B7 5.Why are there so many different units for measuring pressure?6.What does the viscosity rating of a motor oil indicate?

For the sake of convenience, several units are used to represent the wide range of pressures that…

Answered: y are there so many different units for…

Engineering

Mechanical Engineering

y are there so many different units for measuring pre

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter8: Preventive Maintenance And Basic Services

Section: Chapter Questions

Problem 20RQ: True or False? An oil with the classification of 5W-30 has the viscosity of both a 5- and 30-weight...

See similar textbooks

Related questions

Q: draw the isometric and pictorial figure of the given measurement below

Q: If the gage reading at (A) is (pA=1OkPa), find the gage reading at (B) in (Pa) and in (mm Hg)?…

A: Write the given values with suitable variables. PA=10 kPa Consider, a reference line of the…

Q: Dimension is 3/4” scale is 2”=1” what is the distance?

Q: What are the two most common systems of units?

A: Given Data⇒ systems of units Problem statement⇒ Problem says What are the two most common systems of…

Q: 9/16 inch is approximately equivalent to . mm. 19 17 14 12

A: The dial indicator is a traditional mechanical kind with a dial display that resembles a clock face…

Q: Enumerate the remaining measurement quantity and Unit

A: Time-si unit second, length-si unit meter, mass-si unit kilogram, electric current-si unit…

Q: H. What scale is used if a line 84 mm long represents a fence 63 m long?

A: Given:- Scale length = 84 mm Actual length = 63 m = 63000 mm To Find:- Scale

Q: Use prefix multipliers to express each measurement without any exponents. 55.2 x 10-10 s

Q: Define Some basic pressure gages.

A: The pressure gauges are broadly classified into three types: Hydrostatic Gauges Aneroid Gauges…

Q: Question 10 The primary unit of measurement for engineering drawings is? Select one: O A. Metre B.…

A: Primary unit: The stocking unit that is used to measure the dimensions of any object in an…

Q: 20 30 R15 5-Ø10 R10 Ø40 10 40 40 Figure 1

Q: traight to the point. How far was he originally from the point, and how far did he travel in…

A: Hunter is at point A and desired to go to point P. He travelled half due east and turns 120° left.…

Q: The length of a pencil is measured with two rulers. Report the length of the pencil from cach ruler…

A: The length of the pencil is measured with two rulers :-

Q: Show a scale diagram indicating a reading of 0.206 inch in a micrometer.

A: Given question : Show a scale diagram indicating a reading of 0.206 inch in a micrometer. The…

Q: There are some special gauges used in measurements. For the following special gauges listed below;…

A: A drill gauge may be a device utilized to distinguish the size of a drill bit. It can be made…

Q: Can you put all the measurements, as in all measurements and make it in centimeters?

A: given : Isometric view

Q: 2. One of the following is suited to the measurement of small, processed parts and similar items: A.…

Q: Discuss the measurement methods (at least two) used in the industries for the following iii)…

A: The viscosity of the fluid is a very important property. It is defined as the ability to resist the…

Q: G. A line 32 mm long joins to towns on a map of scale 1:100,000. (a) How far apart are the towns to…

A: For solution refer below images.

Q: Using only Table A (Conversion of Units), calculate the values asked. All answers must be given…

Q: Use prefix multipliers to express each measurement without any exponents. 87.9 x 10-L

A: Given: The expression is 87.9×10-7 The scientific notification for the expression is, 87.9×10-7…

Q: Use prefix multipliers to express each measurement without any exponents. 23.4 X 10-11 m

A: The measurement is written as, scientific notation:23.4×10-11 mIt is written as,23.4×10-11…

Q: The median value of the following set of measurements is Answer 33, 34, 33.5,35,34.5,36

A: Solution: Median value can be obtained by arranging the given values in ascending order. Therefore…

Q: What is the height if the dimension figures written on the dimension line? a) 7mm to 9mm b) 2mm to…

A: Answer: d Explanation: It is customary to write the figures with a height of 3mm to 5mm.

Q: Sketch a meat tenderizer mallet. And can you show me the measurement of it.

Q: 30 mm Sym. 15 mm 50 mm

A: we have to locate the centroid of the shape.

Q: y. what is the change in length in mm? k for =

A: Need to find change in length.

Q: II. Comprehensive questions. 1. Explain the meaning of the following annotations, the tolerance…

A: For solution refer below images.

