You're calculating the volume of a cube with an edge length of 0.250 inches. Which of the following should be used to express the cube's volume? Assume a round-up rule if the digit in the next lower decimel place is "5" or greater. Group of answer choices 1.56E-2 cubic inches 1.6E-2 cubic inches 1.563E-2 cubic inches

You're calculating the volume of a cube with an edge length of 0.250 inches. Which of the following should be used to express the cube's volume? Assume a round-up rule if the digit in the next lower decimel place is "5" or greater. Group of answer choices 1.56E-2 cubic inches 1.6E-2 cubic inches 1.563E-2 cubic inches

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter14: Computational Engineering Tools Electronic Spreadsheets

Section: Chapter Questions

Problem 33P

See similar textbooks

Similar questions

Which of the following is the fastest speed? E Click the icon to view the conversion table. Choose the correct speed below. O A. 4 miles per hour [mi/h or mph] O B. 7 centimeters per second [cm/s] OC. 710 feet per minute [ft/ min]
Calculate the required area of the column,Ag, and give your answer in inches squared (in^2).
Write your final answer in two decimal places in the unit of kN-m.
Question 29 4 pts What is the weight (Ibf) of a cube of stainless steel with 6.5 cm on each edge? Express your final answer in two decimal places. No need to type the units. 4.85 Next
Please show solutions on how to get the 1500 value. The circle green in the figure. Civil engineering- steel design Note: I thought the value of area 2 is 3750. Area 2: 25x150= 3750 mm2. Feel free to correct me . What should put in circle in the figure.
Determine the centroid along the x-axis and y-axis of the figure shown: (each side of a square= 2 units) The base is 3 units long; consider the left corner of the figure as the point of origin. Express your answer in at least 3 decimal digits.
Problem 01: Given the figure at the right side: Determine the following a. Zx b. Sx c. shape factor 200 200 150
Part H dH = 320 mm Part H - There are 2 questions in this part Refer to your email from Tim which defined values of the different variables. Consider the shape below. It is made of solid aluminium (E = 70000 MPa). The shape can be considered as a rectangle 2dμ x dμ with semi circular portions top and bottom. 2d4 Question 22 Question H1 What is the second moment of area about the horizontal centroidal axis? You will not be able to enter your answer using exponential powers of 10 - eg if the answer is 3.456 x 106 you would need to enter 3456000. You must get both questions of this part correct to get marks. Question 23 Question H2 What is the second moment of area about the vertical centroidal axis? You will not be able to enter your answer using exponential powers of 10 - eg if the answer is 3.456 x 106 you would need to enter 3456000. You must get both questions of this part correct to get marks.
Build the following part. Report the volume in mm^3. Assume all dimensions are in mm. A = 38 B = 17 R10 A-20 10 45°
Instructions: Use Dimensional Analysis & Chain conversion method. (Provide in Both) (In detail with each Formula) (handwritten will be appreciated) 1. Convert 102.5 km to miles 2. Convert 0.325 km to millimeters 3. Convert 15 km² to in² 4. Convert 24 quarts to cubic centimeters (cm³)
Locate the center of mass of the homogeneous block assembly. 250 mm 200 mm 150 mm j00 mm 150 mm 150 mm Answer: m y = 11 | Page
subtract the decimal fractions 582.476 liters-488.827 liters