Dimension is 3/4” scale is 2”=1” what is the distance?

Q: Use Scale ( 1:1), for the front and side views shown draw the isometric projection 50 30 25 40 80 30…

A: Isometric projection of an object is defined as a method of representing a 3-dimensional object in a…

Q: On the attached drawing 11A005< what is dimension "G"

A:

Q: . a. On the part shown, show a angularity specification to orient the angled surface in relation to…

A:

Q: Enumerate the remaining measurement quantity and Unit

A: Time-si unit second, length-si unit meter, mass-si unit kilogram, electric current-si unit…

Q: Determine the x and y components of reaction at point A using scalar notation. Ax, Ay = ? lb B)…

A:

Q: 4. A Pelton turbine produces 8 MW of power under net head of 440 m. The turbine has two jets. The…

A:

Q: Using the diagram, determine the maximum diameter for DIA B.

A:

Q: Provide the sectional front view, looking at the direction X, draw the top view, and left-side view…

A: Find Sectional front view, top view side view, front view, and right side view.

Q: Use Scale ( 1:1 ), for the front and side views shown draw the isometric projection 50 30 25 40 80…

A: Isometric projection is the axonometric drawing in which the angle between each axis is 120 degrees.…

Q: The object shows the center of the whole is three inches from the left surface and one inch from the…

A: we have to determine what kind of dimensions are used in the hole

Q: If the main scale reading (mm) and vernier scale reading (division) are 27 and 47 respectively for a…

A: Given: main scale reading = 27mm vernier scale division = 47 division total division on vernier…

Q: Some necessary dimensions are dimensions that are missing. missing from the following 3-view…

A: According to the details provided in the three views of the drawing, there is a hole of 2 units in…

Q: Draw the SECTION VIEW with the scale 1:1 on the new drawing paper using all the method on section.…

A:

Q: .75 1.25 2.25 3.75-

A:

Q: ect with dimension. mode 50 R20 Ø20 25 15 Ø32 Ø60 80 45 50 60

A: According to the details provided in the question, we need to DRAW the half sectional view of the…

Q: 1st image : What is the reading on the micrometer? 2nd image : What is the reading on the…

A:

Q: 1ST Dimensions and projections

A: 1 st angle projection

Q: Use Scale ( 1:1 ), for the front and side views shown draw the isometric projection 50

A: In an isometric projection, every one of the three axis are thought to be divided at a angle 120…

Q: Draw the isometric projection of the object showing the top, front and right side.

A:

Q: Draw the plan, Front view and the Side view of the following figure and do the dimensioning.

A: Please refer the following orthographic views of the given object.

Q: Fill-up the blanks in the following sentences by appropriate words selected from the list of words…

A: As per the regulations of the Company, only three parts will be answered, and for rest of the parts…

Q: Draw Front View and Top View of the following component

A: Solution:

Q: Q15) The following figure represents one dimension measurement. a- What is the instrument used for…

A: (a) To write:  The name of instrument use in given figure. Explanation: Internal micrometer: A…

Q: Use the following isometric drawing of a hospital to create a two-point perspective drawing. (Use an…

A: Use the following isometric drawing of a hospital to create a two-point perspective drawing. (Use an…

Q: Using the Engineering Scale 1" = 20', what is the red dimension below to the nearest foot? 20 20 0 1…

A:

Q: make a three-view drawing, complete with dimensions, of the part. Show the dimensions with the view…

A: the given isometric view

Q: 2 2XRO 16 0.9 + 2.7 -2.2- -0.7-1 -1.25- ~IB 06 1.4 2,9 09 -1.6- SCALE: 1=1 SCALE: 1=2

A: Just mark all necessary dimension lines.

Q: Use Scale ( 1:1 ), for the front and side views shown draw the isometric projection 50 30 25 40 80…

A: Isometric projection of an object is defined as a method of representing a 3-dimensional object in a…

Q: 100 82 20 32 96 Top view Isometrie view

A: Top view Top view of object is obtained when we see object from top.   Front view Front view of…

Q: SECTION B: OPTION 1 Convert figure below into ISOMETRIC & Do not dimension the drawing. All units…

A: It is a view representation of a drawing in 3D view. Hence it can be executed by understanding the…

Q: R=200 30 240

A: Find the value of P and thetha.

Q: Draw Front and Side and top with all dimensions please

A: According to the question,A  3-D object is provide, we need to draw three projection views of the…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.