PEARSON ETEXT ENGINEERING MECH & STATS
15th Edition
ISBN: 9780137514724
Author: HIBBELER
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 14, Problem 81P
When s = 0, the spring on the firing
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The spring-held follower AB has a weight of 0.75 lb and moves
back and forth as its end rolls on the contoured surface of the
cam, where r=0.2 ft and z = (0.1sine) ft. If the cam is rotating at a
constant rate of 6 rad/s, determine the force at the end A of the
follower when e=90°. In this position the spring is compressed
0.4 ft. Neglect friction at the bearing C.
z = 0.1 sin 20
0.2 ft
e = 6 rad/s
k = 12 lb/ft
Fs
FA-
T
Determine the steady-state angle a if the constant force P = 195 N is applied to the cart of mass M = 16 kg. The cart travels on the
slope of angle 0 = 25° The pendulum bob has mass m = 4 kg and the rigid bar of length L = 1.1 m has negligible mass. Ignore all friction.
P
M
L
m
The helical path is wound around the circular cylinder with radiusR . The step h= 2*pi*R. The object A is sliding through the path guide under gravity (acting in the negative zdirection). There is no air resistance
1)Draw the force diagrams in (theta ,Z ) plane (tangent to the cylinder) and in( r,theta ) plane.
2) If the initial speed is 0, find the speed after 3 full circles. Given: R, g, m, u.[Hint: Use the work-energy principle.]
Chapter 14 Solutions
PEARSON ETEXT ENGINEERING MECH & STATS
Ch. 14 - Prob. 1FPCh. 14 - If the motor exerts a constant force of 300 N on...Ch. 14 - If the motor exerts a force of F = (600 + 2s2) N...Ch. 14 - The 1.8-Mg dragster is traveling at 125 m/s when...Ch. 14 - When s = 0.5 m, the spring is unstretched and the...Ch. 14 - The 5-lb collar is pulled by a cord that passes...Ch. 14 - Prob. 2PCh. 14 - The 100-kg crate is subjected to the forces shown....Ch. 14 - Determine the required height h of the roller...Ch. 14 - When the driver applies the brakes of a light...
Ch. 14 - Prob. 7PCh. 14 - The force F, acting in a constant direction on the...Ch. 14 - The 2-lb brick slides down a smooth roof, such...Ch. 14 - The two blocks A and B have weights WA = 60 lb and...Ch. 14 - A small box of mass m is given a speed of v=14gr...Ch. 14 - Prob. 18PCh. 14 - If the cord is subjected to a constant force of F=...Ch. 14 - The crash cushion for a highway barrier consists...Ch. 14 - The 25-lb block has an initial speed of v0 = 10...Ch. 14 - At a given instant the 10-lb block A is moving...Ch. 14 - Prob. 25PCh. 14 - The catapulting mechanism is used to propel the...Ch. 14 - Prob. 27PCh. 14 - Prob. 31PCh. 14 - When the 150-lb skier is at point A he has a speed...Ch. 14 - Prob. 39PCh. 14 - Prob. 40PCh. 14 - If the contact surface between the 20-kg block and...Ch. 14 - Prob. 8FPCh. 14 - Prob. 9FPCh. 14 - Prob. 10FPCh. 14 - Prob. 11FPCh. 14 - Prob. 12FPCh. 14 - The jeep has a weight of 2500 lb and an engine...Ch. 14 - Determine the power Input for a motor necessary to...Ch. 14 - An automobile having a mass of 2 Mg travels up a 7...Ch. 14 - Prob. 45PCh. 14 - To dramatize the loss of energy in an automobile,...Ch. 14 - Escalator steps move with a constant speed of 0.6...Ch. 14 - Prob. 48PCh. 14 - The 1000-lb elevator is hoisted by the pulley...Ch. 14 - The sports car has a mass of 2.3 Mg, and while it...Ch. 14 - Prob. 54PCh. 14 - Prob. 55PCh. 14 - The 50-lb block rests on the rough surface for...Ch. 14 - The 2-kg pendulum bob is released from rest when...Ch. 14 - Prob. 14FPCh. 14 - Prob. 15FPCh. 14 - Prob. 16FPCh. 14 - The 75-lb block is released from rest 5 ft above...Ch. 14 - Prob. 18FPCh. 14 - The girl has a mass of 40 kg and center of mass at...Ch. 14 - The 30-lb block A is placed on top of two nested...Ch. 14 - The 5-kg collar has a velocity of 5 m/s to the...Ch. 14 - The 5-kg collar has a velocity of 5 m/s to the...Ch. 14 - Prob. 71PCh. 14 - The roller coaster car has a mass of 700 kg,...Ch. 14 - The roller coaster car has a mass of 700 kg,...Ch. 14 - Prob. 76PCh. 14 - The roller coaster car having a mass m is released...Ch. 14 - The spring has a stiffness k = 200 N/m and an...Ch. 14 - Prob. 79PCh. 14 - Prob. 80PCh. 14 - When s = 0, the spring on the firing mechanism is...Ch. 14 - If the mass of the earth is Me, show that the...Ch. 14 - A rocket of mass m is fired vertically from the...Ch. 14 - The 4-kg smooth collar has a speed of 3 m/s when...Ch. 14 - Prob. 85PCh. 14 - Prob. 87PCh. 14 - Prob. 90PCh. 14 - The roller coaster car has a speed of 15 ft/s when...Ch. 14 - Prob. 1RPCh. 14 - The small 2-lb collar starting from rest at A...Ch. 14 - Prob. 3RPCh. 14 - Prob. 4RPCh. 14 - Prob. 5RPCh. 14 - Prob. 6RPCh. 14 - Prob. 7RPCh. 14 - Prob. 8RP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The particle of mass m = 2.1 kg is attached to the light rigid rod of length L = 0.91 m, and the assembly rotates about a horizontal axis