VECTOR MECH...,STAT.+DYN.(LL)-W/ACCESS
VECTOR MECH...,STAT.+DYN.(LL)-W/ACCESS
12th Edition
ISBN: 9781260265453
Author: BEER
Publisher: MCG
bartleby

Concept explainers

bartleby

Videos

Question
Book Icon
Chapter 17.2, Problem 17.88P
To determine

Find the speed of the rod relative to the tube when x=400mm.

Expert Solution & Answer
Check Mark

Answer to Problem 17.88P

The speed of the rod relative to the tube when x=400mm is 2.51m/s_.

Explanation of Solution

Given information:

The mass (mR) of the rod AB is 4 kg.

The mass (mT) of the tube CD is 6 kg.

The angular velocity (ω) of the assembly is 5 rad/s.

Calculation:

Consider l is the length of the rod and the tube and O is the point of intersection of the tube and axle.

Write the equation of the centroidal mass moment of inertia (I¯T) of the tube.

I¯T=112mTl2

Write the equation of the centroidal mass moment of inertia (I¯R) of the rod.

I¯R=112mRl2

Write the equation of the tangential equation of the tube using kinematics.

(v¯θ)T=r¯Tω

Substitute l2 for r¯T.

(v¯θ)T=l2ω

Write the equation of the tangential equation of the rod using kinematics.

(v¯θ)R=r¯Rω

Substitute l2+x for r¯R.

(v¯θ)R=(l2+x)ω

Find the equation of angular momentum about point O.

HO=mTr¯T(v¯θ)T+I¯Tω+mRr¯R(v¯θ)R+I¯Rω

Substitute l2 for r¯T, l2ω for (v¯θ)T, 112mTl2 for I¯T, l2+x for r¯R, (l2+x)ω for (v¯θ)R, and 112mRl2 for I¯R.

HO=mTl2(l2ω)+112mTl2ω+mR(l2+x)(l2+x)ω+112mRl2ω=412mTl2ω+mR(l24+2l2x+x2+112l2)ω=13mTl2ω+mR(4l212+lx+x2)ω=[13mTl2+mR(13l2+lx+x2)]ω (1)

Find the equation of kinetic energy.

T=12mT(v¯θ)T2+12I¯Tω2+12mR(v¯θ)R2+12mRvr2+12I¯Rω2

Substitute l2ω for (v¯θ)T, 112mTl2 for I¯T, (l2+x)ω for (v¯θ)R, and 112mRl2 for I¯R.

T=12mT(l2ω)2+12(112mTl2)ω2+12mR(l2+x)2ω2+12mRvr2+12(112mRl2)ω2=12[mTl24ω2+112mTl2ω2+mR(l24+lx+x2)ω2+112mRl2ω2]+12mRvr2=12[13mTl2+mR(13l2+lx+x2)]ω2+12mRvr2 (2)

Substitute Equation (1) in Equation (2),

T=12HOω+12mRvr2 (3)

All the motion in the system is horizontal. Therefore, the potential energy is zero.

Consider the initial position. (x=0).

At the initial position, the initial angular velocity of the system is 5 rad/s and the radial velocity is zero.(ω=ω1=5rad/sandvr=0).

Find the angular momentum at the initial position using equation (1).

(HO)1=[13mTl2+mR(13l2+lx+x2)]ω1

Substitute 0 for x.

(HO)1={13mTl2+mR[13l2+l(0)+(0)2]}ω1=(13mTl2+13mRl2)ω1=13(mT+mR)l2ω1

Substitute 6 kg for mT, 4 kg for mR, 0.8 m for l, and 5 rad/s for ω1.

(HO)1=13(6+4)(0.8)2(5)=10.6667kgm2/s

Find the kinetic energy at initial position using equation (3).

T1=12(HO)1ω1+12mRvr2

Substitute 10.6667kgm2/s for HO, 5 rad/s for ω1, and 0 for vr.

T1=12(10.6667)(5)+12mR(0)2=26.6667J

Consider the final position. (x=0.4m).

Find the angular momentum at the final position using equation (1).

