A silicon pn junction diode at
a.
![Check Mark](/static/check-mark.png)
The forward-bias diode current for different values of
Answer to Problem 1.7TYU
For
For
For
Explanation of Solution
Given Information:
Calculation:
For
The diode current equation is:
The thermal voltage is determined as:
k = Boltzmann’s constant
The value of diode current is:
Hence, the value of forward bias diode current is,
For
The diode current equation is:
The thermal voltage is determined as:
k = Boltzmann’s constant
The value of diode current is:
Hence, the value of forward bias diode current is,
For
The diode current equation is:
The thermal voltage is determined as:
k = Boltzmann’s constant
The value of diode current is:
Hence, the value of forward bias diode current is,
b.
![Check Mark](/static/check-mark.png)
The reverse-bias diode current for different values of
Answer to Problem 1.7TYU
For
For
Explanation of Solution
Given Information:
Calculation:
For
The diode current equation is:
The thermal voltage is determined as:
k = Boltzmann’s constant
The value of diode current is:
Hence, the value of reverse-bias diode current is,
For
The diode current equation is:
The thermal voltage is determined as:
k = Boltzmann’s constant
The value of diode current is:
Hence, the value of reverse-bias diode current is,
Want to see more full solutions like this?
Chapter 1 Solutions
MICROELECT. CIRCUIT ANALYSIS&DESIGN (LL)
- As the forward current through a silicon diode increases, the voltage across the diode decreases and then increases. is relatively constant. increases to a 0.7 V maximum. decreases.arrow_forwardThe diode current at 25°C for a silicon diode with Is= 55 nA an applied forward bias of 0.8 V is -----. Note: use K=11600/2 0.543 A O 0.2 A 0.743 A 0.318 Aarrow_forwardThere are two LEDS that can be used as a polarity detector. Apply a positive source voltage and a green light results. Negative supplies result in a red light. Packages of such combinations are commercially available.Find the resistor R to ensure a current of 20 mA through the "on" diode for the configuration. Both diodes have a reverse breakdown voltage of 3 V and an average turn-on voltage of 2 V. * +8 V Red Green 350 ohms 330 ohms 310 ohms 300 ohms None of the abovearrow_forward
- The transition capacitance of semiconductor diode at reverse bias when applying a reverse voltage equal to 4 V is 5 nF. So the value of transition capacitance when applying a reverse voltage equal to 1 V isarrow_forwardConsider a silicon PN step junction diode with Assume T = 300 K.arrow_forwardA zener diode exhibits a certain change in VZ for a certain change in IZ on a portion of the linear characteristic curve between IZK and IZM as illustrated in Figure 5. Calculate the zener impedance.arrow_forward
- 1. Determine Vpout for the circuit in below and draw Vauts assume the diode is the silicon type. 10 k +10 V-- V. ov R, 100 k IN914 -10 V- 2. What is the output voltage that you would expect to observe across R, circuit of Figure below? Assume that RC is large enough to prevent significant capacitor discharge. +24 V 10 uF RL 10 kn V. ov. IN914 -24 Varrow_forwardA breakdown diode has iD=−10−6(1+vD/5)3 for −5 V<vD<0 where iD is in amperes. Plot iD versus vD in the reverse-bias region. Find the dynamic resistance of this diode at IDQ=−1 mA and at IDQ = -10 mA.arrow_forwardFor a diode in the forward bias region with n = 1 and VT = 26m V, if the current is divided by 10, None of the other answers O b. The voltage doesn't change O c. The voltage is reduced by approximately 60mV O d. The voltage is increased by approximately 60mVarrow_forward
- Question 1: In the circuit shown below, the output (Vo = 10V Max.) Unipolar. The frequency of Primary is 60 Hz. The diodes are Silicon with VD = 0.7V. a. Sketch the output without a Capacitor. b. Determine Voc without a Capacitor. c. Sketch Vs (at the Secondary). d. Determine Voc with a Capacitor of 10 uF across RL. e. Determine the RMS Value of Vp (at the Primary). f. PIV (Peak Inverse Voltage). 10:1 Output C. 22 k1 All diodes are IN4001. | 00000arrow_forwardA- If V, is a sinusoidal voltage with Vm = 40 V, and V= 15 V. Plot the waveform of the output voltage in each of the following clippers circuits assuming ideal diodes. B- Repeat part (A) if the diodes are silicon diodes. R R R (a) (b) (c) (d)arrow_forwardFor the circuit below with E = 10 V, R = 5800 N. Find the following: a) current in the circuit b) voltage across the diode c) voltage across the resistor Anode (A) Cathode (K) b E R wwwwarrow_forward
- Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSONDelmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage LearningProgrammable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
- Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill EducationElectric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSONEngineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,
![Text book image](https://www.bartleby.com/isbn_cover_images/9780133923605/9780133923605_smallCoverImage.gif)
![Text book image](https://www.bartleby.com/isbn_cover_images/9781337900348/9781337900348_smallCoverImage.jpg)
![Text book image](https://www.bartleby.com/isbn_cover_images/9780073373843/9780073373843_smallCoverImage.gif)
![Text book image](https://www.bartleby.com/isbn_cover_images/9780078028229/9780078028229_smallCoverImage.gif)
![Text book image](https://www.bartleby.com/isbn_cover_images/9780134746968/9780134746968_smallCoverImage.gif)
![Text book image](https://www.bartleby.com/isbn_cover_images/9780078028151/9780078028151_smallCoverImage.gif)