Heating, Ventilation, and Air Conditioning: Analysis and Design
6th Edition
ISBN: 9781119628798
Author: Faye C. McQuiston; Jerald D. Parker; Jeffrey D. Spitler
Publisher: Wiley Global Education US
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 1, Problem 1.11P
Compute the heat transferred from water as it flows through a heat exchanger at a steady rate of 1 m3/s. The decrease in temperature of the water is 5 C, and the mean bulk temperature is 60 C. Use SI units.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A steam condenser receives 10 kg per second of steam with an enthalpy of 2570 KJ/kg. Steam condenses into liquid and leaves with an enthalpy of 160 KJ/kg, if cooling water passes through the condenser with temperature increases from 13oC to 24oC. Calculate the cooling water flow rate in kg/sec.
Show conversion of units pls
In a heat exchanger, water flows through a long copper tube (inside diameter 2.2 cm) with an average velocity of 2.13 m/s. The water is heated by steam condensing at 150 degree celsius on the outside of the tube. Water enters at 15 degree Celsius and leaves at 60 degree Celsius . What is the heat transfer coefficient, h, for the water? Write the given, required and solution
As a process engineer, you are given the task to design a heat exchanger to
cool a tank for mixing water and sulfuric acid. Based on the data below, calculate the
rate of heat transfer needed to maintain the temperature at 300 K for mixing the following
two streams (stream 1 mixed with stream 2).
Stream 1: A solution of 25 wt.% sulfuric acid at 300 K flowing at 2 kg/s
Stream 2: A solution of 40 wt.% sulfuric acid at 350 K flowing at 1 kg/s
Copyright e Meiraw- Education. Permission reguired for reproducton or dapiay
300
200
100
350 K
-100
300 K
-200
-300
250
-400
-500
10
20
30
40
50 60
Wt. % H,SO,
70
80
90
100
H/kJ (kg solution)
Chapter 1 Solutions
Heating, Ventilation, and Air Conditioning: Analysis and Design
Ch. 1 - Convert the following quantities from English to...Ch. 1 - Convert the following quantities from SI to...Ch. 1 - A pump develops a total head of 50 ft of water...Ch. 1 - A fan is observed to operate with a pressure...Ch. 1 - The electric utility rate for a facility during...Ch. 1 - For the business whose monthly electrical energy...Ch. 1 - Detmine the interest rate at which the project in...Ch. 1 - How much could a company afford to spend on an...Ch. 1 - Make the following volume and mass flow rate...Ch. 1 - A room with dimensions of 31020m is estimated to...
Ch. 1 - Compute the heat transferred from water as it...Ch. 1 - Air enters a heat exchanger at a rate of 5000...Ch. 1 - Water flowing at a rate of 1.5 kg/s through a heat...Ch. 1 - Air at a mean temperature of 50 F flows over a...Ch. 1 - Repeat Problem 1-10 for air at 10 C, a tube with...Ch. 1 - Air at 1 atm and 76 F is flowing at the rate of...Ch. 1 - Air flowing at the rate of 1000 cfm and with a...Ch. 1 - A chiller is providing 5 tons of cooling to an air...Ch. 1 - Air is delivered to a room at 58 F and the same...Ch. 1 - A chiller is to pro;ide 12 tons of cooling to a...Ch. 1 - Air is being rnished to a 30-ft by 40-ft by 12-ft...Ch. 1 - If cold outside air at 20 F is leaking into a...Ch. 1 - A Btu-meter is a device that measures water flow...Ch. 1 - A heat pump uses a 100,000-gallon swimming pool as...Ch. 1 - A heat pump uses a 100,000-gallon swimming pooi as...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
The volumetric flow rate and discharge velocity of the air.
Introduction to Heat Transfer
(a) If the cone shown in Fig. 5.34 is made of pine wood with a specific weight of 30lb/ft3, will it be stable i...
Applied Fluid Mechanics (7th Edition)
Determine the friction force at the surface of contact. Prob. P81
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
An F-4 aircraft makes a high-speed pass over an airfield on a day when T = 35°C. The aircraft flies at M = 1.4 ...
Fox and McDonald's Introduction to Fluid Mechanics
Determine the maximum force P that can be applied without causing the two 50-kg crates to move. The coefficient...