(HO)2=[13mTl2+mR(13l2+lx+x2)]ω1

Substitute 0.4 m for x.

(HO)2={13mTl2+mR[13l2+lx+x2]}ω2

Substitute 6 kg for mT, 0.8 m for l, 4 kg for mR, and 0.4 m for x.

(HO)2={13(6)(0.8)2+4[13(0.8)2+(0.8)(0.4)+(0.4)2]}ω2=4.0533ω2

Find the kinetic energy at final position using equation (3).

T2=12(HO)2ω2+12mRvr2

Substitute 4.0533ω2 for (HO)2 and 4 kg for mR.

T2=12(4.0533ω2)ω2+12(4)vr2=2.02665ω22+2vr2

Consider the conservation of angular momentum.

(HO)1=(HO)2

Substitute 10.6667kgm2/s for (HO)1 and 4.0533ω2 for (HO)2.

10.6667=4.0533ω2ω2=2.6316rad/s

Find the speed of the rod relative to the tube when x=400mm.

Consider the conservation of energy.

T1+V1=T2+V2

Substitute 26.6667J for T1, 0 for V1, 2.02665ω22+2vr2 for T2, and 0 for V2.

26.6667+0=2.02665ω22+2vr2+02.02665ω22+2vr2=26.6667

Substitute 2.6316rad/s for ω2.

2.02665(2.6316)2+2vr2=26.6667vr=2.51m/s

Thus, the speed of the rod relative to the tube when x=400mm is 2.51m/s_.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
0.54 m -1.08 m- Fig. P16.61 Fig. P16.60 16.62 Two uniform cylinders, each of mass 7 kg and radius r= 125 mm. are connected by a belt as shown. If the system is released from rest. determine (a) the angular acceleration of each cylinder, (b) the tension in the portion of belt connecting the two cylinders, (c) the velocity of the center of the cylinder A after it has moved through I m. Fig. P16.62
The 10-in.-radius brake drum is attached to a larger flywheel which is not shown. The total mass moment of inertia of the flywheel and drum is 22 lb ⋅ ft ⋅ s 2 and the coefficient of kinetic friction between the drum and the brake shoe is 0.41. Knowing that the initial angular velocity is 255 rpm clockwise, determine the force which must be exerted by the hydraulic cylinder at point B if the system is to stop in 85 revolutions.
The double pulley shown has a weight of 35.0 lb and a centroidal radius of gyration of 5.0 in. Cylinder A (25.0 lb) and block B (16 lb) are attached to cords that wrap around pulleys in the manner shown. The coefficient of kinetic friction between block B and the surface is 0.25. Knowing that the system is released from rest at the position shown (h = 4 ft), determine the velocity of cylinder A when it strikes the ground. 6 in. A h 10 in. B

