To determine The specific heat at constant volume at final state. Explanation Write the expression for the Berthelot equation. p = R T v − b − a T v 2 (I) Differentiate the Equation (I) with respect to temperature. p = R T v − b − a T v 2 ( ∂ p ∂ T ) v = R v − b + a T 2 v 2 ( ∂ 2 p ∂ T 2 ) v = − 2 a T 3 v 2 (II) Here, the gas constant is R , the temperature is T , the volume of the liquid is v , the pressure is p and the constant are a and b . Write the expression for the constant a . a = 27 64 R 2 T c 3 p c (III) Here, the critical pressure is p c and the critical temperature is T c . Write the expression for the constant b . b = 1 8 R T c p c (IV) Write the expression for the specific heat at constant volume. C v = ∂ u ∂ T | v ( ∂ u ∂ v ) T = T ( ∂ u ∂ T ) v − p ∂ ∂ v [ ( ∂ u ∂ T ) v ] T = T ( ∂ 2 p ∂ T 2 ) v + ( ∂ p ∂ T ) v − ( ∂ p ∂ T ) v ( ∂ C v ∂ v ) T = T ( ∂ 2 p ∂ T 2 ) v (V) Substitute − 2 a T 3 v 2 for ( ∂ 2 p ∂ T 2 ) v in Equation (V). ( ∂ C v ∂ v ) T = T ( ∂ 2 p ∂ T 2 ) v C v ( T , v 2 ) − C v ( T , v 1 ) = 2 a T 2 v ] v 1 v 2 C v ( T , v 2 ) = C v + 2 a T 2 ( 1 v 2 − 1 v 1 ) (VI) Conclusion: Refer to Table A-1 “Atomic or molecular weights and critical properties of the selected elements and compounds” to obtain the critical properties of air as T c = 239 °R and p c = 37

Fundamentals of Engineering Thermodynamics

8th Edition

ISBN: 9781118412930

Author: Michael J. Moran, Howard N. Shapiro, Daisie D. Boettner, Margaret B. Bailey

Publisher: WILEY

See similar textbooks

Concept explainers

Properties of Pure Substances

A substance with fixed chemical composition throughout is called a pure substance like water, air, and nitrogen. A pure substance does not have to be a single element or compound. A mixture of two or more phases of a pure substance is also a pure substan…

Videos

Question

Chapter 11.9, Problem 63P

To determine

The specific heat at constant volume at final state.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 11.9, Problem 62P

Chapter 11.9, Problem 65P

Students have asked these similar questions

Q6/ A helical square section spring is set inside another, the outer spring having a free length of 35 mm greater than the inner spring. The dimensions of each spring are as follows: Mean diameter (mm) Side of square section (mm) Active turns Outer Inner Spring Spring 120 70 8 7 20 15 Determine the (1) Maximum deflection of the two springs and (2) Equivalent spring rate of the two springs after sufficient load has been applied to deflect the outer spring 60 mm. Use G = 83 GN/m².

Q2/ The bumper springs of a railway carriage are to be made of rectangular section wire. The ratio of the longer side of the wire to its shorter side is 1.5, and the ratio of mean diameter of spring to the longer side of wire is nearly equal to 6. Three such springs are required to bring to rest a carriage weighing 25 kN moving with a velocity of 75 m/min with a maximum deflection of 200 mm. Determine the sides of the rectangular section of the wire and the mean diameter of coils when the shorter side is parallel to the axis of the spring. The allowable shear stress is not to exceed 300 MPa and G = 84 kN/mm². Q6/ A belical

11. A load of 2 kN is dropped axially on a close coiled helical spring, from a height of 250 mm. The spring has 20 effective turns, and it is made of 25 mm diameter wire. The spring index is 8. Find the maximum shear stress induced in the spring and the amount of compression produced. The modulus of rigidity for the material of the spring wire is 84 kN/mm². [Ans. 287 MPa; 290 mm]

Chapter 11 Solutions

Fundamentals of Engineering Thermodynamics

Ch. 11.9 - Prob. 1E Ch. 11.9 - Prob. 2E Ch. 11.9 - 3. What is an advantage of using the Redlich–Kwong...Ch. 11.9 - To determine the specific volume of superheated...Ch. 11.9 - Prob. 5E Ch. 11.9 - Prob. 6E Ch. 11.9 - Prob. 7E Ch. 11.9 - Prob. 8E Ch. 11.9 - Prob. 9E Ch. 11.9 - Prob. 10E

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.