4 wo de shunt generators, each with armature resistance0,02 ohm and field resistance of 50 ohms run inarallel and supply a total current of 1000 A to the loadruit. If their emf's are 270 V and 265 V, solve thebar voltage.

Answered: Image /qna-images/answer/6a259022-ee87-4cd8-b3d5-dbbde97d3ebf.jpg

wo de shunt generators, each with armature resistance 0,02 ohm and field resistance of 50 ohms run in Parallel and supply a total current of 1000 A to the load wruit. If their emf's are 270 V and 265 V, solve the

wo de shunt generators, each with armature resistance 0,02 ohm and field resistance of 50 ohms run in Parallel and supply a total current of 1000 A to the load wruit. If their emf's are 270 V and 265 V, solve the

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.1MCQ: The Ohms law for the magnetic circuit states that the net magnetomotive force (mmf) equals the...

See similar textbooks

Related questions

Q: A 0.7-F capacitor is connected in series with a 9-ohm resistor. If the connection is energized from…

Q: In the AM in the figure; a) Modulation index b) Information and Carrier amplitude c) Information and…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Q1 Use Matlab as much as possible to perform the following tasks. You must submit the Matlab…

A: 1) Given polynomials are a) p1 = 2s5-3s4+4s3-s2+3s b) p2 =-s6+5s3-s2-10 We need to determine the…

Q: ΆΛΛΛΛΛ -6 -202 t 0.5 -18 -14 -10 6 10 14 Figure 2: A periodic signal. Consider the periodic signal…

A: Given: A periodic signal, To find: By inspection or otherwise, find Fourier series coefficients,…

Q: The room temperature electron and hole concentration in an N-type Silicon is 1017 and 10¹0 cm-3,…

A: At the room temperature, an N-type silicon has Electron concentration, n = 1017cm-3 Hole…

Q: A Q1 using the curves of Fig. 1: a. Determine the voltage across Si diode at a current of 2 mA. b.…

A: PN Junction diode In a PN junction diode, a semiconductor piece is doped on one side with a donor…

Q: Development standards of radio frequency for human safety

A: Radio frequency- Radio frequency is defined as the frequency at which radio signals operates and…

Q: find the power factor Find the power factor 492 ww 27 V -j252 j5Q2 -j2n Ans pf 0.555 (leading)

Q: Find current I1 using superposition theorem

A: Given below clear explanation

Q: An electromagnet that is modeled as a resistor R=20 ohms and L=0.3 henrys in series, is connected to…

A: Electromagnet modeled as series connection of resistance and inductance whose values are 20 ohms and…

Q: 37) In sequencial order, MOV AL,77H, MOV AH,23H, ADD AL,AH commands are executed. What are numbers…

A: As per our company guidelines we are supposed to answer only first question kindly repost the other…

Q: below Suppose a bandlimited continuous-time signal f(t) with the spectrum shown -2750 f(t) sampling…

A: What is a sampling of signal? Sampling is the conversion of a continuous-time signal into a…

Q: 1. Apply phasor analysis to evaluate the following: a v= [120 sin(10t +20°) + 120 cos(10t - 121°)] V…

A: Given v = [120sin(10t+200) + 120cos(10t-1210) ]V i = [20cos(2t+200) - 15sin(2t-300) ]A Asked to…

Q: a) What will be the distance of two small identical conducting spheres having charges of 8 x 10-⁹…

Q: What are MEMS drug delivery devices? Explain different methods of drug delivery using MEMS.…

A: 1) Micro-electromechanical systems (MEMS) is a processing technology used to create tiny or small…

Q: draw the circuit in block diagram preparation.

A: Given circuit,

Q: It's hard to read， I need handwrite solution

A: Given: To find: For all circuits, i) Transfer function, ii) Magnitude response, iii) Phase…

Q: Specify the system where the machine is use. Specify the ratings and related description of the…

Q: 4 кл 2 кл ли Ш з 12 V Ix 1 ко ч ка 2 ks

Q: The figure shows a cable through which a current I flows, which is composed of a straight segment of…

Q: * The voltage Vout in the circuit shown is

A: Given data, Circuit diagram is given as,

Q: III. Find the current Lby reducing the circuit to the right of terminals a-b to its simplest form…

A: We need to find out the current for given circuit.

Q: 1. A separately excited DC generator has the field connected a. across the armature. b. in series…

A: given are basic questions on DC generators

Q: Question 4 An electrical circuit has a circuit breaker that is designed to trip if the current gets…

A: Given: Voltage, V=120 V Resistance, R=20 Ω Maximum current hold by the circuit breaker before trip,…

Q: Determine the Z-transform of 0.75nu(n-3)

A: We need to find out the z transform for given signal .

Q: Question # 1: Use the Nyquist criterion to find the range of gain K, for stability, instability, and…

A: In this question we need to find the range of K for the given system to be stable, unstable and…

Q: 10.11 The magnetic field component of an EM wave propagating through a nonmagnetic medium (o) is H =…

A: Given: Magnetic component of an EM wave propagating through a nonmagnetic medium:…

Q: determine the current i(t) Χα t = 0 12V Μ 6Ω 3Ω 6Ω www 12H i(t)

A: Given data: The given circuit is shown below,

Q: (b) An aperiodic signal defined below is the input signal to a system is sampled at 4000Hz rate:…

Q: A load supplied by a 3-wire d.c. distribution system takes a current of 600 A on the +ve side and…

A: Given data: The current = 600 A on the +ve side The current = 480 A on the -ve side The resistance,…

Q: 1. A compound-wound generator terminal connection box contains terminal leads a. F1, F2 and A1, A2.…

A: Compound wound generators:- Compound wound generators have both series field winding and shunt…

Q: Find the regulation

Q: Question # 1: Find the static error constants for a stable unity feedback system whose open-loop…

A: OLTF Bode plot is given and we need to find static error constant.

Q: e. With reference to Figure 3 (b), use source transformations to determine the voltage Va R30 E- -9V…

A: We need to find out the output voltage for given circuit .

Q: The input-output relationship for a system is given as: y(n) = h(n) * x(n) where the system impulse…

Q: 8. Design the network of the following circuit to maintain V₁ at 12V for a load variation (IL) from…

A: In this question We need to determine the rating of the zener diode. We know Power P= VZ IZ

Q: 7. Calculate the output voltage expression for the circuit

Q: Consider the discrete-time system shown in Figure Q1 (b). Determine if the system is (i) time…

A: We need to check whether the given system is time invariant and linear.

Q: A loss less transmission line having Surge Impedance Loading (SIL) of 2280 MW is provided with a…

A: Given: A loss less transmission line with, Surge impedance loading, SIL1=2280 MW At a uniformly…

Q: Two long parallel conductors carry 200 A. If the conductors are separated by 40 mm, the force per…

A: Given, current in both conductors, I1=I2=200 A The separation between the conductors,d=40×10-3 m

Q: 1. A generator series field-diverter rheostat is always connected a. in parallel with the series…

A: basic questions on DC machines

Q: Consider the signal ≤ n ≤2 y (n) = {0, elsewhere a) Compute the DTFT of the signal i.e. Y(w). Find…

A: Given: y(n)=1 ;0≤n≤20 ;otherwise To find: a) DTFT of the signal. Sketch the magnitude and phase…

Q: 5. Use superposition to calculate the current i, in Circuit 5.

A: The superposition theorem state that the sum of response of individual sources acting alone is equal…

Q: Semiconductor fabrication Consider a wafer of Si crystal which has a uniform boron (B) doping of 1 x…

A: Given: In this question, the given details are, A wafer of Si crystal which has a uniform boron (B)…

Q: QUESTION Research and design a Distributed control system for any random industry and state how…

A: Distributed control system (DCS) This type is more reliable than the PLC (Programmable Logic…

Q: 3. Given the sinusoid current i(t) = 74 cos(24t +7°) A, find the period and frequency.

A: In this question we need to find the time period and frequency of the given sinusoidal current.

