You have a circuit with two resistors (0.1 MQ and 0.2 MQ) in series with a 30 V DC supply. (a) Using Ohm's law, calculate the theoretical voltage drop (without loading error) across the 0.2 M2 resistor. (b) What would the measured voltage across the 0.2 MQ resistor be using a voltage meter with an internal resistance of 250 MQ? (c) What would the measured voltage across the 0.2MN resistor be using a voltage meter with an internal resistance of 1,000 MQ? (d) Calculate the percentage loading error for parts b and c.

You have a circuit with two resistors (0.1 MQ and 0.2 MQ) in series with a 30 V DC supply. (a) Using Ohm's law, calculate the theoretical voltage drop (without loading error) across the 0.2 M2 resistor. (b) What would the measured voltage across the 0.2 MQ resistor be using a voltage meter with an internal resistance of 250 MQ? (c) What would the measured voltage across the 0.2MN resistor be using a voltage meter with an internal resistance of 1,000 MQ? (d) Calculate the percentage loading error for parts b and c.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 250 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance?
3 A peak rectifier (peak tollower) Cir cuit is gian below. Vs is a GOH3 Sinuscidal Vollge with peak value Upz50V. 50V. The load resistance R= Sk . Find the Vallke of the capacitance C Such that the peak- to-peak ripple 2 volts. (idenl diede) Voltage Vr Vs
The volt–ampere characteristic of a certain two-terminal device is a straight line that passes through the points (2 V, 5 mA) and (3 V, 15 mA). The current reference points into the positive reference for the voltage. Determine the equivalent circuit for this device.
The Figure 2 shows an electronic circuit designed for supplying power to a load (R1). The supply voltage 235V (RMS, AC) at frequency of 50HZ. The required DC voltage and power for the load are 24V and 3.6 W respectively. The Electrical Components of this AC to DC converter are: A full-wave rectifier to convert AC voltage to DC voltage. A regulator with transistor and Zener diode to ensure a constant voltage and power for the load. D1 Iide 91 Vaut VLoad D2 D3 Vde VI sine R1 RL Regulate Reetifier Figure 2. Complete Circuit Assume that the diodes are real diodes (NOT ideal diodes). The following information is available: The collector to base resistor of the regulator R1 = 5.0 k The transistor Q1 with B value of 24 is used for the regulator circuit. Determine the following quantities for this electronic device and fill the table below: Question Answer The voltage of Zener Diode (Vz) The current in R1 The DC current into the regulator | (Idc) Base current of transistor (IB) Collector…
A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 250 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance? If a full-wave rectifier is needed?
A R-load half-wave rectifier used sinusoidal voltage source with a peak value (35.353kV). The firing angle is (30). The total resistance is 50k2 and frequency is 50HZ. Calculate (in details): load direct voltage, maximum direct voltage, normalized voltage and effective voltage, power delivered to the load, power factor, form factor, ripple factor?
Design a Zener diode circuit to regulate a source voltage that can vary from 9 VDC to 17 VDC, has a load current that can vary from 0 mA to 500 mA to generate a constant load voltage of 5 VDC. Draw the complete circuit with all values, determine the largest value of the inline source resistance (Rs), and determine the Zener diode's max power dissipated. Pzmax = Rsmax =
Three-phase half wave rectifier supply resistive load with DC power of 4 kW; the ammeter connected with D1 indicates 8 A r.m.s current, and the source frequency is 50 Hz Due to system inductance the average voltage drops to 96.2% of idealized value ( when the inductance is neglected). How much will the average and r.m.s voltage s be? The r.m.s phase current and average load current Is=? & Idc=? The secondary r.m.s voltage and transformer capacity Vs & KVA? The inductances causes the voltage drop Lc=? The diode forward current and maximum inverse voltage? Now, if the phase B is failed ( disconnected), how much with new dc voltage be in %..Vdc=….% ??
Create a circuit design that will supply an output voltage of 2VDC, having a 6V DC source supply, using a resistor and a diodes. Current that is flowing on the circuit should be 20mA. It will be used as power source for a small project. (With solution)
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
Vps = 10 V R = 0.1k02 ww -ovo R₁. Consider the Zener diode circuit shown in figure. The Zener diode voltage is Vz= 5.8V at Iz= 10mA and the Zener resistance is rz = 200. a) Find the output voltage for RL = 1k0 b) Find the change in the output voltage when the load resistance varies +ARL.
please give detail explain.. Ans : Rth = 28 ohm Vth = 92 V