Bundle: Refrigeration and Air Conditioning Technology, 8th + MindTap HVAC, 4 terms (24 months) Printed Access Card
8th Edition
ISBN: 9781337190350
Author: John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 11, Problem 2RQ
Three reference points that may be used to check temperature-measuring instruments are_________, _______, and______.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
True or False. In measurement there must be one-to-one correspondence between the numbers and the characteristics being measured.
True
False
Explain any two pressure measuring devices
Briefly discuss the concept behind each of the following measuring devices:a. LVDTb. strain gaugec. proving ringd. load cell
Chapter 11 Solutions
Bundle: Refrigeration and Air Conditioning Technology, 8th + MindTap HVAC, 4 terms (24 months) Printed Access Card
Ch. 11 - What does "calibrating an instrument" mean?Ch. 11 - Three reference points that may be used to check...Ch. 11 - Prob. 3RQCh. 11 - Temperature-measuring instruments may be designed...Ch. 11 - Glass stem thermometers are being replaced by...Ch. 11 - True or False: To check the temperature leads of...Ch. 11 - Accuracy of a thermometer is more important in the...Ch. 11 - Prob. 8RQCh. 11 - Prob. 9RQCh. 11 - What should a gauge manifold reading indicate when...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- what are plug gauges ? how to use them to judge a qualified part?arrow_forwardWhich statement is true in the case of the term "Range". The minimum and maximum values the instrument is designed to measure Is closely related to accuracy and output reading of an instrument is linearly proportional to the quantity being measured. Is not related to accuracy and define the maximum error of the measuring instrument during measurement process. Is closely related to accuracy and define the minimum and maximum values an instrument is designed to measure.arrow_forwardIn pressure gages, the difference between the actual value and error value (+/-) is called ___________.arrow_forward
- Which statement is true in the case of the term "Precision". The closeness of output readings when the same input is applied repetitively over a short period of time when there is change in condition of measurement. The closeness of output readings when the same input is applied repetitively over a short period of time when there is change in time of measurement. The closeness of output readings when the same input is applied repetitively over a short period of time when there is change in location. The closeness of output readings when the same input is applied repetitively over a short period of time and there is no change in observer.arrow_forwardWhich is the final element of a measurement system ?arrow_forwardWhat is the function of the following Pressure Measuring Instruments? •Bourdon Gauge •Bellows Pressure Gauge •Barometerarrow_forward
- In charpy test specimen, the angle of v-notch section is_- a. 60 degrees o b. 30 degrees O c. 90 degrees o d. 45 degreesarrow_forwardTolerance Maximum Limit Minimum Limit 50.7 mm 49.9 mm 26.8 cm 26.6 cm 0.04 mm 258.03 mm 0.12 mm 79.65 mm 0.0006 cm 12.731 cm 4.01 mm 3.98 mmarrow_forwardWhich of the following terms/ phrases describes the accuracy of measurement? a Depends on the instruments used b Standard deviation c Experimental error /Percent error d Reproducibility of a set of measurementarrow_forward
- نقطتان (2) * Select the right reading of the ?Micrometer Screw Gauge 0 0.125 mm O 0.150 mm 0.152 mm 0.120 mm 0.100 mm 0 tmt 20 أخرى:arrow_forwardApply geometrical tolerance to the below machine part in which the surface must be contained between two _______________planes 0.07 apart.arrow_forwardIdentify from the following measuring instrument, that can do Direct measurement. a. Vernier Caliper b. Micrometer c. Vernier Caliper d. Dial test indicatorarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Mod-01 Lec-16 Basics of Instrumentation; Author: nptelhrd;https://www.youtube.com/watch?v=qbKnW42ZM5c;License: Standard YouTube License, CC-BY