Q: In the circuit shown below, the initial capacitor voltage is 4V. Switch S₁ is closed at t = 0. The…

A: Given- Initial capacitor voltage = 4 V, At t=0, switch S1 is closed, Circuit as shown, To Find- The…

Q: Write a function to create a single instance of a pulsed square wave. A good example of a pulse…

A: We need to draw the pulsed square wave having value of '1' for the starting point on time axis is…

Q: Consider the discrete-time signal x[n] shown below. Let its DTFT be denoted by X (ein). 4-3 -2 (a)…

A: As per the guidelines of bartleby i need to answer first three subparts only so kindly repost other…

Q: Q3 - Use the final value theorem to determine (IF POSSIBLE) the steady state value of the following…

A: As per our company guidelines we are supposed to answer only first three subparts kindly repost the…

Concept explainers

DC Generator

An electromechanical machine which converts input mechanical energy to respective output electric energy is called a generator.

Question

wo de shunt generators, each with armature resistance
0,02 ohm and field resistance of 50 ohms run in
arallel and supply a total current of 1000 A to the load
ruit. If their emf's are 270 V and 265 V, solve the
bar voltage.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 50kW, 500V short shunt generator has an armature resistance, series field resistance and shunt field resistances are 0.05 ohms, 0.06 ohms and 253 ohms respectively. What is the power generated?
Fhe number of parallel paths and the number of series conductrs required for a given kW reting are determined by. System voltage Armature resistance Type of winding Field current
A 12 V generator has an internal resistance of 0.05 ohm. Two loads are connected in parallel to its terminals, one drawing a 12 A current and the other dissipating energy at the rate of 200 W. What is the terminal voltage of the generator with this load? Ans. 0.82 volts
A 220V series generator has an armature resistance of 0.04Ω. If the generated emf is 230V and the drop across the series field winding is 9V, what is the ohmic resistance (in ohms) of the series field winding?
Two D.C. shunt generators, each with armature resistance of 0.02 ohm and field resistance of 50 ohm run in parallel and supply a total current of 1000 amperes to the load circuit. If their e.m.fs. are 270 V and 265 V, their bus bar voltage will be 270 V O 267.5 V O 265 V O 257.4 V O
A shunt generator delivers 68 A and 230 V and the shunt field and armature resistance are 115 ohms and 0.05 ohm respectively. What is the generated emf
Quèstion 7 A shunt generator running at 1000 r.p.m. has generated e.m.f. as 300 V. If the speed increases to 1200 r.p.m., the generated e.m.f. will be nearly 300 480 420 360 A Movinn to another ouestion will caro thic roenonco P Type here to search O O O O
A three-winding transformer is connected to an AC voltage source as shown in the figure. The number of turns is as follows: N₁ = 100, N₂ = 50, N3 = 50. If the magnetizing current is neglected, and the currents in two windings on secondary side are 2230° and 22150°, then what is the value of the primary current in Ampere? I 0000000000- N₁ № ₂ Z 00000 00000 Z N3 H I₁₂ I₁₂₁ ¹3
Q2) Three shunt generators operate in parallel and supply a load current of 12000 A, connected across the bus-bars. Details of the generators are given below, Eg4 = 450 V EgB = 460 V Egc = 410 V Generator A Generator B Generator C Raa = 0.02 N Ra = 0.025 A Rac = 0.01 a) Calculate the load voltage (bus bar voltage). b) Find the current supplied by each generator. c) Determine the output power (in KW) for each machine Neglect field current.
A short shunt compound generator supplies a load of 20 kW at 500 V. The armature, series and shunt field resistance are 0.10 ohm, 0.05 ohm, and 100 ohms respectively. Find the power developed in the armature. Choices: 24600 W 20500 W 22800 W 25400 W
In the circuit in Figure 2, the capacitor connected to the a-b terminals of the transformer anda circuit consisting of resistance is defined as a load circuit. a)Find the average power spent by the load circuit? b) How much of the average power calculated in a) by the resistance in the load circuit and how muchspent by the capacitor? Comment on the results obtained?
An 8.2kW seriesd generator has an armature resistance is 0.25 ohms with a generated voltage equal to 4212.43 V. Determine the series field resistance should be installed in this machine in order to supply a load at 400V.