EBK MINDTAP FOR HERMAN'S DELMAR'S STAND
7th Edition
ISBN: 9781337900614
Author: Herman
Publisher: VST
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 17, Problem 1PA
An AC electric motor is connected to a 240-V, 60-Hz source. A clamp-on ammeter with a peak hold function reveals that the motor has an inrush current of 34 A when the motor is first started. Your job is to reduce the inrush current to a value of 20 A by connecting a resistor in series with the motor. The resistor will be shunted out of the circuit after the motor is started. Using an ohmmeter, you find that the motor has a wire resistance of 3
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Enumerate and explain briefly the three basic types of alternating current circuits.
A snubber circuit has snubber time constant (10 msec), voltage source (10 kV), discharge current of the Thyristor (5 µA) and frequency (50 Hz). Find the rate of voltage changing with time and snubber circuit power losses?
When the voltage source is turned off in a simple circuit
consists of a resistor and an inductor, the rate of decrease of
the current is proportional to the current. The current is 40
amperes at the moment that the switch is off and dies down
to 15 amperes after 0.01 sec. Determine the current in 0.02 sec.
3.375 amperes
4.25 amperes
5.625 amperes
6.025 amperes
Chapter 17 Solutions
EBK MINDTAP FOR HERMAN'S DELMAR'S STAND
Ch. 17 - 1. What is the relationship of voltage and current...Ch. 17 - What is the relationship of voltage and current...Ch. 17 - 3. What is power factor?
Ch. 17 - 4. A circuit contains a 20- resistor and an...Ch. 17 - 5. An R-L series circuit has a power factor of...Ch. 17 - 6. An R-L series circuit has an apparent power of...Ch. 17 - 7. The resistor in an R-L series circuit has a...Ch. 17 - 8. An R-L series circuit has a reactive power of...Ch. 17 - 9. An R-L series circuit contains a resistor and...Ch. 17 - 10. What is the voltage drop across the resistor...
Ch. 17 - 11. A phase angle meter connected in an R-L series...Ch. 17 - 12. An R-L series circuit has a power factor of...Ch. 17 - An AC electric motor is connected to a 240-V,...Ch. 17 - You are a journeyman electrician working in an...Ch. 17 - Assume that the circuit shown in Figure 17-2 is...Ch. 17 - Assume that the voltage drop across the resistor,...Ch. 17 - Assume the circuit shown in Figure 17-2 has an...Ch. 17 - Assume the circuit shown in Figure 17-2 has a...Ch. 17 - In an R-L series circuit,...Ch. 17 - In an R-L series circuit,...Ch. 17 - In an R-L series circuit,...Ch. 17 - In an R-L series circuit, the apparent power is...Ch. 17 - 9. An R-L series circuit is connected to a 60-Hz,...Ch. 17 - In an R-L series circuit, Z=88,R=32.FindXL.Ch. 17 - In an R-L series circuit, apparent power = 450 VA,...Ch. 17 - In an R-L series circuit, =22, true power = 94...Ch. 17 - An R-L series circuit contains two resistors and...Ch. 17 - An R-L series circuit contains two resistors and...Ch. 17 - An R-L series circuit contains two resistors and...Ch. 17 - An R-L series circuit contains two resistors and...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Given the zener voltage at 9V and the zener power at 1W, what is the range of allowable values of Iz (operating values). Choices: 0.11A 22mA to 89mA 9A 0.11A to 9A Plss show complete solutionarrow_forwardAn inductive load of 100 Ohm and 200mH connected in series to thyristor supplied by 200V dc source. The latching current of a thyristor is 45ma.and the duration of the firing pulse is 50us where the input supply voltage is 200V. Will the thyristor get fired?arrow_forwardEach terminal of a small polarity-independent incandescent bulb is connected to the positive terminals of two (2) DC voltage sources. The negative terminals of these sources are connected together. The first voltage source can have a range of value from 0-12, incrementable by 1.5 volts every turn of the rotary switch (i.e. 0 V, 1.5 V, 3 V, 4.5 V .... 12 V). The voltage of the second source is unknown. Using a luxmeter, the brightness of the lamp was measured for every increment of voltage of the first source. The following observations were recorded: a. 1.5 V produces a higher brightness than 3 V b. 0 V produces a higher brightness than 1.5 V c. 12 V produces higher brightness than 9 V d. 12 V produces equal brightness as 3 V What is the voltage of the second source? Justify each observation.arrow_forward
- What is the effect on induced voltage of adding more turns of wire to a coilarrow_forwardAn AC ammeter is connected in series with the primary winding of T1. What is the expected current reading? An AC ammeter is connected in series with the secondary winding of T1. What is the expected current reading? An AC ammeter is connected in series with R1. What is the expected current reading? NOTE: Idc for HW rectifier = 0.318 * Ipeak = 0.45 * Irms Describe/Explain briefly the purpose/use of the array (series-parallel) connection of the rectifier diodes in the given circuit.arrow_forwardA 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of 158 volts, 50 Hz supplies the combination. Determine the following: a. Circulating current b. Voltage across the resistor c. Voltage across the capacitorarrow_forward
- QUESTION 1 If a multiratio CT having 150:5 CT ratio with 0.104 ohm secondary resistance and the excitation current 0.2 A, I -SA Za1 ohm. a) Find the primary side of the CT and show the details of your work. b) Find the CT error and show the details of your work.arrow_forwardExplain the rectification alternating voltage into dc voltage with relevant waveformsarrow_forward10. Determine the peak-to-peak ripple and de output voltages in Figure 5. The transformer has a 36 V rms secondary voltage rating, and the line voltage has a frequency of 60 Hz. 120 Vrms 00000 ellee Rectifier B Figure 5. Rsurge www 10 (2 100 μF www R₁ 3.3 ΚΩarrow_forward
- Determine the loop currents Ia, I,, and Ic. 100 Ic 100 100 100 100 Ib 55V 100 V laarrow_forwardA wind turbine gives maximum output power of 1MW at a wind speed of 15m/s. Choose the correct statement for this wind turbine. a. The input wind power is 2.5MW b. The input wind power is 1.69MW c. The input wind power is 1.25MW d. The input wind power is 2.1MWarrow_forwardThere is an RL circuit with a switch 2-volt battery, a .15 H inductor, and a 60-ohm resistor. How long after the switch is closed would there be 10 milliamps in the circuit?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Delmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage Learning
Electricity for Refrigeration, Heating, and Air C...Mechanical EngineeringISBN:9781337399128Author:Russell E. SmithPublisher:Cengage Learning
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:9781337900348
Author:Stephen L. Herman
Publisher:Cengage Learning
Electricity for Refrigeration, Heating, and Air C...
Mechanical Engineering
ISBN:9781337399128
Author:Russell E. Smith
Publisher:Cengage Learning
Electrical Measuring Instruments - Testing Equipment Electrical - Types of Electrical Meters; Author: Learning Engineering;https://www.youtube.com/watch?v=gkeJzRrwe5k;License: Standard YouTube License, CC-BY
01 - Instantaneous Power in AC Circuit Analysis (Electrical Engineering); Author: Math and Science;https://www.youtube.com/watch?v=If25y4Nhvw4;License: Standard YouTube License, CC-BY