Physics for Scientists and Engineers
6th Edition
ISBN: 9781429281843
Author: Tipler
Publisher: MAC HIGHER
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 12, Problem 18P
To determine
To Find:The required value of the maximum distance.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
An amusement parkride consists of airplane-shaped carsattached to steel rods.Each rod has a length of 15.0 m anda cross-sectional area of 8.00 cm2.The rods are attached to a frictionlesshinge at the top, so that the cars canswing outward when the ride rotates.(a) How much is each rod stretchedwhen it is vertical and the ride is atrest? (Assume that each car plus twopeople seated in it has a total weight of1900 N.) (b) When operating, the ridehas a maximum angular speed of 12.0 rev/min. How much is the rodstretched then?
A uniform plank 8.00 m in length with mass 65.0 kg is supported at two points located 1.00 m and 5.00 m, respectively, from the left-hand end. What is the maximum additional mass you could place on the right-hand
end of the plank and have the plank still be at rest?
At the gym, you notice a girl doing a “plank.” In this exercise, she holds the position shownwithout moving. You approximate she supports four-tenths of her weight on each arm. Out of curiosity,you want to calculate the change in length of her arm due to compression by her body weight. Assumeshe weighs 52 kg, her arm is 30. cm long prior to the plank, and her arm is 5.0 cm in diameter. Yourealize that it is actually the bone that is supporting her weight, rather than the muscles and othertissues that make up the rest of her arm, so you guess the humerus is the main bone involved with thesame initial length as the arm and an average radius of 2.5 cm. If Young’s modulus for bone undercompression is 22 GPa, how much does the bone compress?
Chapter 12 Solutions
Physics for Scientists and Engineers
Ch. 12 - Prob. 1PCh. 12 - Prob. 2PCh. 12 - Prob. 3PCh. 12 - Prob. 4PCh. 12 - Prob. 5PCh. 12 - Prob. 6PCh. 12 - Prob. 7PCh. 12 - Prob. 8PCh. 12 - Prob. 9PCh. 12 - Prob. 10P
Ch. 12 - Prob. 11PCh. 12 - Prob. 12PCh. 12 - Prob. 13PCh. 12 - Prob. 14PCh. 12 - Prob. 15PCh. 12 - Prob. 16PCh. 12 - Prob. 17PCh. 12 - Prob. 18PCh. 12 - Prob. 19PCh. 12 - Prob. 20PCh. 12 - Prob. 21PCh. 12 - Prob. 22PCh. 12 - Prob. 23PCh. 12 - Prob. 24PCh. 12 - Prob. 25PCh. 12 - Prob. 26PCh. 12 - Prob. 27PCh. 12 - Prob. 28PCh. 12 - Prob. 29PCh. 12 - Prob. 30PCh. 12 - Prob. 31PCh. 12 - Prob. 32PCh. 12 - Prob. 33PCh. 12 - Prob. 34PCh. 12 - Prob. 35PCh. 12 - Prob. 36PCh. 12 - Prob. 37PCh. 12 - Prob. 38PCh. 12 - Prob. 39PCh. 12 - Prob. 40PCh. 12 - Prob. 41PCh. 12 - Prob. 42PCh. 12 - Prob. 43PCh. 12 - Prob. 44PCh. 12 - Prob. 45PCh. 12 - Prob. 46PCh. 12 - Prob. 47PCh. 12 - Prob. 48PCh. 12 - Prob. 49PCh. 12 - Prob. 50PCh. 12 - Prob. 51PCh. 12 - Prob. 52PCh. 12 - Prob. 53PCh. 12 - Prob. 54PCh. 12 - Prob. 55PCh. 12 - Prob. 56PCh. 12 - Prob. 57PCh. 12 - Prob. 58PCh. 12 - Prob. 59PCh. 12 - Prob. 60PCh. 12 - Prob. 61PCh. 12 - Prob. 62PCh. 12 - Prob. 63PCh. 12 - Prob. 64PCh. 12 - Prob. 65PCh. 12 - Prob. 66PCh. 12 - Prob. 67PCh. 12 - Prob. 68PCh. 12 - Prob. 69PCh. 12 - Prob. 70PCh. 12 - Prob. 72PCh. 12 - Prob. 73PCh. 12 - Prob. 74PCh. 12 - Prob. 75PCh. 12 - Prob. 76P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- One and of a uniform 3.30-m-long rod of weight w is supported by a cable at an angle of 8-37 with the rod. The other end rests against a wall, where it is held by friction (see figure). The coefficient of static friction between the wait and the rod is ,-0.525. Determine the minimum distance from point A at which an additional weight w (the same as the weight of the rod) can be hung without causing the rod to slip at point A 275 x Your response differs from the correct answer by more than 10% Double check your calculations, m Subnd Arowerarrow_forwardA horizontal plank 4.00 m long and having mass 20.0 kg restson two supports, one at the left end of the plank and a second1.00 m from the right end of the plank. What is the magnitude of theforce exerted on the plank by the support on the right side?arrow_forwarda uniform thin pole has a weight of 50 N and a length of 26 m If it is placed against the rough wall and on the rough box in the position d = 10 m, µs = 0.3 at points A, B and C P= 150 N Box weight = 100 N Determine the distance x when the motion of the pole impendarrow_forward
