You are given a network layout below and asked to prepare the ROUTING TABLE for the ROUTER 3 only. Assume, all network communication lines are open. In your R3 Routing table, write all four destination IP addresses and corresponding interface numbers. In your answer use the notation of 12.34.56.xx4 (which means if the fnal destination is 1234.56x, then use the interface 4) 10.10.51 x R1 10.10.53.x 10,10.70x 10.10.34.x R4

You are given a network layout below and asked to prepare the ROUTING TABLE for the ROUTER 3 only. Assume, all network communication lines are open. In your R3 Routing table, write all four destination IP addresses and corresponding interface numbers. In your answer use the notation of 12.34.56.xx4 (which means if the fnal destination is 1234.56x, then use the interface 4) 10.10.51 x R1 10.10.53.x 10,10.70x 10.10.34.x R4

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Suppose a router has built up the routing table shown in Table 3.19. The router can deliver packets directly over interfaces 0 and 1, or it can forward packets to routers R2, R3, or R4. Assume the router does the longest prefix match. Describe what the router does with a packet addressed to each of the following destinations: (a) 128.96.171.92 (b) 128.96.167.151 (c) 128.96.163.151 (d) 128.96.169.192 (e) 128.96.165.121 Table 3.19 Routing Table for Exercise 56 SubnetNumber 128.96.170.0 128.96.168.0 128.96.166.0 128.96.164.0 (default) SubnetMask 255.255.254.0 255.255.254.0 255.255.254.0 255.255.252.0 NextHop Interface 0 Interface 1 R2 R3 R4
The subnet 222. 20.128.0/20 is allocated to an organization that has 4 departments, show how to subnet this network to 4 independents networks. Give the IP address of each subnet in binary and in dotted decimal notation (a.b.c.d/x) (show your steps, only final answer not accepted).
Suppose you have the following network requirements, for Given an IP address and mask of 9.0.0.0/8, design an IP addressing scheme using VLSM? How is the efficiency of this method achieved? Use the topology in Figure to answer the questions. a. Network 1 needs to support 330 host addresses. b. Network 2 needs to support 62 host addresses. c. Network 3 needs to support 2 host addresses. d. Network 4 needs to support 520 host addresses. e. Network 5 needs to support 230 host addresses. f. Network 6 needs to support 62 host addresses. g. Network 7 needs to support 2 host addresses. h. Network 8 needs to support 2 host addresses.
Let IP address 200.210.56.76/28 determine the subnet mask, subnet id, broadcast address, and total number of subnets and hosts in subnets. And use a nice illustration to demonstrate Remote monitoring.
A IPV6 global unicast address is composed of a Global Routing prefix = 2001:0540:FACE, Subnet ID = 0020, and an interface id = 0000:0000:0000:0040. Assuming the IPV6 global unicast address follows the "3+1+4" Rule, which of the following is the correct IPV6 global unicast address representation? %3D %3D 2001:540:FACE:20:40/32 2001:540:FACE:20:40/64 2001:540:FACE::40:20/32 2001:540:FACE::40:20/64
An IP address can be written as a 32-bit number. For a class B network, the two most significant bits are set to 10. The 16 most significant bits are used as a network ID, and the 16 least significant bits are used as a host ID. However, the host ID cannot be all O's or all 1's. How many hosts (i.e., host IDs) can there be on a class B network? Type your answer.
Consider the LAN below consisting of 12 computers (A-L) connected by two Ethernet bridges. At t=0 the bridging table entries for both bridges are empty. At t = 1, node L sends to node E, and node E replies immediately (well before the next time step). What are the (MAC address, interface) entries in the bridging tables right after these transmissions? Note: interface = port number a) Left-hand-side bridge: (L,15), (E, 8). Right-hand-side bridge: (L,7), (E, 5). b) Left-hand-side bridge: (L,8), (E, 8). Right-hand-side bridge: (L,7), (E, 7). c) Left-hand-side bridge: (L,15), (E,5). Right-hand-side bridge: (L,7), (E, 8). d) Left-hand-side bridge: (L,8), (E,8). Right-hand-side bridge: (L,7), (E, 7).
Please idk if i got this right
15. Consider the following plot of TCP window size as a function of time (y axis is the congestion window size (segments), and x axis is the transmission round). Assuming that TCP Reno is the protocol experiencing the behavior shown above, answer the following questions. 18 16 14 12 10 00 8 6 4 2 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1) Identify the intervals of time when TCP slow start is operating. 2) After the 5th transmission round, is segment loss detected by a triple duplicate ACK or by a timeout? 3) What is the value of Threshold at the 7th transmission round? 4) What is the value of Threshold at the 15th transmission round?
We have an IP address of 100.120.142.34/20 Assuming that the network router is assigned the largest IP address in the range, what is the IP address of the router?
List all the static routes on each of the 4 routers required for full communication across the topology. The addresses with question marks have been relabeled. I think each router should have 3 static routes. This is using the ip route command (ip route <netid> <net mask> <next hop>)
Read the manual page of arp command, give the complete command line to add an entry to ARP table for network interface eth1 that maps IP address 192.168.2.45 to MAC address 08:01:23:b2:a0:9d, and then the complete command line to delete this entry.