Why should a technician not file the rough surface on the contractors contacts

Q: ]means the repair work done to keep the system in good working condition.

A: It is required to fill the blank

Q: Compare the two forms of maintenance.

A: Two major forms of maintenance activity in a mechanical process are: 1. Preventive Maintenance 2.…

Q: Cleaning a machine with compressed air is a general safety precautions considered while working in a…

A:

Q: ..... ..... will extend the life of the equipment

A: ................. Will extend the life of the equipment.

Q: Which one of the following reboiler requires more complex pipe work? Horizontal thermosyphon…

A: Horizontal thermosyphon reboiler are depends on natural circulation where in shell sides,…

Q: used between slides and slideways are designed to keep out cutting fluids from falling into the…

A:

Q: a large piece of 1 vo sections: hem cutting m machining jet machining

A: Required  Which is the correct method for cutting of steel plate

Q: Water is flowing thru the pipe set-up. What can be the v thru pipe 3 ?

A:

Q: يمكننا إدخال رقم صفحة من خالل 0 0 ( Footer Both Header and Footer > Header None of the above > O

A: In the Microsoft we can enter page number in the footer. Header

Q: Kind of "manual control and automatic" scrap machine

A: Shaping and Planning are the operation of removing a layer of work material from the flat surface…

Q: When changing a cartridge oil filter, the only parts that get replaced are the paper filter…

A: Answer : O-rings

Q: How is it possible to decrease contact resistance? By using different fluids for better matching O…

A: Contact resistance is the resistance that hinders the flow of heat by conduction.

Q: Select the right reading of the ?Micrometer Screw Gauge

A: we need to find reading in the micrometer.

Q: Identify a true statement while maintaining wiper pads used on lathe machine O Compressed air can be…

A: To find: True statement while maintaining wiper pads used on lathe machine from given options

Q: Identify the point to be considered while maintenance of wiper pads on lathe machine Regularly…

A: To find: what point to be considered while maintenance of wiper pads on lathe machine.

Q: Describe the importance of planning before moving an item.

A: Let's evaluate importance of planning before moving an item.

Q: iii) Mention any two disadvantages of bad maintenance

A: It will decrease  lifespan of the asset .

Q: Write a short note any five sections of separator? in oil And gas

A:

Q: List six steps involved in performing a visual inspection.

A: Visual inspection is the method of checking for the defects using naked eye. Visual inspection is…

Q: The technician............... machine, but ............... no time. He wasn't very busy. to repair…

A: GIven

Q: Match the following questions with answers To stop dirt being drawn inside with the rod. Irregular…

A:

Q: Describe the range of maintenanceactivities.

A: It is a task that is to be performed to preserve an asset. The task help to provide continuity and…

Q: Please choose the correct answer about scrubber systems on ships.

A: Scrubber systems can be implemented existing ship as per new ship regulation, so option A is wrong .…

Q: Explain how its work and the proper procedure

A: A shaper is a versatile machine tool that is primarily used to create a flat surface using a…

Q: A type of maintenance is called a stitch in time procedure. a. Predictive O b. Preventive O c.…

A: Predictive maintenance - In this type, maintenance is done on the basis of the prediction of any…

Q: Describe any three uses of the following gauge.

A:

Q: While Drilling it is permissible to leave the check key in check while drilling a hole.

A: While Drilling it is permissible to leave the check key in check while drilling a hole. Answer:…

Q: From the following identify the false statement . In general safety precaution, the machine…

A: All the first 3 statements are correct but In housekeeping safety precaution, the machine should be…

Q: List down the safety precaution need to carry during the operation of drilling machine?

A: During the operation of drilling we need to take two types of safety precautions: 1. Fire Hazards…

Q: Compressed air can be used to clean the machine, is a general safety precaution while working in a…

A: Compressed air can be used to clean the machine, is a general safety precaution while working in a…

Q: Well Completion : Tubing leaks is one of well completion problems. the causes and method(s) to…

A: Causes of tube leaks: 1.High water pressure leads to damaging wear and tear on your pipes. Water…

Q: Which fixture would be the most suitable for welding up and drilling the holes for fixture for the…

A: Modular fixture is most suitable for welding up and drilling the holes for fixture for the complete…

Q: a steel wall a temperati

A:

Q: 0..

A: given; Type of automatic control on scrap machine on given figure.

Q: 30. The methods of overhaul differ from maintenance procedure. a. True b. False

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: basic technique of operating a scrap machine

A: Scrap can be anything that results in wasted material and a need to perform rework of some kind. In…

Q: mechanical properrty of the metal. a. Specific gravity

A: Stiffness is a property of material which is that offers resistance to deformation when external…

Q: What i deep g a cons 80 rpm

A: Given data,Fr=2820NN=80deep groove ball bearing=6308SKF

Q: How can air pressure be used to check an electricalswitch?

A: According to the study air pressure is used to check electrical switch. When pressurized air is…

Q: t and clean handwritten solution

A: It is an alloy of iron that has 2 to 4% of carbon present in it. It can be obtained by reducing the…

Q: Discuss the line maintenance, repairs and alterations.

A: Aircraft maintenance is a highly regulated sector that requires licenced Maintenance, Repair, and…

Q: Which has the higher viscosity, grease or oil

A: Viscosity is the property of a fluid which resists its flow. It can be considered as equivalent to…

Q: Why should the machine be kept clean and properly oiled?

A: To explain: The reason behind the machine to be kept clean and properly oiled. Explanation: The…

Q: Wipers pads on lathe machines are used between slides and slideways cannot be cleaned using…

A: The wipers should be removed, cleaned, and re-saturated with oil regularly. Never use compressed air…

Q: Name the two types of vacuum procedures used by technicians.

A: deep vacuum and triple evacuations Deep Vacuum: it lowers the boiling points of the liquids. It…

Q: describe the information that should be include on a repair order.

A: Repair order A repair order is a record of the parts and labor operations that were actually used…

Q: Identify the specific steps when Conduct a lock-out and tag-out activity in the oil rig to repair…

A: Steps in directing lock out tag out action in oil rig for the penetrating machine change  For the…

Metrology of surface finish

In general terms, the application of scientific principles in the study of measurements is known as metrology. When speaking about measurement, it could be of time, length, microstructures, grain structures, internal crystal discontinuities, surface roughness, measurements of angles, height, width, and so on. While coming to the domain of mechanical engineering, metrology is considered the science of measurements of surface finish, length, surface texture, and angles.