Concept explainers
(a)
The velocity of the plate immediately after the impact.
Answer to Problem 13.151P
The velocity of the plate immediately after the impact is
Explanation of Solution
Given information:
Speed of the ball
Mass of the ball
Mass of the plate
General impulse-momentum principal,
Newton’s equation of motion,
Calculation:
The velocity of the ball just before impact can be calculated as follows:
Newton’s equation of motion,
The velocity of the ball just after impact can be calculated as follows:
Newton’s equation of motion,
Applying general impulse-momentum principal,
Conclusion:
The velocity of the plate immediately after the impact is
(b)
The energy loss due to the impact.
Answer to Problem 13.151P
The energy loss due to the impact is
Explanation of Solution
Given information:
Speed of the ball
Mass of the ball
Mass of the plate
General impulse-momentum principal,
Newton’s equation of motion,
Kinetic energy,
Calculation:
Velocity just before impact,
Kinetic energy just before impact,
Velocity just after impact,
Kinetic energy just before impact,
Conclusion:
The energy loss due to the impact,
Want to see more full solutions like this?
Chapter 13 Solutions
Vector Mechanics For Engineers
- 150 mm A 500-g collar can slide without friction on 100 mm the curved rod BC in a vertical plane. Knowing that the undeformed length of the spring is 80 mm and that k = 400 kN/m, determine (a) the velocity that the collar should be 200'mm given at A to reach B with zero velocity, (b) the velocity of the collar when it eventually reaches C. Barrow_forwardA 1-oz bullet is fired with a horizontal velocity of 750 mi/h into the 18-lb wooden beam AB. The beam is suspended from a collar of negligible mass that can slide along a horizontal rod. Neglecting friction between the collar and the rod, determine the maximum angle of rotation of the beam during its subsequent motion.arrow_forwardA 32-g steel-jacketed bullet is fired with a velocity of 690 m/s toward a steel plate and ricochets along path CD with a velocity 500 m/s. Knowing that the bullet leaves a 50-mm scratch on the surface of the plate and assuming that it has an average speed of 600 m/s while in contact with the plate, determine the magnitude and direction of the impulsive force exerted by the plate on the bullet. 50 mm A 20° B C The magnitude of the impulsive force is 10° D KN and its direction is ° to the plate.arrow_forward
- ) Initially at rest, A Mitsubishi Pajero and a Toyota Vios are connected by a tow cable. The winch on the back of the Pajero is turned on and pulls in the tow cable at a constant relative velocity of 2 m/s. If both the 1.25 Mg Vios and the 2.5 Mg Pajero are free to roll, determine: a. The velocities of the jeep and the car at the instant they meet. b. If the tow cable is 5 m long, how long does it take for the vehicles to meet? FE 5marrow_forwardA 500-g collar can slide without friction on the curved rod BC in a horizontal plane. Knowing that the undeformed length of the spring is 80 mm and that k= 400 kN/m, determine (a) the velocity that the collar should be given at A to reach B with zero velocity, (b) the velocity of the collar when it eventually reaches C.arrow_forwardAn 8-kg collar slides without friction along a vertical rod as shown. The spring attached to the collar has an undeformed length of 12 cm and a constant of 575 N/m. f the collar is released from rest in the position shown, Determine the velocity if it has moved 20 cm down.arrow_forward
- Pin B has a mass m and slides along the slot in the rotating arm Oc and along the slot DE which is cut in a fixed horizontal plate. Neglecting friction and knowing that rod OC rotates at the constant rate 00. draw a FBD and KD that can be used to determine the forces P and Q exerted on pin B by rod OC and the wall of slot DE , respectively.arrow_forward4. A 750 kg hammer is used to drive a 2500 kg pile into some loosely packed sand. The hammer is released from a height of 2.5 m above the top of the pile and is seen to rebound to a maximum height of 0.15 m above the point of impact. Determine: (a) the velocity of the pile immediately after impact, (b) the coefficient of restitution, and (c) the average force exerted by the hammer on the pile if the impact takes place over 0.08 s. 2.5 m P Ans. vp, = -2.62 m/s, e = 0.62, Favg = 81.9 kN %3Darrow_forward. A small ball of mass 1 kg moving with a velocity of 12 m/s undergoes a direct central impact with a stationary ball of mass 2 kg. The impact is perfectly elastic. The speed (in m/s) of 2 kg mass ball after the impact will bearrow_forward
- A 10-kg package drops from a chute into a 25-kg cart with a velocity of 3 m/s. The cart is initially at rest and can roll freely. Determine (a) the final velocity of the cart, (b) the impulse exerted by the cart on the package, (c) the fraction of the initial energy lost in the impact.arrow_forwardA 1-lb stone is dropped down the “bottomless pit” at Carlsbad Caverns and strikes the ground with a speed of 95 ft/s. Neglecting air resistance, (a) determine the kinetic energy of the stone as it strikes the ground and the height h from which it was dropped. (b) Solve part aassuming that the same stone is dropped down a hole on the moon. (Acceleration of gravity on the moon = 5.31 ft/s2).arrow_forwardA 0.25-lb ball thrown with a horizontal velocity v0 strikes a 1.5-lb plate attached to a vertical wall at a height of 36 in. above the ground. It is observed that after rebounding, the ball hits the ground at a distance of 24 in. from the wall when the plate is rigidly attached to the wall (Fig. 1) and at a distance of 10 in. when a foam-rubber mat is placed between the plate and the wall (Fig. 2). Determine (a) the coefficient of restitution e between the ball and the plate, (b) the initial velocity v0 of the ball.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY