The two structural members, one of which is in tension and the other in compression, exert the indicated forces on joint O. Determine the magnitude of the resultant R of the two forces and the angle which R makes with the positive x-axis. The angle 0 is measured counterclockwise from the positive x-axis. 4.1 kN 2.0 KN- Answers: R= i 0= i 37° 519 KN

The two structural members, one of which is in tension and the other in compression, exert the indicated forces on joint O. Determine the magnitude of the resultant R of the two forces and the angle which R makes with the positive x-axis. The angle 0 is measured counterclockwise from the positive x-axis. 4.1 kN 2.0 KN- Answers: R= i 0= i 37° 519 KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

50 kN 100 kN 50 kN E D F 1 m B 2 at 2m = 4m EA = constant E = 120 GPa In addition to the loads of the truss shown in the figure, the truss has concentrated load of 75 kN (to the right), at joint D. Determine the total deflection at joint B in mm. Assume that the cross sectional area is 2000 mm2.
1. A beam ABCD is hinge supported at A, B, and C. AB = BC = CD = 7m. The support B and C sink 6mm and 8 mm respectively. The point D carries a point load of 1 kN. Take E = 2 x 10^5 MPa; I = 4 x 10^7 mm^4 and draw the bending moment diagram by slope deflection method. %3D %3D
Using mcd pls
A cantilever beam 4 m long carries a uniform load of 3.5 kN/m over'a portion 1.5 m from the free end on the right. Use E = 200 GPa and I = 30x10^6 mm^4. %3D Determine the rotation at the free end. O 0.367° O 0.0054° O 0.269° O 0.0047° Determine the deflection at the free end. O 9.22 mm 18.56 mm O 12.45 mm 13.54 mm
A) determine the value of constant of integration C1 and C2 in lb-ft^2. B) determine the slope at point B. C) determine the defelction at point B in inches.
A concentrated load P = 5 kN, acting downwards, is located midway between the simple supports of the beam shown. Determine the deflection, in mm, at the free-end C. Use a = 5 m., E = 207 GPa, and I = 252 x10^6 mm^4.
Determine the force in each member of the structure and establish whether the members are in tension or compression. Establish P1= 45 KN, P2= 30 KNSolve the problem considering the following: The force P1 will be the maximum point of a triangularly distributed load with a horizontal distribution of X meters.You must leave the solution in terms of X and show the particular solution when X is equal to 0m and 2m.
(3) For the truss shown, compute the horizontal and vertical components of the displacement of joint B. The area of all bars = 2500 mm2, and E=210 GPa. 1200 kN D IM BI 4 m 3 m 3 m E 300 KN
7.
Please solve the problem using Castigliano's Theorem.
The pole is supported by a pin at B and A-36 steel guy wire AC. If the wire has a diameter of 0.2. Modulus of Elasticity of Steel = 200GPA or 29x103 ksi Poisson's ratio of steel=0.321 3 ft 30 D 2.5 kip 4 ft B 1. At what angle is the principal stresses on pole BC? Use Mohr's Circle. 2. What is the principal stress in pol BC? Use Mohr's Circle 3. Draw the stresses on a unit element acting on 35-degree clockwise direction of pole BC. Use Mohr's Circle. 4. What are the principal stresses in point D? Use Mohr's Circle. (answer in ksi) 5. At what angle is the principal stresses acting on point D? Use Mohr 's Circle. 6. Draw the stresses on a unit element acting on 35degree-clockwise direction of point D. Use Mohr's Circle. (answer in ksi)
solve fast