To plot: the mass flow parameter.
Answer to Problem 148P
Explanation of Solution
Given:
Mach number
Calculation:
Equation is given by
The graph for the above values is given below:
Conclusion:
Therefore, for the values Ma and k are plotted but only one value of
Want to see more full solutions like this?
Chapter 12 Solutions
Fluid Mechanics: Fundamentals and Applications
- The Mach number of an aircraft that travels with a speed of 260 m/s in air at 25° C while it undergoes the compressibility effect will be: (Use speed of sound in air at 0° C: 331 m/s) Select one: a. M = 0.69 b. M= 0.70 c. M= 0.75arrow_forwardWhat is the Mach Number of an air with a velocity of 250 m/s, at a temperature at 2800 meters?arrow_forwardFind the velocity of bullet fired in standard air if the Mach angle is 45°. Take R=287.14 J/kg K and k = 1.4 for air. Assume temperature as 27°Carrow_forward
- At a point in the flow over an F-15 high-performance fighter airplane, the density,temperature and Mach number are 1 kg/m3, 240 Kelvin, and Mach 1.6.(a) At this point, calculate T0, ρ0, p0, a0, T ∗, a∗, p∗ and the flow velocity.(b) Calculate M ∗1 and, using the Prandtl relation, calculate M ∗2 and u2 after a normalshock.arrow_forwardQ4//B/ Heat is removed from airflow in a constant-area duct, if flow enters at Mach 2.20, T1= 310 K, and p1= 120 kPa. Determine exit Mach number and the amount of heat removing from the duct if the static temperature at exit section is 255 K. justify your solution for M2arrow_forwardIn a wind tunnel air enters with a velocity of 200kmph. The static pressure and temperature of the air at the inlet of the tunnel is 110kPa and 27°C respectively. Determine Mach number, stagnation temperature, stagnation pressure and the stagnation density on a test model installed in the wind tunnel. The size of the tunnel is given as 1m x1m square cross-section. Determine the mass flow rate of the air. For air assume R=287J/kgK ; γ=1.4.arrow_forward
- Find the expression for the ratio of the stagnation pressure after a shock wave to the static pressure before the shock wave as a function of k and the Mach number upstream of the shock wave Ma1arrow_forwardA supersonic aircraft flies with a velocity lower by 39 m-s at 7800 m elevation, (T = - 54 C° at 7800 m) and (T = - 57 C° at 8800 m, M = 2), determine the difference between Mach no.s.arrow_forwardWhat is the Mach number of an airflow with a velocity of 2000m/s, at 2,000 ft altitude?arrow_forward
- The values of Cp for the consu Ammonia in air is a toxic mixture when the ammonia is 0.45% by volume. Calculate how much leakage from an ammonia compressor can be tolerated per 1000m³ of space. The pressure is 1bas and the temperature is 15 °C. The molar mass of ammonia (NH3) is 17kg/kmol, and it may assume to act as a perfect gas in this case. and 70 °C. The vessel is A perfect insulated vessel having three compartments A, B and C of volume 1.3m³, 1.2 m³ and 1.0 m² respectively are separated from each other by thin membrane. Compartment A is filled with ritrogen having a pressure 3bar, at a temperature 25 °C, compartment B is filled with hydrogen having a pressure of 20bar at a temperature -40 °C and compartment C filled with carbon (IV) oxide at a temperature 175 °C and pressure 6bar. If the thin membrane are punctured and the three gases allowed to mix freely, calculate: (i) The final temperature of the mixture The final pressure of the mixture (iii) The change in entropy of the…arrow_forwardConsider a point in an airflow where the local Mach number, static pressure, and static temperature are 2.5, 0.3 atm, and 180 K, respectively. Calculate the local values of P0, T0, T ∗, a∗, and M∗ at this pointarrow_forwardAt witch Mach numbers it is suitable to consider that Air density ρ = constant?arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY