Electrical Transformers and Rotating Machines
4th Edition
ISBN: 9781305494817
Author: Stephen L. Herman
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 15, Problem 4RQ
To determine
The factors which determine the amount of torque developed by a DC motor.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Question 2
Beli vifth
Slack side
Motor
(imprut)
Tight side
Beli thickpess\
Centre distance
Figure 2
Figure 2 shows an open flat belt drive connected to a motor and a pulley. The
motor transmits 20 kw to the connect pulley of 450 mm diameter and is rotating
at 850 r/min to a second pulley rotating at 400 r/min. The distance between
pulley centres is approximately 2 m. The belt is 6 mm thick and has a density of
970 kg/m. The maximum stress in the belt is not to exceed 2,7 MPa. The
coefficient of friction for both pulleys is 0,3.
Determine:
2.1. The diameter of the second pulley.
2.2. The length of the belt.
3.3. The width of the belt taking centrifugal tension into account.
Given the following experimental data collected, what is the approximate torque of this motor at peak efficiency?
The reason why the starting torque of a series motor is higher than a shunt motor is
because the series motor has
O more current flowing through its armature
O a stronger net magnetic field around both coils during the inrush of stator current
Chapter 15 Solutions
Electrical Transformers and Rotating Machines
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A motor develops 189 ft-lb of torque at 1745 RPM. What is the horse-power output of the motor?arrow_forwardName three factors that determine the torque produced by an induction motor.arrow_forwardFor what purpose are synchronous motors used? Explain the V curves of the synchronous motor.arrow_forward
- A motor operating at 3450 rpm and is producing a torque of 33 lb in.what is the output horsepower of the motor?arrow_forwardQUESTION 8 Consider the equations of motion of an armature controlled DC motor given by Jw(t)+bw (t) Ki(t) = -Tfriction - Tload (t) di (t) + Ri (t) + Kw (t) = Vin (t), dt where vin(t) is the input voltage and Tload(t) is the input load torque. The outputs are the armature current i(t) and the motor speed w(t). The steady-state response of motors are specified by nominal voltage, stall torque, stall current, no load speed, and no load current. At steady-state operation, the motor equations satisfy bo) -Ki =-T -T. fric load Ri +Kov_- 55 55 The stall torque is the load torque required stead-state speed of the motor is zero. The stall current is the armature current when the motor speed is zero. The no load speed is the speed of motor when the load torque is zero. The no load current is the current when the load torque is zero. What is stall torque for this motor in N-m? Keep 3 significant figures, and do not include units. Use Scientific notation. The constants are given below. Nominal…arrow_forwardFind the horsepower rating of a motor running at 1,500 rpm and developing a torque of 105 lb–ft. (a). 22 (b). 28 (c). 30 (d). 36arrow_forward
- A (21 HP, 3-Phase, 380 volts) motor with an efficiency of 95% is operating at a load factor of 0.63. What is the input current (Amperes) when the power factor is 89%? (1 HP = 0.75 kW)arrow_forwardName three factors that determine the amount of voltage induced in the rotor of a wound-rotor motor.arrow_forwardQ1/ B/ A (220 V) series de motor runs at (400 rpm) and its useful torque is (100 Nm). If its efficiency at this load is (80% ), find the load current.arrow_forward
- What is the minimum pulley diameter for a 1 HP motor running at 1750 RPM?arrow_forwardName three factors that determine the amount of torque developed by a wound rotor induction motor.arrow_forwardA 480V, 3-phase, 50Hz 6-pole Induction motor with a rated power of 10KVA. (i) Calculate the synchronous speed in rad/sec (ws) (ii) Determine the rotor speed in rpm, if the % slip is 2.5%arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
Electrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage Learning
Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning