Fox and McDonald's Introduction to Fluid Mechanics
9th Edition
ISBN: 9781118912652
Author: Philip J. Pritchard, John W. Mitchell
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 11, Problem 52P
For a sharp-crested suppressed weir of length B = 8.0 ft, P = 2.0 ft, and H =1.0 ft, determine the discharge over the weir. Neglect the velocity of approach head.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A sharp crested suppressed weir under a head of 2.03 m is 3.50 m high and 2m long. Determine the discharge over the weir, if C = 0.603. Neglect the velocity of approach.
Q4: The flow is occurring in a rectangular channel at a velocity of (571/500) m/sec and a depth of 0.2 m. Neglecting the effect of the velocity of approach & applying the relation; Q=1.84*L*H3/2, Analyze that what should be the height of a sharp-crested weir that mustbe installed to raise the water depth upstream of the weir to 1.2 m.
Determine the height of a rectangular
weir of length 5m to be built across a
rectangular channel. The maximum depth
of water on the upstream side of the weir
is 1.5m and discharge is 1.5m^3 /sec
Take Cd =0.6 and neglect end
contractions.
Chapter 11 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Ch. 11 - Verify the equation given in Table 11.1 for the...Ch. 11 - A pebble is dropped into a stream of water that...Ch. 11 - Solution of the complete differential equations...Ch. 11 - A water flow rate of 250 cfs flows at a depth of 5...Ch. 11 - Determine and plot the relation between water...Ch. 11 - Capillary waves (ripples) are small amplitude and...Ch. 11 - The Froude number characterizes flow with a free...Ch. 11 - Consider waves on the surface of a tank of water...Ch. 11 - A submerged body traveling horizontally beneath a...Ch. 11 - Water flows in a rectangular channel at a depth of...
Ch. 11 - A partially open sluice gate in a 5-m-wide...Ch. 11 - Find the critical depth for flow at 3 m3/s in a...Ch. 11 - Flow occurs in a rectangular channel of 6 m width...Ch. 11 - What is the maximum flow rate that may occur in a...Ch. 11 - A rectangular channel carries a discharge of 10...Ch. 11 - Flow in the channel of Problem 11.15 has a...Ch. 11 - Consider the Venturi flume shown. The bed is...Ch. 11 - Eleven cubic meters per second of water are...Ch. 11 - A rectangular channel 10 ft wide carries 100 cfs...Ch. 11 - At what depths can 800 cfs flow in a trapezoidal...Ch. 11 - At a section of a 10-ft-wide rectangular channel,...Ch. 11 - Water, at 3 ft/s and 2 ft depth, approaches a...Ch. 11 - A horizontal rectangular channel 3 ft wide...Ch. 11 - A hydraulic jump occurs in a rectangular channel...Ch. 11 - A hydraulic jump occurs in a wide horizontal...Ch. 11 - A hydraulic jump occurs in a rectangular channel....Ch. 11 - The depths of water upstream and downstream from a...Ch. 11 - Calculate y2, h, and y3 for this two-dimensional...Ch. 11 - The hydraulic jump may be used as a crude flow...Ch. 11 - A hydraulic jump occurs on a horizontal apron...Ch. 11 - A hydraulic jump occurs in a rectangular channel....Ch. 11 - A positive surge wave, or moving hydraulic jump,...Ch. 11 - A 2-m-wide rectangular channel with a bed slope of...Ch. 11 - Determine the uniform flow depth in a rectangular...Ch. 11 - Determine the uniform flow depth in a trapezoidal...Ch. 11 - Water flows uniformly at a depth of 1.2 m in a...Ch. 11 - This large uniform open channel flow is to be...Ch. 11 - A rectangular flume built of timber is 3 ft wide....Ch. 11 - A channel with square cross section is to carry 20...Ch. 11 - A triangular channel with side angles of 45 is to...Ch. 11 - A flume of timber has as its cross section an...Ch. 11 - At what depth will 4.25 m3/s flow uniformly in a...Ch. 11 - A semicircular trough of corrugated steel, with...Ch. 11 - A rectangular flume built of concrete with 1 ft...Ch. 11 - Water flows in a trapezoidal channel at a flow...Ch. 11 - What slope is necessary to carry 11 m3/s uniformly...Ch. 11 - Find the normal depth for the channel of Problem...Ch. 11 - For a trapezoidal shaped channel with n = 0.014...Ch. 11 - Compute the critical depth for the channel in...Ch. 11 - A trapezoidal canal lined with brick has side...Ch. 11 - An optimum rectangular storm sewer channel made of...Ch. 11 - For a sharp-crested suppressed weir of length B =...Ch. 11 - A rectangular sharp-crested weir with end...Ch. 11 - What is the depth of water behind a rectangular...Ch. 11 - A broad-crested weir 0.9 m high has a flat crest...Ch. 11 - The head on a 90 V-notch weir is 1.5 ft. Determine...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Engine oil flows at a rate of 1kg/s through a 5mm diameter straight tube. The oil has an inlet temperature of 4...
Fundamentals of Heat and Mass Transfer
3.9 Find the resultant force R exerted on the pole.
Applied Statics and Strength of Materials (6th Edition)
Determine the horizontal and vertical components of reaction at the pin A and the reaction of the rocker B on t...
Engineering Mechanics: Statics
Show how you would do near orthogonal machining in a turning operation like that shown in Figure 21.3. (See Fig...
DeGarmo's Materials and Processes in Manufacturing
The cylinder volume below the constant loaded piston has two compartments, A and B, filled with water, as shown...
Fundamentals Of Thermodynamics
An evaporative cooling system is to be used to condition a large warehouse located in Denver, Colo.,(elevation=...
Heating Ventilating and Air Conditioning: Analysis and Design
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A trapezoidal channel (b= 1.5 m, m = 2) forms the outlet structure of a lake that discharges to a steep channel as shown in the figure. The lake level far upstream from the outlet is 0.6 m relative to the invert of the outlet structure. If the water discharge, Q, released from the lake was 1.86 m³/s, determine the depth y at the outfall. Flow direction Lake Outfall Q = 1.86 m³/s y = ? Steep channel TER 0.6 marrow_forwardA rectangular channel is 3.0 m wide and carries a discharge of 3.3 m³/s at a depth of 0.9 m. A smooth contraction of the channel width is proposed at a section. Find the smallest contracted width that will not affect the upstream flow conditions. Neglect the energy losses in the transition.arrow_forwardThe tank shown drains through a triangular weir whose flowrate is described by the equation given. Determine the time it will take for the tank to drain from completely full (h = 5 ft) to 5.25 feet deep (h = 0.25 ft) assuming there is no flow into the tank. Volumetric Flowrate h=5 ft + 5 ft 3 ft³ S = 2.48 h².5 (for h in feet) 10 ft -20 ft- -20 ft-arrow_forward
- A 3ft-diameter semicircular channel have a flow rate of 90 ft3 /s when the channel is full, determine the Hydraulic Radius.arrow_forwardA rectangular channel has a width of 3 m. If the discharge flowing in the canal is 2.1 m^3/s and coefficient of roughness n = 0.015, compute the critical slope.arrow_forwardDetermine the vertex angle of the V - notch weir cut at one end of a tank having a square section of 10m x 10m with an initial head of 1.20m. It discharges 100,000 liters of water in 380 seconds. Use correction factor, C = 0.60.arrow_forward
- Water flows in a rectangular channel with a width of 2.5 m. The kinetic energy correction coefficient (i.e. velocity coefficient) is estimated as a = 1.2. If the flow rate is 5 m³/s and the flow depth is 1.5 m: (a) determine the specific energy of the flow. (b) Calculate the alternate depth considering α = 1.0.arrow_forwardPlease give me right solution... Please remember I want correct solution A rectangular weir having a length of one meter is constructed at one end of a tank having a square section 20 x 20m and a height 10m. If the initial head on the weir is 1m, determine the time required to discharge a volume of 72 cu.m.arrow_forward4. The discharge from a 150 mm diameter orifice under a head of 3.05m and coefficient of discharge, C = 0.60 flows into a rectangular channel and over a rectangular suppressed weir. The channel is 1.83m wide and the weir has height, P = 1,50m and length, L = 0.31m. Determine the depth of water in the channel. Use Francis formula and neglect velocity of approach.arrow_forward
- What is the discharge of the pipe into reservoir B if a 1.2 m diameter concrete pipe 1800 m long carries a discharge of 1.417 cu m from reservoir A having an elevation of 90 m,this pipe discharges into two concrete pipes each 1350 m long and 750 mm in diameter.One of the pipe discharges into reservoir B at an elev. Of 84 m .The other pipe discharges into an open channel with a semi circular section having a slope of 0.001.Assuming n=0.011 for all pipes and channel and neglecting minor losses. Select one: O a. 0.122 cu m/s O b. 0.209 cu m/s Oc. 0.743 cu m /s O d. 0.865 cu m/sarrow_forwardThe radial gate used to control the flow at 2.5m wide rectangular channel. For a specific opening the discharge from this gate was 3.65-³/5. Find G for modular flow. use 8=20 and y₁=1.76m.arrow_forwardThe flow rate of water in a 10-m-wide horizontal channel is being measured using a 1.3-m-high sharp-crested rectangular weir that spans across the channel. If the water depth upstream is 3.4 m, determine the flow rate of water.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
8.01x - Lect 27 - Fluid Mechanics, Hydrostatics, Pascal's Principle, Atmosph. Pressure; Author: Lectures by Walter Lewin. They will make you ♥ Physics.;https://www.youtube.com/watch?v=O_HQklhIlwQ;License: Standard YouTube License, CC-BY
Dynamics of Fluid Flow - Introduction; Author: Tutorials Point (India) Ltd.;https://www.youtube.com/watch?v=djx9jlkYAt4;License: Standard Youtube License