Chapter 17 Solutions

VECTOR MECH...,STAT.+DYN.(LL)-W/ACCESS

Ch. 17.1 - Prob. 17.6PCh. 17.1 - Prob. 17.7PCh. 17.1 - Prob. 17.8PCh. 17.1 - The 10-in.-radius brake drum is attached to a...Ch. 17.1 - Prob. 17.10PCh. 17.1 - Each of the gears A and B has a mass of 10 kg and...Ch. 17.1 - Solve Prob. 17.11, assuming that the 6 Nm couple...Ch. 17.1 - Prob. 17.13PCh. 17.1 - The double pulley shown has a mass of 15 kg and a...Ch. 17.1 - Gear A has a mass of 1 kg and a radius of gyration...Ch. 17.1 - A slender rod of length l and mass m is pivoted...Ch. 17.1 - The 15-kg rear hatch of a vehicle opens as shown...Ch. 17.1 - A slender 9-lb rod can rotate in a vertical plane...Ch. 17.1 - An adapted golf device attaches to a wheelchair to...Ch. 17.1 - A 10-kg storm window measuring 900 1500 mm is...Ch. 17.1 - A collar with a mass of 1 kg is rigidly attached...Ch. 17.1 - A collar with a mass of 1 kg is rigidly attached...Ch. 17.1 - Two identical slender rods AB and BC are welded...Ch. 17.1 - Prob. 17.24PCh. 17.1 - A 100-kg solid cylindrical disk, 800 mm in...Ch. 17.1 - Prob. 17.26PCh. 17.1 - Greek engineers had the unenviable task of moving...Ch. 17.1 - A small sphere of mass m and radius r is released...Ch. 17.1 - Prob. 17.29PCh. 17.1 - A half-cylinder with mass m and radius r is...Ch. 17.1 - Prob. 17.31PCh. 17.1 - Two uniform cylinders, each of weight W = 14 lb...Ch. 17.1 - Prob. 17.33PCh. 17.1 - A bar of mass m = 5 kg is held as shown between...Ch. 17.1 - The 1.5-kg uniform slender bar AB is connected to...Ch. 17.1 - The motion of the uniform rod AB is guided by...Ch. 17.1 - Prob. 17.37PCh. 17.1 - Prob. 17.38PCh. 17.1 - The ends of a 9-lb rod AB are constrained to move...Ch. 17.1 - The mechanism shown is one of two identical...Ch. 17.1 - The mechanism shown is one of two identical...Ch. 17.1 - Each of the two rods shown is of length L = 1 m...Ch. 17.1 - The 4-kg rod AB is attached to a collar of...Ch. 17.1 - If in Prob. 17.43 the angular velocity of the...Ch. 17.1 - The uniform rods AB and BC are of mass 3 kg and 8...Ch. 17.1 - The uniform rods AB and BC weigh 2.4 kg and 4 kg,...Ch. 17.1 - The 80-mm-radius gear shown has a mass of 5 kg and...Ch. 17.1 - Prob. 17.48PCh. 17.1 - Three shafts and four gears are used to form a...Ch. 17.1 - The experimental setup shown is used to measure...Ch. 17.1 - Prob. 17.51PCh. 17.2 - The 350-kg flywheel of a small hoisting engine has...Ch. 17.2 - Prob. 17.2IMDCh. 17.2 - Prob. 17.3IMDCh. 17.2 - Prob. 17.52PCh. 17.2 - A bolt located 2 in. from the center of an...Ch. 17.2 - A small grinding wheel is attached to the shaft of...Ch. 17.2 - A uniform 144-lb cube is attached to a uniform...Ch. 17.2 - Prob. 17.56PCh. 17.2 - Prob. 17.57PCh. 17.2 - Prob. 17.58PCh. 17.2 - Prob. 17.59PCh. 17.2 - Each of the double pulleys shown has a centroidal...Ch. 17.2 - Each of the gears A and B has a mass of 675 g and...Ch. 17.2 - Two identical uniform cylinders of mass m and...Ch. 17.2 - Two identical 16-lb uniform cylinders of radius r...Ch. 17.2 - Prob. 17.64PCh. 17.2 - Prob. 17.65PCh. 17.2 - Show that, when a rigid body rotates about a fixed...Ch. 17.2 - Prob. 17.68PCh. 17.2 - A flywheel is rigidly attached to a 1.5-in.-radius...Ch. 17.2 - A wheel of radius r and centroidal radius of...Ch. 17.2 - Prob. 17.71PCh. 17.2 - 17.72 and 17.73The 3-lb carriage C is supported as...Ch. 17.2 - Prob. 17.73PCh. 17.2 - Two uniform cylinders, each of mass m = 6 kg and...Ch. 17.2 - Prob. 17.75PCh. 17.2 - Prob. 17.76PCh. 17.2 - A sphere of radius r and mass m is projected along...Ch. 17.2 - A bowler projects an 8.5-in.