+ xj(1) x2(1) 1 N/m At) 1 kg 1 N-s/m 1 kg Frictionless' Figure John Wiley Sens. Inc. Allights reerved The transfer function where X1(s) is the output and the force F(s) is the input is X,(s) s? +1 а. Т(s) %3D S' +s +s+1 b. T(s)= X,(s) s² +s+1 4 F(s) s* + 2s' + 2s +s+1 X,(s) +s+1 c. T(s)= F(s) +2s + 2s² s' +s+1 X,(s) d. T(s)= F(s) 2s +2s + s+1 Select one: О а. b b. d С. С O d. a O O O O

+ xj(1) x2(1) 1 N/m At) 1 kg 1 N-s/m 1 kg Frictionless' Figure John Wiley Sens. Inc. Allights reerved The transfer function where X1(s) is the output and the force F(s) is the input is X,(s) s? +1 а. Т(s) %3D S' +s +s+1 b. T(s)= X,(s) s² +s+1 4 F(s) s* + 2s' + 2s +s+1 X,(s) +s+1 c. T(s)= F(s) +2s + 2s² s' +s+1 X,(s) d. T(s)= F(s) 2s +2s + s+1 Select one: О а. b b. d С. С O d. a O O O O

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A uniform bar AB weighing 424 kN, is fastened by a frictionless pin to a block weighing 200 kN as shown in figure below. At the vertical wall, f = 0.268 while under the block f = 0.20. Determine the force P needed to start the motion to the right.
Determine the force (written as a vector) which BC exerts on member AB (a) if the 800-N load is applied to the center of member AB, and (b) if the 800-N load is applied to the center of member BC. 800 N A 1.1 m 1.1 m B 32 L. Answer: (a) F -( i i+ i j)N (b) F-( i i+ i i) N
sF.ricylinder.rsh Tcy are the radius of shaft and inside radius of cylinder a P2.11 Consider a concentric shaft fixed axially and rotated inside K( cylinder.rsh.ľcy are the radius of shaft and inside_radius of cylinder respectively, with total length L. Let the rotational rate @ rad/s and applied torque be M .Using these parameters, a) Derive a theoretical relation for the viscosity u of the fluid between the shaft and cylinder. b) For a shaft of 8cm long, rotating at 1200 rev./min, with rsh = 2.00 cm and the measured torque is M viscosity? [µ = M(rcy=r sh)/(2nwr;,L)] %3D - 0.293 N.m. What is the fluid [µ=0.29 kg/m.s] rey:205 ( Coso 76 243.
The BC rod in the carrier system shown in the figure has a circular cross section. diameter 25 mm and Tensile Strength 210 MPa and Modulus of Elasticity 2x105 It is MPa. Since a load of 640 kg is hung on the D end of the system; For BC bar: a) Tensile stress, b) Safety coefficient, c) Calculate the length change amount.
Number 9
In 1, why if we separate the CD column, all the R1 force is in the column? But in 2, if we separate the CD column, half of the force F is in the column ...
In 1, why if we separate the CD column, all the R1 force is in the column? But in 2, if we separate the CD column, half of the force F is in the column ... #structure_analysis
statics of rigid bodies
ASAP ty
DETERMINE THE FORCE (Ib) IN MEMBER AB OF THE ROOF TRUSS SHOWN GIVEN THE DATA BELOW: F1=61 lb F2- 167 lb 0- 29 degree a 45 degree "Note: for compression, include.a negative sign (-) and for tension, type your answer as is. Input your answer in two (2) decimal places only without the unit. F1 C a D a A
Find the maximum moment of the given load train at point n on the beam given in the figure? (Single load and distributed load train move on the beam. (a=9 m between n-A, b=3 m between n-B)
answer 2nd question