Workout the Earthwork quantities in embankment and cutting for the chainage length of 600 meters. Formation width is 20m. Side slopes in embankment is 2:1 and in cutting is 1.5:1. There is no transverse slope. Rising gradient of 1:250 upto 250m chaniage. Rising gradient of 1:100 upto 600m chainage. Chainage 0 50 100 150 200 250 300 350 R.L of Ground 152.0 152.35 152.6 152.8 153.0 152.6 152.2 151.5 R.L of Formation 151.6 Chainage 400 450 500 550 600 R.L of Ground 151.2 150.5 150.3 150.5 150.7 R.L of Formation 155.4

Workout the Earthwork quantities in embankment and cutting for the chainage length of 600 meters. Formation width is 20m. Side slopes in embankment is 2:1 and in cutting is 1.5:1. There is no transverse slope. Rising gradient of 1:250 upto 250m chaniage. Rising gradient of 1:100 upto 600m chainage. Chainage 0 50 100 150 200 250 300 350 R.L of Ground 152.0 152.35 152.6 152.8 153.0 152.6 152.2 151.5 R.L of Formation 151.6 Chainage 400 450 500 550 600 R.L of Ground 151.2 150.5 150.3 150.5 150.7 R.L of Formation 155.4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the slope at point C of the beam, E=200GPa, I = 34×106 mm². A 37m All calculation steps are required. B 35 KN/m ↓↓↓↓↓↓ 37m C
St. No. A B C D E F The table below is the page of a level field book. 1) Calculate the difference in level between point A and G. 2) If it is required to build a horizontal embankment along the line AG, so that the elevation of the embankment is higher than the original ground surface with 150cm at point A. Calculate the depth of fill at point D. let RL of A=30m (all the readings in meter) G BS 1.722 1.652 1.622 IS 1.365 1.929 1.723 FS 1.943 1.543 1.343 Dist.(m) 0 50 150 100 200 250 300 0.357m, 1.297 0.365m, 1.998 1.167m, 0.998 0.167m, 1.998 0.567m, 1.157m, 0.978m, 0.167
Please solve using Virtual Work method and Castigliano Theorem. Written solution please. answers should be -5/kNm2 ccw and -2.1825 EI/kNm3 upward
Using the ordinary method of slices, find the factor of safety with respect to sliding for the following case: ?=70° , α=30°, H=12m ,?=18.4 kN/m3 ,c’=20 kN/m2, ?’=20, n’=1
Only in 5 minutes thanks
B 20 ft Y=110 Ib/ft O= 20° c= 400 Ib/ft? 25° 50 A This question has three parts. For the given slope conditions (ABC) and failure surface (AC) shown in the figure: 1) Calculate the factor of safety against sliding. 2) Calculate the factor of safety if c = 0. 3) Calculate the factor of safety if the groundwater level rises to point A.
GEOTECHNICAL ENGINEERINGFor the infinite slope find the FS against slip (AB), with the dataH = 26 ft, Gs = 2.6 e = 0.5 Φ = 22 ° c´ = 600 lb / ft2.There is a water table, coinciding with the surface
St. No. A B C D E F The table below is the page of a level field book. 1) Calculate the difference in level between point A and G. 2) If it is required to build a horizontal embankment along the line AG, so that the elevation of the embankment is higher than the original ground surface with 150cm at point A. Calculate the depth of fill at point D. let RL of A=30m (all the readings in meter) G BS 1.722 1.652 1.622 IS 1.365 1.929 1.723 FS 1.943 1.543 1.343 Dist.(m) 0 50 150 100 200 250 300 0.357m, 1.297 0.365m, 1.998 1.167m, 0.998 0.167m, 1.998 0.567m, 1.157m, 0.978m, 0.167
Slope stability,,
A slope 15 m high and B52 as shown in the figure below, is to be made in a soil whose unit weight angle of friction and cohesion are 16,8 kN/m², 22 and 38.0 kN/m² respectively. Determine the factor of safety of the slope assuming at least three-trial failure line and hence find the factor of safety. Make assumption where necessary. Based on the three FS computed, what factor of safety you recommended. 15 ft A D 520 Ja W Where, h-(D/sinß) sin(B-a) C Y-16.8 kN/m 6-22° c=38.0 kN/m²
The following figure shows an inclined ground section with a depth of H-10 meters in clay sell if the density of the clay is (19) and the value of the sol cohesion resistance in (20), and the length of the circle section 1 315 m. What is required is to find the factor of salety (FS) against slipping on the surface. The circle whose length is 2 151 meter) and around the point (0) using the show method, nuing that the term of wach alice ara as shown in the figure Date: Das a tablete arel make the new cli
15. A planed timber flume, rectangular in cross section is to carry 0.85cms.The depth of is to be 457mm anda width of 1.22m. What should be the slope of the flume? *