Part HdH = 320 mmPart H - There are 2 questions in this partRefer to your email from Tim which defined values of the different variables.Consider the shape below. It is made of solid aluminium (E = 70000 MPa).The shape can be considered as a rectangle 2dμ x dμ with semi circular portions top and bottom.2d4Question 22Question H1What is the second moment of area about the horizontal centroidal axis?You will not be able to enter your answer using exponential powers of 10 - eg if the answer is 3.456 x106 you would need to enter 3456000.You must get both questions of this part correct to get marks.Question 23Question H2What is the second moment of area about the vertical centroidal axis?You will not be able to enter your answer using exponential powers of 10 - eg if the answer is 3.456 x106 you would need to enter 3456000.You must get both questions of this part correct to get marks.

From the given question it is required to calculate the moment of inertia about centroidal axis.

Part H - There are 2 questions in this part Refer to your email from Tim which defined values of the different variables. Consider the shape below. It is made of solid aluminium (E = 70000 MPa). The shape can be considered as a rectangle 2d x d with semi circular portions top and bottom.

Part H - There are 2 questions in this part Refer to your email from Tim which defined values of the different variables. Consider the shape below. It is made of solid aluminium (E = 70000 MPa). The shape can be considered as a rectangle 2d x d with semi circular portions top and bottom.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Q2): 1200 BPD of 32 ° API crude oil is fed to an atmospheric distillation unit, the following pro-…

A: Given:

Q: Problem Number 2: Determine the Moment of Inertia, I, & I, and the radius of Gyration r, & ry.. Y…

Q: A soil has a liquid limit of 61 and plastic limit of 30. A moisture content test yielded the…

A: Given: liquid limit Plastic limit Mass of soil before oven drying Mass of soil after oven drying…

Q: H.W2 Determine the maximum deflection of the simply supported beam. E = 200 GPa and I = 39.9(106)…

Q: etermine the ffg: Support Reactions, Shear and Moment Equations. For the last segment use the FBD of…

Q: Determine the maximum horizontal uniform load, ω= ______________ KN/m can the cable safely carry if…

A: The values and diagram given in the question are as follows: Diameter of cable(d)=105.5555 mm…

Q: 사 6 m 75 kN B 6m. C 25 kN/m 6 m D

Q: Z a L₁ (1) B 2To L2 (2) L3 To C (3) D X

Q: P1 L1/2 W1 B -L1 P2 A SET (1) L1 3 m L2 4 m P1 5 KN -L2 P2 6 KN W1 7 KN/m W2 6 KN/m PROB 01 Support…

Q: Viscosity of a fluid with specific gravity 1.3 is measured to be 0.0034 Ns/m². Its Kinematic…

A: Given data- specific gravity SG=1.3viscosity μ=0.0034 Ns/m2To find-kinematic viscosity v

Q: L.L. is 10 KN/m², which covers the left half of the 1. for the girder at 25 m from the left end.…

A: SOLUTION OF ABOVE PROBLEM IS BELOW::

Q: For the beam and loading shown, determine the shear and moment as functions of position, and choose…

A: It is given that :

Q: In fig. if h1 = 3 ft. h2= 1.5 ft, the pressure at A =---? (S.G1= 0.7, S.G2= 0.8) s.g.1 S.G2 h₂

Q: you please write this on paper so I can easily understand it? It will be a great help thank you

Q: the heam

Q: Solve for the slope and deflection of the beam as shown below using Double Integration Method. M M L…

Q: Problem 2: It is recommended to change the circular cross section shown in the figure by a square…

A: Solution: Given: D = 4 in Area of circular section: A=π4×42=12.56 in2 Section modulus of circular…

Q: Consider flow from a water reservoir through a circular hole of diameter D = 0.16m at the sidewall…

A: Given data Diameter of hole D = 0.16m Vertical distance of sidewall from free surface = H = z1…

Q: H.W2 Determine the maximum deflection of the simply supported beam. E = 200 GPa and I = 39.9(106)…

Q: Structural analysis 2 (1401303) HWs Question For structure below, complete the missing loading and…

A: solution 1. Fixed end moment -MFAB = + MFBA = wl8 = 36 × 88 = 36 KN-m-MFBC = + MFCB = wl212 = 6 ×…

Q: In fig. FV = Water ---- -? If the tank width is 5 m (into the paper) 4m 5m C 5m B 1941.6 N 1941600…

A: To find out the vertical force if the tank width is 5 m.

Q: a solid circular shaft having a meter of 150 mm? ect one: a. 49.70 x 10-5 m4 O b. 49.70 x 10-6 m4 O…

A: To find the polar moment of inertia (Jz)-

Q: Analyze the given frame. P units in kN/m P 3m P 5m 4m pin 0.7P 4m

Q: Problem 2: It is recommended to change the circular cross section shown in the figure by a square…

Q: 1.0 m 3.0 m C 3.0 m B 1.50 m

Q: A saturated chunk of soil has a mass of 53.27 kg, a volume of 0.0300 m² and a water content of…

A: Given data : The value of water content w=40.4100=0.404 The value of mass of saturated soil m=53.27…

Q: A 6.4 mm diameter cylindrical rod fabricated form 1045 steel is subjected to fully reversed…

A: Given Data diameter = 6.4mm Compressive load = 10300n

Q: 1-An inward flow reaction turbine has external The turbine is running at 200 rpm e tangent of the…

Q: wo grade lines, SE and EA, having a slope of +4.5% and -2.8% respectively intersec at point E. Given…

Q: Determine the moments at all supports. 10 kN 12 kN•m A B 4 m 2EI 4 m 3EI 6 m 4 kN/m C

Q: Determine the maximum tensile and compressive bending stress developed in the beam.

