Q2. The reduce level is mentioned in table below to build a wide road withwidth (8 m) and grade line for the road is (18m) with Sloped down 0.5% andlateral inclination is 1:1. The distance between the station is (100 m). Calculatethe total fill and cut volume.15.4 m17.5 m16.5 m17.2 mGround Line(G.L)Station0+001+002+003+00

Answered: Image /qna-images/answer/afa4a383-e3b9-4f28-838a-421cbd085ed2.jpg

Answered: width (8 m) and grade line for the road…

width (8 m) and grade line for the road is lateral inclination is 1:1. The distance between the station is (100 m). Calculat the total fill and cut volume.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A field pumping test was conducted from an aquifer of sandy soil of 4 m thickness confined between…

Q: Fill the blanks for the following points: 1- We find the undrained cohesion of the soil using 2- The…

A: 1. We find the undrained cohesion of the soil using Triaxial test. 2. The case of a moving load…

Q: 5. Oil (S=0.92) is transported through the system as shown below. If the pressure head difference…

A: Given :

Q: Using the ACI code equation, estimate what would be the modulus of elasticity of this concrete at…

A: Modulus of elasticity of concrete= 4700f'c= 4700*4.909=23073.123 MPa As per ACI Code

Q: Determine the discharge, in L/s, over the weir having a head of 0.30 m if a a contracted rectangular…

Q: A 400 cubic cm sample from the top 25 cm of a soil weighed 686 g when collected and 576 g when oven…

A: Asked: To determine the bulk density, percent water and the field capacity deficit of the soil zone.…

Q: 1. For the cantilever beam and loading shown, determine the slope and deflection at (a) end A, (b)…

Q: Q2: Determine the state Of stresses at point A on the cross section of the beam shown in Fig. at…

Q: Q.5. For the beam shown in Figure (5), assume that El = 5x10 kN.m². Determine: a) The concentrated…

A: Find 1. Concentrated moment at A to make zero slope at A. 2. Support reaction at B 3. Deflection…

Q: Situation # 3: Assume that the frame in figure C is pin-connected at points A, B, and C, and that…

Q: . Which of the following most nearly gives the rise above the ground surface when a piezometer is…

Q: What is the principle behind ecological engineering

A: These are the some basic principle oehind ecological engineering are such as follows :- Principle 1:…

Q: The pump shown in the figure draws water from Reservoir A and discharges the fluid into a nozzle at…

Q: At the given instant member AB has the angular motions shown. Determine the velocity and…

Q: 1. Draw the shear force and bending moment diagrams for the frame shown in the figure using moment…

A: Since there is no loading in span AB & CD hence fixed end moments will be zero for these members…

Q: Determine the support reactions with explanation

A: Given A beam Required Support reactions

Q: Water flows at the rate of 12 m³/s, at a depth of 1.5 m, in a 10 m wide irrigation canal. Assume…

Q: A beam loaded with uniform load 10.7 KN/m is shown below. It has a total length of 12 m. Find the…

Q: SYSTEMATIC ERRORS IN TAPING + TAPE IS NOT OF STANDARD LENGTH A building 38 × 45 m is to be laid out…

Q: sample at 28 days has a diameter of 5.9in and maximum loading of 88,877.96lb, what is the…

A: Given Diameter =5.9 inch Maximum load =88877.96lb Cross section area ?

Q: A force F of magnitude 60 N is applied to the gear. Determine the moment of F about point O. F=60 N…

Q: PROBLEM No. 1: (a) Derive the shear force and bending moment equations for the cantilever beam. (b)…

Q: The answer should be in Nm

A: State the largest bending moment to be applied safely in N-m rounded to three decimal places

Q: Calculate the deflection at B using Area Moment Method. Answer in terms of El. P1 = 101 kN w = 37…

Q: A rectangular channel 9 m wide carries 7.65 m3/s when flowing 0.90 m deep. What is the critical…

Q: 1) The PERT method to solve? a) Game theory b) transportation model 2) To find the saddle point in…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: The Portland Cement Association recommends a minimum cement content of for concrete placed under…

