In Fig. 11-34, a constant horizontal force
Figure 11-34 Problem 11.
Want to see the full answer?
Check out a sample textbook solutionChapter 11 Solutions
Fundamentals of Physics Extended
Additional Science Textbook Solutions
College Physics: A Strategic Approach (4th Edition)
University Physics (14th Edition)
Physics for Scientists and Engineers: A Strategic Approach, Vol. 1 (Chs 1-21) (4th Edition)
EBK FUNDAMENTALS OF THERMODYNAMICS, ENH
Physics for Scientists and Engineers with Modern Physics
Life in the Universe (4th Edition)
- Consider the disk in Problem 71. The disks outer rim hasradius R = 4.20 m, and F1 = 10.5 N. Find the magnitude ofeach torque exerted around the center of the disk. FIGURE P12.71 Problems 71-75arrow_forwardA solid cylinder of mass 2.0 kg and radius 20 cm is rotating counterclockwise around a vertical axis through its center at 600 rev/min. A second solid cylinder of the same mass and radius is rotating clockwise around the same vertical axis at 900 rev/min. If the cylinders couple so that they rotate about the same vertical axis, what is the angular velocity of the combination?arrow_forwardA disk 8.00 cm in radius rotates at a constant rate of 1200 rev/min about its central axis. Determine (a) its angular speed in radians per second, (b) the tangential speed at a point 3.00 cm from its center, (c) the radial acceleration of a point on the rim, and (d) the total distance a point on the rim moves in 2.00 s.arrow_forward
- On a vertical plane, a uniform rigid disk rolls without slipping on an inclined surface under the effect of its own weight. The radius r of the disk equals 0.75 m and the mass m equals 10kg. Determine the acceleration of the disk, the necessary friction force at the point of contact between the disk and the inclined plane, and the needed minimum coefficient of static friction. If the disk were rolling up the inclined surface with an angular speed @= 2 rad / sec, determine how far up the surface the disk would travel while still rolling without slipping. 300arrow_forwardA cord is wrapped around the rim of a solid uniform wheel 0.250 m in radius and of mass 9.20 kg. A steady horizontal pull of 40.0 N to the right is exerted on the cord, pulling it off tangentially from the wheel. The wheel is mounted on frictionless bearings on a horizontal axle through its center. (a) Compute the angular acceleration of the wheel and the acceleration of the part of the cord that has already been pulled off the wheel. (b) Find the magnitude and direction of the force that the axle exerts on the wheel. (c) Which of the answers in parts (a) and (b) would change if the pull were upward instead of horizontal?arrow_forwardA mountain biker tries to start pedalling in the mud. The total mass (80 kg, bike + biker) is distributed equally between the front and rear wheels. There is a loss of 10% of moment of force between pedal and the rear wheel. The diameter of wheels is 70 cm, and the static friction coefficient between tyre and the mud is 0.3. The pedal angle is 25° from the vertical and has a length of 20 cm. The force exerted by the cyclist is vertical. What is the maximal force that the biker can produce without skidding?Hint 1: ImageHint 2: the value of Mp, the moment around the pedals, is about 50 Nm.arrow_forward
- Figure 10-33 gives angular speed versus time for a thin rod that rotates around one end. The scale on the w axis is set by ws = 6.0 rad/s. (a) What is the magnitude of the rod's angular acceleration? (b) At t = 4.0 s, the rod has rotational kinetic energy of 1.60 J. What is its kinetic energy at t = 0? | t (s) 4 Figure 10-33 Problem 34.arrow_forwardA small object with mass 4.00 kg moves counterclockwise with constant angular speed 1.50 rad/s in a circle of radius 3.00 m centered at the origin. It starts at the point with position vector 3.00î m. It then undergoes an angular displacement of 9.00 rad. (a) What is its new position vector? Use unit-vector notation for all vector answers. (b) In what quadrant is the particle located, and what angle does its position vector make with the positive x axis? (c) What is its velocity? (d) In what direction is it moving? (e) What is its acceleration? (f) Make a sketch of its position, velocity, and acceleration vectors. (g) What total force is exerted on the object?arrow_forwardA cylinder of mass M and radius R is pulled by a constant force of magnitude Fapplied at the top horizontally. The cylinder rolls smoothly on the horizontal surface. Assume that M=10 kg, R=0.10 m, F=12 N, and note that the rotational inertia of the cylinder about its axis is 1/2MR^2 (a) Find the magnitude of the acceleration of thic center of mass of the cylinder (please input the numerical value in unit of m/s) (b) Find the magnitude of the angular acceleration of the contact point between the cylinder and the surface about the axis of the cylinder (please input the numerical value in unit of rad/s). (c) Find the magnitude of the frictional force acting on the cylinder (please input the numerical value in unit of N).arrow_forward
- A hollow sphere of radius 0.120 m, with rotational inertia / = 0.0125 kg-m2 about a line through its center of mass, rolls without slipping up a surface inclined at 10.5° to the horizontal. At a certain initial position, the sphere's total kinetic energy is 18.0 J. (a) How much of this initial kinetic energy is rotational? (b) What is the speed of the center of mass of the sphere at the initial position? When the sphere has moved 1.30 m up the incline from its initial position, what are (c) its total kinetic energy and (d) the speed of its center of mass? (a) Number i Units (b) Number i Units (c) Number i Units (d) Number i Units > > > >arrow_forwardA nail is struck in the tread of a tire with radius r=0.17 m. It is held in with maximum frictional force f=0.55 n. The nail has a mass of m=11g. (A) what is the tire treads lowest tangential speed, in meters per second, at which the nail will pull free from the tire? Assume the tire is spinning vertically but not in contact with the lead. (B) at what tangential speed, in meters per second, will the nail pull free when it is at the top of the tire?arrow_forwardUsing a forked rod, a 0.5-kg smooth peg P is forced to move along the vertical slotted path r = (0.50) m, where is in radians. If the angular position of the arm is 0 = (²) rad, where t is in seconds, determine the force of the rod on the peg and the normal force of the slot on the peg at the instant t = 2 s. The peg is in contact with only one edge of the rod and slot at any instant. r = (0.50) marrow_forward
- Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage LearningPrinciples of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningUniversity Physics Volume 1PhysicsISBN:9781938168277Author:William Moebs, Samuel J. Ling, Jeff SannyPublisher:OpenStax - Rice University