Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
thumb_up100%
Chapter 1, Problem 7MC
Repair work performed on vehicles still under tire manufacturers warranty is usually performed by
- independent service shops
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
While diagnosing the problems that can be caused by worn tie-rod ends: Technician A says that they can cause scalloped and scuffed tires. Technician B says that they can cause the vehicle to pull to one side. Who is correct?
An indirect TPMS is being discussed. Technician A says that if a specific tire is low, the system will typically alert the driver which tire is low. Technician B says that after serving the indirect TPMS, you need to perform a re-learn procedure. Who is correct?
Technician A
Technician B
Both Technician A and B
Neither Technician A or B
Which of the following would NOT be cause for rejection when checking the tire condition?
Any tire has a fabric break or cut exposing ply or cord or any tire is in contact with the body or frame.
Any tire tread or recap is separated or any tire is flat.
All of the statements shown are cause for rejection.
Any tire has any bumps, bulges, or knots or is repaired with a boot or blowout patch.
Chapter 1 Solutions
Automotive Technology
Ch. 1 - List at least five different types of businesses...Ch. 1 - Name the different ways that you can gain work...Ch. 1 - Explain the implied difference between someone who...Ch. 1 - Explain the basic requirements for becoming a...Ch. 1 - Which of the following have had a significant...Ch. 1 - Individuals often begin a career as an automotive...Ch. 1 - Prob. 3MCCh. 1 - Prob. 4MCCh. 1 - Which of the following is typically included in a...Ch. 1 - Prob. 6MC
Ch. 1 - Repair work performed on vehicles still under tire...Ch. 1 - Prob. 8MCCh. 1 - Normally, whose job is it to greet the customer...Ch. 1 - Technician A says that all an individual needs to...Ch. 1 - To be successful, todays automotive technician...Ch. 1 - A technician must have a minimum of year(s) of...Ch. 1 - An experienced technician who passes all eight...Ch. 1 - Technician A says battery warranties are often...Ch. 1 - Prob. 15MCCh. 1 - Ongoing technical training and support is...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which of the following statements about unibody construction is not true? A unibody is a stressed hull structure in which each of the body parts supplies structural support and strength to the entire vehicle. Unibody vehicles tend to be tightly constructed because the major parts are all welded together. All unibodies are constructed from steel. Most front-wheel-drive unibody vehicles have a cradle or partial frame.arrow_forwardAll of the following statements are correct except? a. Tire inflation pressure directly affects traction. b. The recommended tire pressure for front and rear tires may be different. c. The recommended tire pressures are often lower than maximum pressures. d. The recommended tire pressure is molded into the sidewall of the tire.arrow_forwardList safety precautions that you should observe when operating a tractor on the field during field operationsarrow_forward
- Which of the following statements about unibodyconstruction is not true?a. A unibody is a stressed hull structure in whicheach of the body parts supplies structural supportand strength to the entire vehicle.b. Unibody vehicles tend to be tightly constructedbecause the major parts are all welded together.c. All unibodies are constructed from steel.d. Most front-wheel-drive unibody vehicles have acradle or partial frame.arrow_forwardAll of the following statements are correct except?a. Tire inflation pressure directly affects traction.b. The recommended tire pressure for front andrear tires may be different.c. The recommended tire pressures are oftenlower than maximum pressures.d. The recommended tire pressure is moldedinto the sidewall of the tirearrow_forwardWhile discussing what the maintenance reminders base die time for the next service on: Technician A says that future service is based on the type of driving the vehicle has seen since the last service. Technician B says that the next interval is based only on the number of miles or kilometers since the last service. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- While discussing pull during braking: Technician A says that this can be caused by one tire being underinflated. Technician B says that a frozen wheel cylinder on one side of the car can cause this. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardVehicle dynamics during braking are being discussed: Technician A says that the rear of the car rises during braking. Technician B says that the front of the car lowers during braking. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardTechnician A says that replacement wheel rims should be the same as the original equipment wheels in load capacity, offset, width, diameter, and mounting configuration. Technician B says that if wheels are installed that have a different stock width or diameter, make sure to use a tire that has the same overall width as the original tires. Otherwise the vehicles wheel-speed sensors, speedometer, antiock brake system, and many other systems will be affected. Who is correct? a. Technician A only b. Technician B only c. Both A and B Neither A nor Barrow_forward
- All of the following statements are correct except? a. Belts are reinforcing materials that encircle the tire under the tread. b. The carcass of a tire is made up of plies, layers of cloth, and rubber. c. Most tread patterns are designed to work well on both wet and dry roads. d. The bead is the decorative pattern at the outer edge of the tread.arrow_forwardAfter removing the vehicles hood in preparation for removing the engine: Technician A places the hood on the roof of the vehicle. Technician B sets the hood aside in a safe place on fender covers or cardboard. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardA tire that wobbles from side-to-side is said to have -----· a.radial runout b.lateral runout c.static imbalance d.none of the abovearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
General Industrial Safety; Author: Jim Pytel;https://www.youtube.com/watch?v=RXtF_vQRebM;License: Standard youtube license