11 13.13 - Thermal Expansion of Solidsand LiquidsYou are looking to purchase a small piece of land in HongKong. The price is "only" $65,000 per square meter! Theland title says the dimensions are 24 m x 28 m. By howmuch would the total price change if you measured theparcel with a steel tape measure on a day when thetemperature was 20°C above normal? (Assume that thedimensions of the land do not change with temperature.)(You do not need to enter any units.)$ 96.73When calculating the change in area, make sure to havemore significant figures for the new length/width thanthe desired final answer. For example, if the answerrequires 3 significant figures, then the new length/widthmust have at least 4. In some cases, you may needmore than 4.Does the buyer has to pay more or less when thetemperature was 20°C above normal?morelessIncorrect. Tries 6/10 Previous TriesSubmit Answer

Given data as per question Rate of land per square meter area =$65000 Dimensions of the land = 24 m…

You are looking to purchase a small piece of land in Hong Kong. The price is "only" $65,000 per square meter! The land title says the dimensions are 24 m x 28 m. By how much would the total price change if you measured the parcel with a steel tape measure on a day when the temperature was 20°C above normal? (Assume that the dimensions of the land do not change with temperature.) (You do not need to enter any units.)

You are looking to purchase a small piece of land in Hong Kong. The price is "only" $65,000 per square meter! The land title says the dimensions are 24 m x 28 m. By how much would the total price change if you measured the parcel with a steel tape measure on a day when the temperature was 20°C above normal? (Assume that the dimensions of the land do not change with temperature.) (You do not need to enter any units.)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1 The 45° strain rosette is mounted on a surface of the bracket as shown in Figure Ql. The bracket is made from steel with Eseel = 120 GPa and poison ratio, v = 0.28. The following readings are obtained for each gauge under loadings: Ea=[X+Y] (10*) Es = -200(10-6) E= -180(106) Important note : X=100 Y=60 (a) Prove that &=Ea and &= E,. (b) Determine the shear strain, y and the normal strain, &, and E,. (c) Estimate the in-plane principal strains and the angle associated with the principal strains, and
What is the normal force applied to the block?
part ii
e?Y dx sin?x cos 3y oy
d C b ta ➤
8 the ban
(b) A differential element on the bracket as shown in Figure 1 is subjected to plane strain that has the following components: ex = 150µ, ey = 200µ, yxy = -700µ. By using the strain transformation equations, determine: - (i) The equivalent in-plane strains on an element oriented at an angle 0 = 60° counterclockwise from the original position. (ii) Sketch the deformed element within the x' – y' plane due to these strains. (iii) The stresses on the oriented planes in (I) where the value of elasticity, E = 200 GPa and Poisson's ratio, v = 0.32. (iv) Give your comments on those stresses in (iii) in terms of elastic limit/failure if the material's yield strength in tension/compression is 250 MPa and in shear is 90 MPa.
what is "p"? in the work formula
Q/ Correct the under line words 14. Al-4%. Mg alloys are produced by extrusion because has high strength 15. Mg -Zn - Zr alloy is not proper to produce by extrusion because of susceptible to micro porosity and can be used for casting process 16. Brass-alloys are expensive because of difficulties experienced of its casting 17. The density, T.S. and hardness of Fe alloys can be decreased by working
_% od 25m is 9m
19) During the Vicker harness experiment, it is found that the diameter of indenter is larger than indentation diameter. Select one: True False
120 mm 600 mm 10-N 4N 600 mm 4N