You were working as an electrician and a large steel manufacturing plant and you are in the process of doing preventive maintenance on a large DC generator you have Meg both a series and shot field warnings and found out each has over 10 and resistance to grow your own meter however indicator resistance of 1.5 resistance across terminals S1 and S2. The ohmmeter indicates a resistance of 2 to 5 resistance between terminals F1 and F2 are these readings normal for this type of machine

You were working as an electrician and a large steel manufacturing plant and you are in the process of doing preventive maintenance on a large DC generator you have Meg both a series and shot field warnings and found out each has over 10 and resistance to grow your own meter however indicator resistance of 1.5 resistance across terminals S1 and S2. The ohmmeter indicates a resistance of 2 to 5 resistance between terminals F1 and F2 are these readings normal for this type of machine

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

Which of the following is NOT a variable in voltametric methods? A. How the current is applied B. How the potential is applied C. The inclusion of convection D. All the above E. Type of working electrode
If PMMC meter have internal resistance of 1002 and full-scale range of 1mA. Assume we wish to increase the meter range to 2A. the value of shunt resistor will be: OR_sh=0.00500 OR_sh= 0.00010 OR_sh=0.11111 0
it is the ratio of measured voltage to the measured current of an electrical load circuit. A. Resistance B. Hot resisitance C. Cold resistance D. infinite Resistance
A snubber circuit has snubber time constant (10 msec), voltage source (10 kV), discharge current of the Thyristor (5 µA) and frequency (50 Hz). Find the rate of voltage changing with time and snubber circuit power losses?
b) A certain winding made up of copper has a resistance of 100 Q at room temperature. If resistance temperature coefficient of copper at 0 C° is 0.00428/C°, calculate the winding resistance if temperature is increased to 45 C°. Assume room temperature as 25 C°.
An AC ammeter is connected in series with the primary winding of T1. What is the expected current reading? An AC ammeter is connected in series with the secondary winding of T1. What is the expected current reading? An AC ammeter is connected in series with R1. What is the expected current reading? NOTE: Idc for HW rectifier = 0.318 * Ipeak = 0.45 * Irms Describe/Explain briefly the purpose/use of the array (series-parallel) connection of the rectifier diodes in the given circuit.
3. The figure on the left below shows a schematic diagram of a battery. The voltage measured by U1 is called the terminal voltage given R1 = 1 ohm. In the figure on the right below, the terminal voltage of each of the battery-resistor combination is Vr = 1.5 volts. Find the following: a. The current passing through R5. b. The currents passing through R1 and R3 C. The voltage across R1. d. The voltage of the battery EMF. e. The percentage of voltage loss ot the battery due to the internal resistance R1. The power dissipated by the internal resistance R1. g. The power dissipated by R5 if R1 = R2 = R3 = R4 = 0. h. The percentage of power dissipation loss due to the four resistors R1, R2, R3, and R4 f. R1 R3 S10 R1 U1 1.500 EMF EMF R5 100 V1 R2 $10 EMF R4 EMF EMF
Find the current in the given figure. Let R₁ = 2 ohm, R2 = 3 ohm, R3 = 6 ohm, and Va = 12V. Will rate! Please answer in typing format
We want to make a resistivity measurement. How should we connect the probes of the multimeter? Drag the connector images to the correct locations and "Not Connected" images to the rest. SLIDE SWITCH: LEFT- OFF MIDDLE- DC VVOLTS DC mA NUMERICAL VALUE OF VOLTS OR MA OR OHMS DISPLAYED HERE 0.00 OHMS FIGHT - AC VOLTS AC mA OFFOO AC DC-n DM 8010 MOVE ROTARY SWITCH TO THIS AREA TO READ OHMS (SELECT RANGE) 1000 200 20 MOVE ROTARY SWITCH TO THIS AREA TO READ VOLTS (SELECT RANGE) 20 200 2K 20K. 200 200K 2M 20M MOVE ROTARY SWITCH TO THIS AREA TO READ mA (SELECT RANGE) *20u 200u 200m 20m 10A mA COM PROBES Windows'u Etkinleştir Windows'u etkinleştirmek için Ayarlar'a gidin NOT CONNECTED
Need help with finding paramters
In the figure R₁-3.41R, the ammeter resistance is zero, and the battery is ideal. What multiple of e/R gives the current in the ammeter? EH Number Units *E/R
leaving a freevway. Current from the opposite side must travel further, weakening the potential on that side. This creates a potent the motor in that direction, causing the motor to spin. O Only the side where the switch is closed forms a cormplete circuit, so the motor must spin in that direction. Answer the questions and submit the photos for questions 2 -9using the circuit from STEP 2. D2 Yellow R1 50 Q R2 50 0 R3 PSB (+ 5 V 100 aLW R4 D1 100 Q Blue SW1 Sw2 Question 2 本