A: Minimum cement content is 564 lb/yd^3

Q: A normal-weight concrete has an average compressive strength of 20 MPa. What is the estimated…

A: Flexural strength of concrete is between 10-20% of compressive strength ie 2-4 N/mm2 or MPa

Q: A water tower supplies water through the plumbing in a house. A 2.40-cm-diameter faucet in the house…

Q: Determine the force in each member of the framework shown in the figure that supports a vertical…

Q: If the allowable stresses are: 6t=165M, 5c = 100Mpa, T=701 Pa determinet max. value of c. KN Ans.…

A: Given A beam with T -section Required Maximum value of distributed loading

Q: Based on the Sieve Analysis results for filter media given below: Size of Opening (mm) Cumulative…

A: Given the results of Sieve analysis test results for filter media. The effective size = d10 : It is…

Q: Determine the velocity of each block 2 s after the blocks are released from rest. Neglect the mass…

A: Determine the velocity of each block 2 s after the blocks are released from rest. Neglect the mass…

Q: Design Slab DEGH of the floor system shown below. Dead load pressure including the slab's weight is…

A: Solution: Given: DL = 5.3 KPa LL = 2.4 KPa fc = 21 MPa fy = 345 MPa beam = 350 x 500 mm use 12 mm…

Q: A third-point loading flexural (bending) test was performed on a concrete beam with a cross section…

Q: A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress…

Q: In shown figure the aluminum is subjected to a thermal stress where T₁ is 21.957 deg. C and T2 is…

Q: Determine the 5-day BOD (in mg/L) for a 15 ml sample that is diluted with dilution water to a total…

Q: In a city, the population to be served: 78,320 and per capita waste generation is 0.85 kg/capita/day…

Q: A printing machine is to be installed at a cost of 38000 in a press. Assuming the life of the…

A: given cost of machine S=38,000life n=25 yearscompound interest i=5%salvage value=3500

Q: The two structural members, one of which is in tension and the other in compression, exert the…

Q: (3) Use Virtual Work to determine slopes at A, B and C, and the displacement at C. Check all results…

A: As per policy, only one question can be answered. For solution using the moment area method kindly…

Q: H.W 4 A simple beam on a 10 ft span supports a uniform load of intensity 800 lb/ft (see figure). The…

Q: A simply supported wood beam is reinforced with a steel plate of width b as shown in the figure. The…

Q: a section 2.07 m from A if P = 5470 N. W=2372 N/m, a = 1.2 m, b = final answer to two decimal…

Q: Q3. A sphere is tested for drag resistance in a the wind tunnel. A pressure tapping at the…

A: Given :

Q: +9/ZXT +]}6 (

Q: In the portal frame shown, sway is prevented by a reaction at B. Draw the bending moment and shear…

A: Given A frame Required Shear and bending moment diagram And also find the sway reaction at B.

Q: conducted an aquifer of sandy soil 4 m thickness confined between two impervious strata. When…

Q: 2.17 The specimen shown has been cut from a -in.-thick sheet of vinyl (E = 0.45 × 10 psi) and is…

Concept explainers

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.

Question

Q2. The reduce level is mentioned in table below to build a wide road with
width (8 m) and grade line for the road is (18m) with Sloped down 0.5% and
lateral inclination is 1:1. The distance between the station is (100 m). Calculate
the total fill and cut volume.
15.4 m
17.5 m
16.5 m
17.2 m
Ground Line
(G.L)
Station
0+00
1+00
2+00
3+00