through O with a constant angular velocity θ˙θ˙ = ω = 2.9 rad/s. Determine the force T in the rod when θ = 28°. The force T is positive if in tension, negative if in compression. Determine the force T in the rod when θ = 28°. The force T is positive if in tension, negative if in compression.arrow_forwardThe velocity of the 8-kg cylinder is 0.3 m∕s at a certain instant. The speed v after dropping an additional 1.5 m is 2.5 m/s. The mass of the grooved drum is 12 kg, its centroidal radius of gyration is k = 210 mm, and the radius of its groove is ri = 200 mm. The frictional moment at O is a constant 3 N∙m. Find the frictional force.arrow_forwardThe weight of the spring held follower AB is 0.381 kg and moves back and forth as its end rolls on the contoured surface of the cam, where r = 0.2 ft and z = (0.1sin20) ft. If the cam is rotating at a constant rate of 6 rad/s, determine the force, in Ib, at the end A of the follower where e = 45°. In this position, the spring is compressed 0.4 ft. Neglect friction at the bearing C. Round your answer to 3 decimal places. z = 0.1 sin 20 0.2 ft e = 6 rad/s A k = 12 lb/ftarrow_forward
- Determine the steady-state angle a if the constant force P = 170 N is applied to the cart of mass M = 43 kg. The cart travels on the slope of angle 0 = 17°. The pendulum bob has mass m = 9 kg and the rigid bar of length L = 1.1 m has negligible mass. Ignore all friction. M L m Answer: a = iarrow_forwardThe particle of mass m = 2.5 kg is attached to the light rigid rod of length L = 1.27 m, and the assembly rotates about a horizontal axis through O with a constant angular velocity = w = 3.2 rad/s. Determine the force T in the rod when 0 = 36°. The force Tis positive if in tension, negative if in compression. L Ꮎ marrow_forwardThe flat circular disk rotates about a vertical axis through O with a slowly increasing angular velocity w. Prior to rotation, each of the 0.52-kg sliding blocks has the position x = 28 mm with no force in its attached spring. Each spring has a stiffness of 430 N/m. Determine the value of x for each spring for a steady speed of 279 rev/min. Also calculate the normal force N exerted by the side of the slot on the block. The force N is positive if it pushes from the side labeled A. Neglect any friction between the blocks and the slots, and neglect the mass of the springs. (Hint: Sum forces along and normal to the slot.) Answers: X = wwwwwwww N = i i -74-74- mm mm mm Narrow_forward
- Determine the steady-state angle a if the constant force P = 200 N is applied to the cart of mass M = 19 kg. The cart travels on the slope of angle e = 18°. The pendulum bob has mass m = 4 kg and the rigid bar of length L = 1.9 m has negligible mass. Ignore all friction. M L Answer: a = iarrow_forwardThe homogeneous, solid cylinder with mass m = 4.8 kg and radius r = 0.24 m rolls along the inclined surface without slipping. If the initial angular velocity is w, = 2 rad/s (counterclockwise), and after a certain time lapse the angular velocity is w2 = 2.2 rad/s (clockwise), determine the magnitude of the linear impulse due to the frictional force during this time period. Let 0 = 46°.arrow_forwardThe smooth block B, having a mass of 1 kg, is attached to the vertex of the right circular cone using a light cord. If the block has a speed of 0.6 m/s around the cone, determine the tension in the cord and the reaction which the cone exerts on the block. Neglect the size of the block. 200 mm 400 mm 300 mmarrow_forward
- The steel ingot has a mass of 1940 kg. It travels along the conveyor at a speed v= 0,2 m/s when it collides with the "nested" spring assembly. If the stiffness of the outer spring is Ka= 5 kN/m, determine the required stiffness Kb of the inner spring so that the motion of the ingot is stopped at the moment the front, C, of the ingot is 0.3 m from the wall. (Answer in kN/m) 0.5 m -0.45 m kB k Barrow_forwardThe particle of mass m = 2.4 kg is attached to the light rigid rod of length L = 0.77 m, and the assembly rotates about a horizontal axis through O with a constant angular velocity θ˙θ˙ = ω = 3.5 rad/s. Determine the force T in the rod when θ = 29°. The force T is positive if in tension, negative if in compression.arrow_forwardThe quarter-circular slotted arm OA is rotating about a horizontal axis through point O with a constant counterclockwise angular velocity2=5.7 rad /sec. The 0.19-lb particle Pis epoxied to the arm at the position 3-56º. Determine the magnitude of the tangential force F parallel to the slot which the epoxy must support so that the particle does not move along the slot. The value of R-1.1 ft. B 22 R Parrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Dynamics - Lesson 1: Introduction and Constant Acceleration Equations; Author: Jeff Hanson;https://www.youtube.com/watch?v=7aMiZ3b0Ieg;License: Standard YouTube License, CC-BY