A: Bending stress: - It is defined as the normal stress induced when external load applied to object…

Q: A simply supported beam with length of 5 Meters is loaded with a counterclockwise couple of 5 KN.M…

A: Simply supported beam is a determinate structure with one end hinged and other end roller supported.…

Q: mo

Q: Solve the problem using Moment -Area Method Problem I. The beam has a loose fit built-in support at…

A: Solution-Consider the diagram is shown below,…

Q: For the beam and loading shown below, determine the beam deflection at point H. Assume that El = 5.5…

A: Given data:- EI=5.5×104 kN-m2 The apply load on a beam, w=4.5 kN-m-1 The length of AB=3.3 m The…

Q: Find the flow for a rectangular channel, 5 m wide for uniform at depth of 2 m. The channel has a…

Q: A 6.4 mm diameter cylindrical rod fabricated form 1045 steel is subjected to fully reversed…

A: It is given that :

Q: Determine and draw the shear and moment diagram of the beam shown. Show complete solutions.

Q: estimate the volume of soil that fill the pot and the volume of material that was used to make the…

A: The values and diagram given in the question are as follows:

Q: What is the maximum and average shear stress of a given cross-section having les are diagonal "a"…

A: This question is related to the Strength of Material.

Q: for each curve. The beginning point is at sta 0+000. Using these data, make necessary computations…

Q: Find the tension in the Active tension bracing in the center bay (hint: again, there is no need to…

Q: = An equal-tangent crest vertical curve with a length L unknown, has an initial grade is G₁ +2.5%…

A: G1 = 2.5% G2 = -1%

Q: 4. Find the value of Mu required to use in strength design. The moment loads obtained there on are…

Q: 4. A building 38m X 45m is to be laid out with a 50m long metallic tape. If during standardization…

Q: Use the moment-area method to determine the slopes and deflection at point B and D of the beam.…

Q: Problem Number 2: Determine the Moment of Inertia, I, & I, and the radius of Gyration r, & ry. Y…

Q: Determine the moments at all supports.

A: ###Determination of all Support reaction ###

Q: 4: Design a lagoon treatmer OD of 2500 mg/L, influent wa urface loading rate of 30

Q: Distinguish between painting and electroplating in trying to minimize corrosion .

A: Electroplating and painting both are the methods of metal protection from corrosion . Both have…

Concept explainers

Alloys

An alloy is an admixture of two or more metals or a metal and a non-metal. Since ancient times, man has been using alloys. Alloying helps to retain the properties of the parent matter, such as hardness, strength, toughness, ductility and is corrosion-resistant. Copper alloys such as brass have antimicrobial properties that help to fight against (Coronavirus disease 2019) COVID-19 and other hospital-acquired infections. Some common alloys are brass, bronze, solder steel, etc. Most alloys have a lower melting point than their constituents. This is due to the presence of a nonmetal as one of the constituents that behaves as an impurity and restricts the raise of melting point.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

the center of part A measured from x-axis is (mm) - 400 mm- 50 mm 200 mm 50 mm 50 mm Select one: О 225 O 100 О 25 O None
Compute the coordinates of the centroid (,) of the area shown. Also compute the area moment of intertia about the z' axis that passes through the centroid. 2013 Michael Swanbom лу b с d ©ci❀O BY NC SA k *b*c Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 12 mm 7 mm 7 mm 19 mm The coordinate of the centroid is The y coordinate of the centroid is The moment of inertia about the z' axis going through the centroid is I₂' = a d с mm. mm. x mm4.
PROBLEM The centroid of the T-section shown is 2.9 inches above the base and x is 11. What should be the value of b to satisfy this condition? Input values in two (2) decimal places only without the unit. 1" x"
don't answer the X figure, just answer the d and e
Q2:- Locate the centroid (x, y) of the rode shown in the figure below. y -3 cm3 cm 4 cm 1 2 4 3 -r= 2 cm -X
e2 a h a The profile above depicts two joined profiles, each of width h. Find the centroid, X, of the total profile given that a = 145 (mm) h = 10 (mm) ts.) What is X;? (The gi component of the centroid, in mm) What is X2? (The e2 component of the centroid, in mm)
Plate A is situated in a coordinate plane as shown. The diameter of the plate is 20mm while its centroid is located at (90mm, 8mm). The radius of gyration of B with respect to the x-axis is (in 2 decimal places): kx || = +y mm B +x
The centroid of the T-section shown is 2.96 inches above the base. What should be the value of b to satisfy this condition? 1" 8" 1" Round off to 2 decimal places Answer in inches 11
The net area in tension, Ant, of the L6 x 6x 3/8 angle shown in the figure is equal to:
5) In the section of the figure below, 6 rebars 36 are used as tensile steel and 4 rebars number 20 are used as compressive steels. Assuming d' is 60 mm and fy is 400 MPa, calculate the anchor of the ultimate cross-sectional strength. 800mm 150mm 750mm 700mm O O 300mm (If there is a lack of problem information for the numerical solution section, make a logical assumption and write it down) The answer must be typed, avoid handwriting. The answer should be short and completely correct, l give a negative score to the answer that I feel is wrong; so please be careful, thank you.
a) For the solid section shown in Figure Q1, determine dimensions a, b and c. b) Determine the centroid position (x, y) for the solid section shown in Figure Q1 relative to the origin O on the x-y axes. Clearly show the breakdown of the section into areas used in your calculations. y 85 mm 53 mm b 25 mm 157° 25 mm 65 mm Figure Q1 (Not to scale) X
Determine the x and y-coordinate of the centroid shown below.