Kind of "manual control and automatic" scrap machine

Q: 71) Which is not a surface texture parameter? A) roughness B) cutting length C) array D) wavy E)…

A: As per our guideline we can answer only one question at a time ,you are requested to post other…

Q: Do you need to carry any other equipment or maintenance item to the site to keep the SCREWDRIVER…

A: Solution:   Screwdriver is a tool used to provide torque at the face of the bolt or stud.

Q: Which of the following tools is essential in sheet metal job but not in a fitting job? A. Steel…

A: Steel ruler- it is a measuring tool to measure the linear dimensions. It is used in fitting job.…

Q: History of engine lathe       Types of engine lathe       Parts of an engine lathe and their…

A: During the Industrial Revolution, the lathe was extremely essential. Around 1751, Jacques de…

Q: Identify a secondary machining process from the following. [A] Brazing [B] Broaching [C] Buffing [D]…

A: A process on the metal which is performed after completion of the initial manufacturing process is…

Q: How has the material removal process evolved over time؟

A: How has the material removal process evolved

Q: Choose TWO (2) types of cutting processes for cutting thin metal (sheet metal)

A:

Q: 4. What personal protective equipment should you wear when you are using the tool (if any)? For…

A: 4. PPE:- Personal Protective equipment (PPE) is the equipment worn to reduce exposures to hazards…

Q: Differentiate between Assembly Drawing and Assembly Chart?

A: Assembly Drawing:               Assembly drawing is a sketch of a machine. A simple diagram of the…

Q: Gear finishing operation is called:    A) Burnishing B) Hobbing C) Shaping D) Milling

A: Given Data⇒Gear finishingProblem definition⇒Problem says choose the correct option

Q: 5. Does the tool have any fragile or delicate parts that need to be protected? If so, how do you…

A: Solution: Note: Dear Student! As per our guidelines, we are only allowed to answer a single…

Q: During the operation of the product, does the part move relative to all other parts already…

A: "Design for Manufacture and Assembly(DFMA)"  optimises the manufacturing and assembly operations of…

Q: In which of the following layout type, materials are fed into the first machine and finished…

A: givenMaterials are fed into the first machine and finished products come out of the last machine.

Q: During the quarrying process, the primary conveyor sends material to which compartment?

A: Quarrying Process: Quarrying is the process of removing rock, sand, gravel or other minerals from…

Q: 20)When a thick material is to be cut by WJC, one should prefer

A: All of these is correct according to given question for thick material so  Option d is absolutely…

Q: __ are cutting processes used to form the edge or surface of wood.

A: ___ are cutting processes used to form the edge or surface of wood.

Q: that is the differ ence between. exteusive and intensive proper fies.

A:

Q: Which type of machine tool is the most suited to produce parts with such form? O Drilling machine…

A: Machine tool is a power driven machine, which is capable of performing several machining operations…

Q: Need to sketch initial design of automated hammering machine. Sketch should be in simple and proper…

A: Automated hammering machine can be used for forging operation and can be power driven combined with…

Q: 6. Does the tool have any parts that are designed to wear out and be replaced on a regular basis?…

A: Solution: Note: Dear Student! As per our guidelines, we are only allowed to answer a single…

Q: Q1- Compare between the ferrous and non-ferrous metals in terms of the strength, hardness, weight,…

A: Ferrous metals contain iron, and non-ferrous metals don't. That means each type of ferrous and…

Q: Does the PLIERS have any fragile or delicate parts that need to be protected? If so, how do you…

A: Solution:   Pliers or Cutting Pliers are the mechanical tool used to cut wires, cables at the job…

Q: Which of the following process for sheet metal cutting, the cut piece is the desired part? Shearing…

A:

Q: In which of the following layout type raw materials are fed into the first machine and finished…

A: The layout is defined as the systematic arrangement of the machines, equipment, and other entities…

Q: the shaper machine work processes

A:

Q: What are the main things that can go wrong with the tool (wrench)? For each problem you state,…

A: Whatever impact wrench you use, make sure to use it correctly to avoid damaging the equipment you're…

Q: High tensile strength materials are cut by a single point cutting too with the negative rake angle

A: Yes ,High tensile strength materials are cut by a single point cutting too with the negative rake…

Q: Hollow shape parts are made __________ process. a. Cold rolling b. Wire drawing c. Deep drawing d.…

A: Rolling process are use to produce the symmetrical objects. Wire drawing process is used to produce…

Q: What is the sliding block?

A: To Define: Sliding block

Q: Describe three basic categories of material removal process.

A: given: Describe three basic categories of material removal process.

Q: ENGINE LATHE PROCESSES       History of engine lathe       Types of engine lathe       Parts of an…

A:

Q: What’s the difference between radial arm and upright drill press?     a)Different cutting tool…

A: Given data : radial arm upright drill press

Q: Main characteristic when cutting Steel ISO P is: Machining at higher speeds creates abrasive wear…

A: Answer is given below:

Q: _________ is a massive and rigid single piece casting made to support other active parts of a lathe…

A: The Answer is option [D] Bed.

Q: a) Describe THREE (3) types of Materials Selection Method with appropriate example for each method.

A: Three Method of material selection 1.Initial Screening. 2.Developing and Comparing alternatives…

Q: Tool design What are some of the typical considerations for each one of the following metal cutting…

A: Metal cutting Process It is the process to remove unwanted material in the form of chips from the…

Q: 1+1?

A: Basics of CALCULATION.

Q: Why should you avoid recutting or grinding parts whenever possible?

A: When fabricating a weldment that is made up of all parts welded together there is the main problem…

Q: What are two advantages of using a shrink-fit toolholder ?

A:

Q: Identify other product that involves Shaper Machine Procedure.

A: A shaper machine is a reciprocating type of machine tool used to produce flat horizontal and…

Q: ʙʀɪᴇꜰʟʏ ᴅɪꜱᴄᴜꜱꜱ ᴛʜᴇ ᴀᴄᴄᴇʟᴇʀᴀᴛɪᴏɴ ᴘᴏʟʏɢᴏɴ  Thank you!!

A:

Q: How long does the metal removal process take?

A: Given data :-  Metal removal process :-  Metal removal processes use a metal cutting tool that moves…

Q: 5) Which of the following process parameters is the most significant for linear material removal…

A: Solution:

Q: oaching is an example of __________________________________. secondary machining process joining…

A: Broaching is an example of material removal secondary machining process.

Q: what types of work that will be carried out on the scrap machine

A: On a scrap machine shredding is done, it breaks the material into small pieces. The material is…

Q: What are the different categories of work as distinguished by equipment requirements?

A: The work that is performed as per the equipment requirements is known as Maintenance of the…

Q: A variety of __________ saws blades are available for rough cuts in wood, smoother cuts in wood,…

A: A Reciprocating Saw is a handheld saw commonly used for demolition and remodeling. You can use it to…