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the given road cross section notes, the width of the road is 11.00 meters with SSof 1:1. Find the earthwork volume using the following methods: • Average End Area• Prismoidal Formula• Prismoidal Correction• Road Sections STA 10 + 000 3.00 1.50 1.00 -8.50 0.00 6.50 STA 10 + 020 2.20 1.20 2.60 -7.70 0.00 8.1
Calculate the quantity of earth work for the road with the following: stations 0 Depth of cut (m) 1 Height of filling(m) 100 200 300 400 3 0.5 The width of road-10 m, side slope 1:1 to cut and fill. 1 2
QUESTION 1 In a certain portion of road to be constructed, the following data were taken. Station 1+020 8m 8.5m -1.555 ? 1.25 m² m² m³ -1.21 Station 1+090 0 +2.55 Base width for cut Base width for fill 1.25:1 Side slope for cut 1:1 Side slope for fill ____?__ -0.9 0.95 a) Compute area of first station b) Compute area of second station c) Determine difference in volume of cut and fill using End Area Method
A series levelling had been down along the centre line of the proposed road the distance between each two points (100m). If the elevation of the points A, E and H after completing the project should be 31m, 30m, and 31.5m respectively and these three points connected with straight lines having uniform gradient. Calculate the depth of cut and fill for the points C and G. St. No. BS IS FS Remark A 1.25 2.18 1.78 1.93 D 1.91 1.27 E 1.86 В.М-30.09 F 1.61 G 1.43 H 2.7
The following are section notes of a five-level section Station 1+ 125 ? 12.0 10.0 -5.3,- - 4.0'-8.80 -6.20’ – 6.0 Station 1 + 175 22 13 9 20 +5.2 +7 +4.2 +4.3 +3.1 • Assume the following: Base of roadway: 20 m - Sideslopes: 1.5:1 Required: - Determine the area of the cross-section - The volume of excavation and fill using end-area method
Dermine the volume of borrow. The grading works of a portion of the proposed expressway shows the following notes. Limits of free haul distance is from STA 1+272 to STA 1+322 Limits of economical haul is from STA 1+052 to STA 1+502 STATION 1+000 1+052 1+272 1+300 1+322 1+502 1+600 CUT (m²) 0 3.845 40.18 60 FILL (m²) 40 33 3.021 Balancing point
A series levelling had been down along the centre line of the proposed road the distance between each two points (100m). If the elevation of the points A, E and H after completing the project should be 31m, 30m, and 31.5m respectively and these three points connected with straight lines having uniform gradient. Calculate the depth of cut and fill for the points C and G. * St. No. BS IS FS Remark A 1.25 2.18 C 1.78 1.93 D 1.91 1.27 E 1.86 В.М-30.09 1.61 1.43 2.7
A series levelling had been down along the centre line of the proposed road the distance between each two points (100m). If the elevation of the points A, E and H after completing the project should be 31m, 30m, and 31.5m respectively and these three points connected with straight lines having uniform gradient. Calculate the depth of cut and fill for the points C and G.
Given the following set of slope staking notes: Sta oooo 23+00 22+00 21+00 20+50 34.7 O 46.3 38.6 O 48.2 L 23.1 FX₁ 21.6 0 25.0 F 2.5 20.0 F 5.1 25.2 C 0 C 4.9 0 0 R C 5.8 X₂ What is the fill volume between stations 21+00 and 22+00, in cubic yards? [choose the most correct answer] C 9.0 43.0 C 4.3 33.6 C 2.1 29.2 Bases Base for cut = 50 ft Base for fill = 30 ft s = 2:1
Q6/ Below the elevation of points on the center of road project. If the D.L is start at elevation (25m) with ascending slope (0.5%). Find the heights of Fill and depths of cut for each points. с E F H I 100 150 200 250 300 350 400 25.7 25,2 24.8 26.6 26.8 27.2 27 60 28.0 Points A Dist. 0.0 C 26 B 50
From the following cross-section notes, compute the volume of cut and fill using end-area method, the roadbed being 6m wide in cut and 4.8m in fill. The side slope for both cut and fill is 1:1. Station 3+000 +0.39 5.04 0.60 5.46 -2.64 0 +2.46 Station 2+980 5.82 1.02 +0.60 4.80 -3.42 0 +1.80
Calculate the amount of earthwork for the cut and fill section between (42+00) and (42+40) stations, knowing that the width of road section at cut area is 7.2 m and at fill, area is 6.0 m Stations Cross-section f 0.4 f 1.5 f 2.1 42+00 3.6 6.15 c 1.85 f1.4 42+30 3.0 5.1 f 1.5 c 0.7 42+40 5.85 4.05 이ㅇ 이이