You are given an unknown op amp and asked to estimate its gain-bandwidth product. To do this, you use a non-inverting amplifier configuration to measure the gain at several frequencies: • At f = 25 kHz you measure the gain to be 70.5 V/V • At f = 50 kHz you measure the gain to be 47.2 V/V At f = 100 kHz you measured the gain to be 26.3 V/V What is the GBW of this op amp?

You are given an unknown op amp and asked to estimate its gain-bandwidth product. To do this, you use a non-inverting amplifier configuration to measure the gain at several frequencies: • At f = 25 kHz you measure the gain to be 70.5 V/V • At f = 50 kHz you measure the gain to be 47.2 V/V At f = 100 kHz you measured the gain to be 26.3 V/V What is the GBW of this op amp?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

Question: The circuit below, Figure 1, shows an amplifier with a diode in the feedback. The amplifier can be considered to be ideal. The diode has a threshold voltage of 0.6 V. The values for the components are R1 is 1 k0, R2 = R3 = 9 k. Determine the transfer function of this circuit. Vin ww R1 R2 www R3 741 D1 Vout
For the given op-amp circuit, determine: in/ls, Vout/in, and Vout/Is. RI iin Is Vout RL ZinCL) Zout(CL) For the op-amp: AVOL=2000, Rin=100KN, Rout-502 Rs-502, RI-5002, RL=1002
R, V OUT Let currents and node voltage for the Op-Amp circuit be defined as follows: |1 equals the current flowing through Rin from left to right. Let Vb be the voltage at the inverting input (-). Write 1 in terms of the node voltages Vin, Vb (voltage at inverting input). O Vb - Vin O Vvin - Vb O (Vb - Vin)/Rin O Vin - Vb) / Rin O - Vin/Rin
In current summing, the summing network is connected in to the input. * None of the choices both a and b series can't determine All of the choices parallel -14 dB/octave means * None of the choices A reduction of op-amp's voltage gain by a factor of five each time the frequency double. All of the choices A reduction of op-amp's voltage gain by a factor of three each time the frequency double. A reduction of op-amp's voltage gain by a factor of two each time the frequency double. A reduction of op-amp's voltage gain by a factor of four each time the frequency double. An increase of op-amp's voltage gain by a factor of four each time the frequency double. Created by SEASOFT LTD.
From the figure , write note voltage equations, one for each input terminal of the op amp The expression for the load current ( iL) can be written as a function of the input voltage (Vin) and the load voltage (VL) IL =A(Vin) + B(VL) b.1 What is the expression for A? b.2 What should be the condition for R1 R2 R3 R4 so that B is zero? (NB this will make( iL) depend only on Vin and not on RL)
1. Determine the CMRR and express it in decibels for an amplifier with a differential voltage of 8500 and a common-mode gain of 0.25. 2. Determine the CMRR and express it in dB for an op-amp with an open-loop differential voltage gain of 85,000 and a common-mode gain of 0.25. 3. When a pulse is applied to an op-amp, the output voltage goes from -8 V to +7 V in 0.75 µs. What is the slew rate? 4. Differentiate the working principle of differential and operational amplifier and its operation. Discuss your answer in at least 5 sentences.
Given a range of values for vs and v0, how are these calculated for v0 and how is the range for vs made to avoid op-amp saturation if it is -2 V < vs < 3 V? vs(v) 0.4 2.0 3.5 -0.6 -1.6 -2.4 vo(v) -2 -10 -15 3 8 10
- V2 15Vdo 3 U1A R1 2 1k V- LM324 1k V3 15Vde | VOFF = 0 VAMPL = 1 FREQ = 2k AC = 0 0. R2 Figure 4. Operational amplifier circuit. What frequency does the output voltage (across R3) have? What is the amplitude of the output voltage? From the output waveform and the input waveform, determine the gain of the op-amp circuit. Does this match with what you predicted? How could you change this circuit so that the output voltage would be nearly the same as the input voltage? What purpose would that serve? Can you modify the existing circuit and verify this experimentally? What is the phase difference between the output and input voltage? Derive the transfer function for the output-input relationship for the operational amplifier. How would the gain and the output change if a capacitor were in the feedback path instead of a resistor? (Examine the circuit using phasors and impedance and circuit analysis techniques). -w-
The input voltages of an op-amp are v_{2} = 1005mu*V and v_{1} = 995mu*V The op-amp parameters are CMRR=100 dB A_{d} = 2 * 10 ^ 5 Determine the output voltage vo. a. 3.212 V b. 2.922 V c. 2.620 V d. 1.120 V e. 2.002 V(NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE).
Assume that Op-Amp as shown above is ideal. Given that R1 is 0.29 Ohm, R2 is 1.7 Ohm, R3 is 2.03 Ohm, R4 is 2.125 Ohm. Calculate Vo?
A 741-type op-amp has a gain-bandwidth product of 1 MHz. A non-inverting amplifier using this op-amp and having a voltage gain of 20 dB will exhibit a -3 dB bandwidth of Show solution on your answer sheet. O 100 kHz O 50 kHz O 1000 / 7.07 kHz O 1M Hz
For the op-amp shown in the following figure, the midrange voltage gain is equal to- 3 kn V₂ VM Select one O a-26.7 Ob.-27.7 c277 d. 26.7 80 kf www