Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
6th Edition
ISBN: 9780135257272
Author: James D. Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 10, Problem 6CQ
Two technicians are discussing the use of a typical bench/pedestal-mounted grinder. Technician A says that a wire brush wheel can be used to dean threads. Technician B says that the grinding stone can be used to clean threads. Which technician is correct?
a. Technician A only
b. Technician B only
c. Both Technicians A and B
d. Neither Technician A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
It is a small tool that features the standard angle (600) for lathe centers and for threading tool for American National Standard screw threads.
a. Gauge Block
b. Feeler Gauge
c. Center Gauge
d. Screw-Pitch Gauge
The following device is used to hold a workpiece
securely during drilling in Drilling machine
Select one:
a. Column
b. Base
c. Machine vice
d. Drill check
Give at least 5 purpose of cutting internal threads by the use of Lathe Machine.
Chapter 10 Solutions
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Ch. 10 - List the tools used by service technicians that...Ch. 10 - Which trouble light design(s) is (are) the...Ch. 10 - What safety precautions should be adhered to when...Ch. 10 - When using a blow gun, what precautions need to be...Ch. 10 - How is the size of a vise determined?Ch. 10 - When using compressed air and a blow gun, what is...Ch. 10 - Which air impact drive size is the most commonly...Ch. 10 - What type of socket should be used with an air...Ch. 10 - What can be used to cover the jaws of a vise to...Ch. 10 - Technician A says that impact sockets have thicker...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A screwdriver is identified by: 10. A. its torque. B. the length of its handle. C. the type of screw it fits. D. the width of its tip. The main differences between types of hand saws relate to their: A. teeth. 11. B. handles. C blades. D. frames. 12. If the drill bit binds in the material being drilled, what's the FIRST action you should take: A. back the drill out of the material. B. use the reversing switch to change directions. C. unplug the drill. D. release the trigger switch.arrow_forwardWhat can happen if a grinding stone with a lower-rated RPM than the grinder is used?arrow_forwardList down any four safety precaution need to carry during the operation of Lathe machine.arrow_forward
- 5. Name a tool that can be used to check an internal thread.arrow_forwardFrom the following identify the safety precaution for Milling machine. Sharp countersinks need to be using while milling Loosening of nuts should not be done by the machine torque . Nuts can be loosen by machine torque. The T-Handle should be removed from the chuck before millingarrow_forwardCarriage is mounted on the outer guide ways of lathe bed and it can move in a direction parallel to the spindle axis. TRUE or FALSEarrow_forward
- During operating lathe machine, the tool bit should be fixed as short as possible. Select one: True Falsearrow_forwardTechnician A says that carbon ceramic rotors can sometimes be machined. Technician B says that drums brakes with a diameter that's too wide and out of spec can be machined and made smaller. Who is correct? A. Technician A B. Technician B C. Both Technician A and B D. Neither Technician A or Barrow_forwardWhich among the following part which is not belonging to a milling machine. a. Compound slide b. Column c. Knee d. Worktablearrow_forward
- Therefore one of the following is correct. A. The depth of cut is 1.5mm B. The feed rate is 3mm. C. The feed rate is 1.5mm. D. The depth of cut is 3mm 16. Facing operation is performed on? A. Drilling machine. B. Sawing machine. C. Milling machine. D. Lathe machine. 17. The manufacturing process of removing material from the work piece is called. A. Milting and casting process. B. Machining process. C. Forming process. D. Extrusion processarrow_forwardwhat parts provide for toe-out on turnsarrow_forwardIdentify the part of a lathe machine which is used to take the cutting forces and vibrations during the machining process. Headstock Tailstock Tool post Bedarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage LearningPrecision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
HOME SHOP JIGS & FIXTURES PART 1, TYPES OF JIGS & ACCESSORIES AND THE THEORIE BEHIND THE TOOLS; Author: THATLAZYMACHINIST;https://www.youtube.com/watch?v=EXYqi42JimI;License: Standard Youtube License