-diameter ball...Ch. 17.2 - Prob. 17.79PCh. 17.2 - A satellite has a total weight (on Earth) of 250...Ch. 17.2 - Two 10-lb disks and a small motor are mounted on a...Ch. 17.2 - Prob. 17.82PCh. 17.2 - Prob. 17.83PCh. 17.2 - Prob. 17.84PCh. 17.2 - Prob. 17.85PCh. 17.2 - Prob. 17.86PCh. 17.2 - The 30-kg uniform disk A and the bar BC are at...Ch. 17.2 - Prob. 17.88PCh. 17.2 - A 1.8-kg collar A and a 0.7-kg collar B can slide...Ch. 17.2 - Prob. 17.90PCh. 17.2 - A small 4-lb collar C can slide freely on a thin...Ch. 17.2 - Rod AB has a weight of 6 lb and is attached to a...Ch. 17.2 - A 3-kg uniform cylinder A can roll without sliding...Ch. 17.2 - The 4-kg cylinder B and the 3-kg wedge A are at...Ch. 17.2 - The 6-lb steel cylinder A of radius r and the...Ch. 17.3 - A uniform slender rod AB of mass m is at rest on a...Ch. 17.3 - Prob. 17.5IMDCh. 17.3 - Prob. 17.6IMDCh. 17.3 - At what height h above its center G should a...Ch. 17.3 - A bullet weighing 0.08 lb is fired with a...Ch. 17.3 - In Prob. 17.97, determine (a) the required...Ch. 17.3 - A 16-lb wooden panel is suspended from a pin...Ch. 17.3 - Prob. 17.100PCh. 17.3 - A 45-g bullet is fired with a velocity of 400 m/s...Ch. 17.3 - A 45-g bullet is fired with a velocity of 400 m/s...Ch. 17.3 - The tire shown has a radius R = 300 mm and a...Ch. 17.3 - Prob. 17.104PCh. 17.3 - A uniform slender rod AB of mass m is at rest on a...Ch. 17.3 - A uniform slender rod AB is at rest on a...Ch. 17.3 - A bullet of mass m is fired with a horizontal...Ch. 17.3 - Determine the height h at which the bullet of...Ch. 17.3 - A uniform slender bar of length L = 200 mm and...Ch. 17.3 - A uniform slender rod of length L is dropped onto...Ch. 17.3 - A uniform slender rod AB has a mass m, a length L,...Ch. 17.3 - You have been hired to design a baseball catcher...Ch. 17.3 - The trapeze/lanyard air drop (t/LAD) launch is a...Ch. 17.3 - The uniform rectangular block shown is moving...Ch. 17.3 - The 40-kg gymnast drops from her maximum height of...Ch. 17.3 - A uniform slender rod AB of length L = 600 mm is...Ch. 17.3 - Prob. 17.118PCh. 17.3 - A 1-oz bullet is fired with a horizontal velocity...Ch. 17.3 - For the beam of Prob. 17.119, determine the...Ch. 17.3 - Prob. 17.121PCh. 17.3 - Prob. 17.122PCh. 17.3 - A slender rod AB is released from rest in the...Ch. 17.3 - Prob. 17.124PCh. 17.3 - Block A has a mass m and is attached to a cord...Ch. 17.3 - Prob. 17.126PCh. 17.3 - 17.127 and 17.128Member ABC has a mass of 2.4 kg...Ch. 17.3 - 17.127 and 17.128Member ABC has a mass of 2.4 kg...Ch. 17.3 - Prob. 17.129PCh. 17.3 - Prob. 17.130PCh. 17.3 - A small rubber ball of radius r is thrown against...Ch. 17.3 - Sphere A of mass m and radius r rolls without...Ch. 17.3 - In a game of pool, ball A is rolling without...Ch. 17 - A uniform disk, initially at rest and of constant...Ch. 17 - The 8-in.-radius brake drum is attached to a...Ch. 17 - A uniform slender rod is placed at corner B and is...Ch. 17 - The motion of the slender 250-mm rod AB is guided...Ch. 17 - A baseball attachment that helps people with...Ch. 17 - Disks A and B are made of the same material, are...Ch. 17 - Disks A and B are made of the same material, are...
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Text book image
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Text book image
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Text book image
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Text book image
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Text book image
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Dynamics - Lesson 1: Introduction and Constant Acceleration Equations; Author: Jeff Hanson;https://www.youtube.com/watch?v=7aMiZ3b0Ieg;License: Standard YouTube License, CC-BY