- A 15,000 N crane pivotsaround a friction-free axle atits base and is supported by acable making a 25° angle with thecrane (Fig. ). The craneis 16 m long and is not uniform,its center of gravity being 7.0 mfrom the axle as measured alongthe crane. The cable is attached3.0 m from the upper end of thecrane. When the crane is raised to55° above the horizontal holdingan 11,000 N pallet of bricks by a2.2 m, very light cord, find (a) thetension in the cable and (b) the horizontal and vertical components ofthe force that the axle exerts on the crane. Start with a free-body diagramof the crane.arrow_forwardIn the figure, a 10.0-m long bar is attached by a frictionless hinge to a wall and held horizont by a rope that makes an angle 0 of 53° with the bar. The bar is uniform and weighs 39.9 N. H far from the hinge should a 10.0-kg mass be suspended for the tension T in the rope to be 125 N? ... 10 kg 10 m A) 5.5 m from the hinge B) 6.4 m from the hinge C) 8.15 m from the hinge D) 7.7 m from the hingearrow_forwardA rigid body isa uniform square and has its center of gravity at the center. If the length and width of the square were to both halved where is the new center of gravity? O Not enough infomation to bell OIn the saame location O Halved from previous location O Doubled fom previous locationarrow_forward
- One end of a uniform beam of length L=3mandweight 185 Nis connected to a vertical wall with a cable. The other end is connected to a hinge. The cable makes an angle of 30 degrees with the beam. The cable can withstand a mnaximum tension of 427.0 N. A block of weight 204.0 N is placed on the beam at a distance xWhat is the maximum possible distance xbefore the cable breaks? Actiarrow_forwardA uniform 8.00 m, 1500 kg beam is hinged to a wall and supported by a thin cable attached 2.00 m from the free end of the beam. The beam is fixed to the wall at an angle of 30 degrees above the horizontal. The angle between the cable and the beam is 40 degrees. What are the unknowns? -direction of tension in the cable -direction of the hinge force -magnitude of rhe tension in the cable -magnitude of the hinge forcearrow_forward8-P10. The rectangular plate shown weighs 75 lb and is held in the position shown by hinges at A and B and by cable EF. If the hinge at B is removed and the hinge at A can exert couples about axes parallel to the y and z axes, determine (a) the tension in the cable, (b) the reactions at A and В. 4 in. F 12 in. 4 in. 25 in. B 30 in. 20 in. 8 in.arrow_forward
- A boy of mass 35.0 kg is standing on a uniform plank of mass 23.5 kg and length 6.00 m (Figure 11-63). The plank sits on two supports, one at the left end and the other 1.50 m from the right end. What is the maximum distance x at which the boy can stand on the overhanging part of the plank without the plank starting to tip? (Hint: When the plank begins to tip, what happens to the force exerted by the left-end support?)arrow_forwardHER A man holds a 175-N ball in his hand, with the forearm horizontal (see the drawing). He can support the ball in this position because of the flexor muscle force M, which is applied perpendicular to the forearm. The forearm weighs 21.4 N and has a center of gravity as indicated. Upper am bone Flexor muscle cing fc Elbow joint 89) 00510 m r 0.0890 m 0.330 m- (a) Find the magnitude of M 1149 X N (b) Find the magnitude and direction of the force applied by the upper arm bone to the forearm at the elbow joint. magnitude direction downward Additional Materials Book ??TO MacBook Ait 7.arrow_forwardA loaded cement mixer drivesonto an old drawbridge, where it stalls with its center of gravity threequartersof the way across the span. The truck driver radios for help,sets the handbrake, and waits. Meanwhile, a boat approaches, so thedrawbridge is raised by means of a cable attached to the end oppositethe hinge (Fig. ). The drawbridge is 40.0 m long and has a massof 18,000 kg; its center of gravity is at its midpoint. The cement mixer,with driver, has mass 30,000 kg. When the drawbridge has been raisedto an angle of 30° above the horizontal, the cable makes an angle of 70° with the surface of the bridge. (a) What is the tension T in the cablewhen the drawbridge is held in this position? (b) What are the horizontaland vertical components of the force the hinge exerts on the span?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Glencoe Physics: Principles and Problems, Student...PhysicsISBN:9780078807213Author:Paul W. ZitzewitzPublisher:Glencoe/McGraw-Hill
Glencoe Physics: Principles and Problems, Student...
Physics
ISBN:9780078807213
Author:Paul W. Zitzewitz
Publisher:Glencoe/McGraw-Hill
Static Equilibrium: concept; Author: Jennifer Cash;https://www.youtube.com/watch?v=0BIgFKVnlBU;License: Standard YouTube License, CC-BY