 17.7 - Combustion gases with k = 1.33 enter a converging...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Air with a pressure of 0.1 MPa and a temperature of 25oC with a flow rate of 5.29 kg/minute enters a three-stage reciprocating piston compressor with intercooler. The air is compressed polytropically (n = 1.3) to reach the pressure of 4 MPa. Calculate: a) The pressure at stage-2 and stage-3 so that the compression work is minimum? b) The compression work in each stage and the total compression work? c) The outlet air temperature from each stage's cylinder? d) The amount of heat transferred to each intercooler? e) How much air is needed for cooling in the intercooler if the allowable maximum temperature changes between the inlet and outlet of the intercooler is 8oC?arrow_forward- Q4// An open gas turbine plant works between the fixed absolute temperature limits 300K and 1500K, thẻ absolute pressure limits being 1bar and 14bar. The isentropic efficiency of compresso" is 0.85 and that of turbine is 0.86. Estimate the actual thermal efficiency of the plant and the power developed. The calorific value of fuel is 4200kJ/kg. Assume neombustor 0.99, Nmech=0.98 for whole assembly, ngen=0.985, and air mass flow rate is 500kg/s. [Hint: (m. + m,)h, - mahz = m, x C.V.x Ncombustor]arrow_forwardQuestion 4 The air compressor in the core of the CFM56-5A1 turbofan engine of the Airbus A320 compressors 50 kg/s of air at 5°C and 0.8bar to 30bar. The compressor has an isentropic efficiency of 85%. Calculate the isentropic and actual temperature at exit from the compressor. You can assume for air that y=1.4 cp = 1005 J/kg K You can assume for isentropic compression. P₂ P₁ T₁ Compressor Isentropic efficiency is n = T25 -11 7₂-41 Where T₁ is the temperature at the start of compression in Kelvin and T₂ is the temperature at the end of compression in Kelvin. The subscripts is for temperature at the end of isentropic compression. =arrow_forward
- c) Can a turbine rotation really reach supersonic speed? What is the usual cut-out speed for wind turbines (cut-out speed is the speed of air at which the turbine would shut down)?arrow_forwardA four stage single acting air compressor running in an atmospheric at 87 KPa and 15 degrees Celsius has a free air delivery of 2,83 m³/min. The section pressure and temperature are 80 KPa and 32 degrees Celsius respectively, the delivery pressure is to be 7 MPa. The temperature at the start of compression in each stage is 32 degrees Celsius, take n=1,3 for all stages. Calculate 1.the mass flow rate to 3 decimal place in kg/min 2. The power input in KW to 1 decimal placearrow_forwardThe cycle with a pressure compression ratio of 8.60. The isentropic compression of air has an initial temperature of 54 degrees fahrenheit. Find the final temperature that is estimated to the nearest degrees fahrenheit. kair = 1.4 and the specific heat is constant.arrow_forward
- Assess the different types of industrial compressor and identify justifiable applications for each while focusing on the working principle and flow directionarrow_forwardPlease explain What is Reversible Isothermal Compression?arrow_forwardQUESTION 3 A high-pressure axial compressor for a stagnation pressure ratio of 8.5. The mass flow rate of air through the compressor is 16 kg/s and the stagnation conditions at inlet are 200 kPa and 450 K. The polytropic efficiency is 91 %. jet engine rotates at 15,000 rpm with and overall (a) If the mean radius is 0.24 m and this is constant throughout the compressor, calculate the total-to-total isentropic efficiency of the compressor and show that, for the stage loading to be less than 0.4 in all stages, eight stages required. are (b) The compressor is designed with repeating stages and zero inlet swirl. If the inlet axial Mach number is 0.52, calculate the mean flow coefficient and sketch the velocity triangles for one stage. Show that the blade height at exit from the compressor is about 7.8 mm.arrow_forward
- In an ammonia refrigerator , the pressure in the evaporator is 267. 58 KPa and the ammonia at is 0.14 dry while at the exit is 0.86 dry . During compression the work done per kg of ammonia is 20 ,000 kg .m . Calculate volume of the vapor entering the compressor per minute if the rate of ammonia circulation is 6.54 kg. The compressor has a volumetric efficiency of 90% and it runs at 150 rpm .The ratio of stroke to bore is 1 .Latent enthalpy of ammonia at based on its evaporating pressure is 320 Kcal per kg and its latent specific volume of ammonia based on its evaporating pressure is 0.436 m3 per kg .Specific volume of ammonia WITH PH DIAGRAMarrow_forwardQuestion 1 A single stage reciprocating compressor takes 1m³ of air per minute and 1.013 bar and 15°C and delivers at 7 bar. Assuming Adiabatic law (n=1.35) and no clearance. Calculate: 1.1. Mass flow rate (1.226 kg/min) 1.2. Delivery Temperature (475.4 K) 1.3. Indicated power (4.238 kW)arrow_forwardConsider a cylinder of a gasoline engine at the beginning of the compression cycle, duringwhich a fuel/air mixture (for our purposes mostly composed of nitrogen and oxygen, i.e.an ideal gas of diatomic molecules) at 300 K and 1 bar is compressed down to one-tenthvolume (compression ratio of 10:1). Assume that the compression is rapid so no heatexchange occurs with the environment. Calculate the pressure and the temperature ofthe compressed gas. In a diesel engine, the compression ratios are typically much higher;redo the same calculation with a compression ratio of 20:1.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License