Engineering Mechanics: Statics
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 4. The following heat exchanger uses 10 kg/s of hot air to heat and boil liquid water into saturated steam at 500 kPa. (a) Find the steam flow (kg/s) (b) Determine whether the process is allowed by the second law (Answer: It is not!) (c) On the surface, the process looks OK as Tair>Twater at both the inlet and outlet. You should be able to see the problem if you sketch the air and the water temperature profiles as you move left to right through the exchanger. (Hints: The air will be essentially a straight line, while the water will not. For the water, think about what happens when it is changing phase.) This is called a pinch point violation, and it is a very important design consideration in advanced combined cycle systems and in nuclear power plants. Air 100 kPa 160°C 10 kg/s Saturated Vapor 500 kPa Air: 160°C Steam: 151.8°C Q Air 100 kPa 30°C Liquid Water 500 kPa, 20°C Air: 30°C Water: 20°Carrow_forward2-) 10500 kg/hr of water is heated using a counter-flow, double-pipe heat exchanger utilizing superheated steam. Steam passes through the heat exchanger at 130 °C after entering at 180 °C. Water has an entrance temperature of 30 °C and an outlet temperature of 80 °C. Calculate the heat transfer area if the overall heat transfer coefficient from steam to water is 814 W/m² K. How much more area would there be if the fluid flow was parallel?arrow_forward(a) A storage tank is connected to a piping system as illustrated in Figure P1. Water at temperature of 20°C in the storage tank flows through a piping system with the pipe's diameter of 5 cm and discharges from a nozzle to the atmospheric at velocity of 3.5 m/s. The diameter of the nozzle is 3cm. Galvanized pipe is used and installed in this piping system. All the fitting components installed in this system such as regular 90° and tees are flanged type. Water at 20°C 21 m D-5 cm d-3 cm Figure P1 i. By using suitable assumptions, predict the friction factor of this piping system (Including the Moody Chart is necessary). ii. According to the obtained friction factor in section P1(a), determine the possible pipe length of this piping system ii. After 5 years of operation, the accumulation of the dirt and other micro particles stained on the pipe's wall surface have significantly reduced the water discharge from the nozzle. Please explain this phenomenon. |arrow_forward
- The following data for steam condenser: Steam condensed = 50000 kg/h; Temperature of steam in condenser = 40 oC; Dryness of steam entering into condenser=0.85; The air leakage in the condenser = 150 kg/h; Temperature of the condensate = 35oC. Find: (1) The air leakage pressure. (2) Quantity of cooling water passed through the condenser per hour if the rise in cooling water temperature is limited to 10oCarrow_forwardMechanical engineering : Heat transfer 1. Determine the overall heat transfer coefficient and flow rate required while using a heat exchanger , the water is enetered at 20◦C through the tubes of small single pass and the water comes out with a temperature at 40◦C. 25 kg/min of steam condenses at 60◦C on the shel side ,the area of the exchanger is 12 m2. (The latentheat, hfg, is 2358.7 kJ/kg at 60◦C.) 2 . You have unpainted aluminum siding on your house and the engineerhas based a heat loss calculation on U = 5 W/m2K. You discover thatair pollution levels are such that Rf is 0.0005 m2K/W on the siding.Should the engineer redesign the siding? If not sure skip, wrong may downvotearrow_forwardFor Heat transfer through cylinder tube wall, the temperature is to be a linear function of r (radius) of the tube. Select one: O True O False The conductivity of H20 in solid form (ice) is higher than that of H20 in liquid form (water). Select one: O True O False F, (Correction factor for temperature in some heat exchangers) should be 1.0 or greater than 1.0 in some cases. Select one: O True Falsearrow_forward
- Table Q3 is given to collect the temperature of hot and cold water at the inlet and outlet positions in the laboratory using Tube Heat Exchanger (TD360a) by varying the cold-water flow rate to investigate the effect of cold-water flow rate on the heat exchanger’s performance. (a) Complete all the output parameters indicated in the table given in Appendix 1. (b) Draw the temperature (TH1, TH2, TC1 and TC2) on the vertical vs position (1, 2) on the horizontal axis for each flow and discuss the effect of cold water flow rate change on the exit temperature of both cold water and hot water. (c) Draw the graph of Energy Balance Coefficient and Mean Temperature Efficiency on vertical axis and cold-water flow rate on horizontal axis. Discuss the effect of flow rate on the Energy Balance Coefficient and Mean Temperature Efficiency based on your finding.arrow_forwardCompressed liquid water at 10 MPa and 20 C enter a steam generator (Heat exchanger) which has a uniform 30-mm diameter tube at a rate of 3 L/s. Find the rate of heat added to the water (in kW) if it exists at 9 MPa and 400 C. Select one O a. 8333.8 kW O b. 8638.8 kW O C. 9131.2 kW d. 9556.4 kW O e. 7854.2 kW O f. None of the abovearrow_forwardQ1] A shell and tube heat exchanger is used to heat water (C = 4236 J/kg. °C) from 80°C to 150°C at a rate of 12.5 kg/s by hot gas that enters the exchanger at 350°C with a rate of 20.36 kg/s. The overall heat transfer coefficient is 290 W/m² °C. The gas making 2-shell passes and the water making 4-tube passes. Calculate the heat transfer surface area (Cp (gas) = 1.04 kJ/kg.°C). heat flux: (a) byarrow_forward
- 3.21 You must cool 78 kg/min of a 60%-by-mass mixture of glycerin in wa- ter from 108°C to 50°C using cooling water available at 7°C. Design a one-shell-pass, two-tube-pass heat exchanger if U = 637 W/m²K. Which side should the water flow through? Explain any design decision you make and report the area, TH₂0out and any other relevant features.arrow_forwardPLEASE ANSWER ASAP In a heat exchanger, water flows through a long copper tube (inside diameter 2.2 cm) with an average velocity of 2.13 m/s. The water is heated by steam condensing at 150 degree celsius on the outside of the tube. Water enters at 15 degree Celsius and leaves at 60 degree Celsius . What is the heat transfer coefficient, h, for the water? Write the given, required and solutionarrow_forward6. A heat exchanger was installed purposely to cool 0.50 kg of gas per second. Molecular weight is 28 and k=1.32. The gas is cooled from 150 deg C to 80 deg C. Water is available at the rate of 0.30 kg/s and at a temperature of 12 deg C. Calculate the exit temperature of the water.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
How Shell and Tube Heat Exchangers Work (Engineering); Author: saVRee;https://www.youtube.com/watch?v=OyQ3SaU4KKU;License: Standard Youtube License