Q: EH, FG, EG and GH. 10KN 4m 3m 3m 20 kN 3m 3m 30KN 3m 3m

Q: A slip gauge setting height of 63.205mm is observed and an angle of 40° is found during the precise…

Q: The least count of the main scale of a screw gauge is The minimum number of divisions on its…

A: As per bartleby guidelines we are allowed to solve only 1st question if multiple questions are…

Q: it indicates the difference between the absolute pressure of the system and the absolute pressure of…

A: the difference between the absolute pressure of the system and the absolute pressure of the…

Q: Look up the measurement of the approximate thickness of a human hair. Convert the measurement to an…

A: Human hair is approximately 17 to 181-micron meter

Q: 6. On an engineering drawing a dimension is laid out as 1.760 ± 0.005 A note on the drawing states…

A: (a) The nominal dimension = 1.760 inches. (b) The upper limit = 1.765 inches. (c) The tolerance = ±…

Q: the minimum metric

A: Given; For the three bolt system shown in the figure,shear yield strength=200 MPaFOS=2The min.…

Q: Using only Table A (Conversion of Units), calculate the values asked. All answers must be given…

Q: Use prefix multipliers to express each measurement without any exponents. 38.8 x 10° g

A: Given: The measurement is m=38.8×105 g. The unit conversion factor to convert Gram into Megagram is,…

Q: A ruler used to measure a penny has markings every 1 mm. Which for the size of the penny is…

A: Ans. (c) 19.1mm

Q: 7. is used for measuring the wind direction.

A: To find : which instrument is used to measure the wind direction

Q: The vernier caliper is a direct measurement device with a least count of 0.02 mm and has 50…

A: Vernier caliper is invented by Pierre Vernier in 1631. Vernier caliper is the measuring device that…

Q: II- Write the subdivision of standards and briefly define each of them;

A: Standards can be classified into following categories - Primary Standard - These are carefully…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

5.
Why are there so many different units for measuring pressure?
6.
What does the viscosity rating of a motor oil indicate?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Typically during a pressure test, the pressure should not drop more than_____ psi between shifts.
Which of the following statements DOES NOT describe a fluid? a.lt stays in a constant shape upon application of constant shear stress. b.It has medium to negligible intermolecular attraction. c.It takes the shape of its container. d.It does not have a final deformed state. Which of the following is TRUE regarding fluid viscosity? a. An ideal fluid has infinite viscosity. b.A fluid's kinematic viscosity on earth is the same as its kinematic viscosity on the moon. c.A Newtonian fluid's viscosity is constant for any magnitude of shear stress. d.Under constant shear stress, a fluid with higher viscosity has a higher rate of deformation. Determine the pressure increase that must be applied to 400 L of gasoline (K=1.3GPa) to reduce it to 370 L. a.78.0 MPa b.165 MPa c.105.4 MPa d.97.5 MPa The pressure of air above an oil (s=0.80) surface in a closed tank is 120 kPa. The pressure 3 m below the oil surface in kPa is: a.149.43 b.143.544 c.138.544 d.23.644
Unit of kinematic viscosity?
The rate of change of viscosity with temperature is known as viscosity index and high viscosity index means oil will remain the same over a wide range of temperatures, Select one: True False
The rate of change of viscosity with temperature is known as viscosity index and low viscosity index means oil will remain the same over a wide range of temperatures, Select one: True False
Given two oil According to the standard by Society Automotive Engineers the oil , by comparing the 5W-30 with the 10W-30, a. The 5W-30 has lower viscosity than 10W-30 at low temperature. O b. The 5W-30 has higher viscosity at the high temperature. c. Both of the oils are suitable for cold weather O d. All of the above are true.
True or False? An oil with the classification of 5W-30 has the viscosity of both a 5- and 30-weight oil. The 5W means the oil has a viscosity of 5 when warm and a 30 rating when it is cold.
As the temperature of an oil sample decreases, A. the viscosity of the oil increases. B. the oil will flow better through oil lines and nozzles. C. the viscosity of the oil decreases. D. Both B and C are correct.
What is the relation between temperature and viscosity for hydraulic oil? a. temperature decreases viscosity decreases at atmospheric pressure b. none of the listed c. temperature and viscosity vary linearly d. temperature increases viscosity decreases at atmospheric pressure
As the temperature of the nitrogen gas increases of same gas increases. Viscosity Weight density Specific volume Density
Which one of the following is a wrong statement. Paint is a non-Newtonian fluid Water and air are Newtonian fluid The viscosity of any real fluid is zere The viscosity of an ideal fluid is zero
List five different types of oil rating systems