Why are flashing light warning units used
Q: What does it mean when a switch is "congested
A: Introduction - Congestion in a network is defined as a decrease in quality of service (QOS) that…
Q: Explain this diagram for dummy
A: The given circuit is as shown below,
Q: The following is a layout of a lighting circuit for the bathroom and hallway. Using the cable layout…
A: Given the layout of a lighting circuit for the bathroom and hallway:
Q: 12. What is the primary entity that needs to be consulted with in regards to the location of the…
A: According to the electric code, The meter and the service box should be placed outdoor which can be…
Q: what wire size is needed on a one 20 amp, 120-volt laundry branch circuit? what wire size is needed…
A: 12 gauge what wire size is needed on a one 20 amp, 120-volt laundry branch circuit.
Q: For installing directly in a concrete slab, (armored cable), (non metallic-sheated cable), (rigid…
A: For installing directly in a concrete slab Rigid metal conduit (RMC) can be used. A rigid metal…
Q: Explain the diagram
A: The above diagram shows the connection to drive a unipolar stepper motor using ULN2803A Array with a…
Q: In a large new car dealership, the individual who oversees the operation of the service department,…
A: A large car dealership service director looks after the operation of the service department, parts…
Q: Q.1: Non-metallic conduit must not be installed where extremes of ambient temperature, why?
A: Since you have asked multiple questions, we will solve the first question for you. If you want any…
Q: The NEC requires that each service-disconnecting means be suitable for A. the prevailing…
A: The service disconnecting mechanisms used to isolate a building's premises wire from the utility…
Q: What unique type of electrical protection is required for all 120-volt, single-phase, 15- and…
A:
Q: What is the branch circuit protective device?
A: Branch circuit protective device is used to protect the motor winding and insulation if due to some…
Q: Which of the following must be notified prior to equipment shutdown for repair? a. Director of…
A: In this question we will write Which must be notified prior to equipment shutdown for repair..
Q: Diagram 43 gives the voltage pulses created by the apparatus of diagram 42. The period of the…
A: The period of the induction coil interrupter is the time taken by a complete cycle of the wave to…
Q: Explain about time graded and current graded system?
A:
Q: The block diagram belong to .....?
A:
Q: Identify and explain the safety procedures and precautions that should be followed for fire…
A: Safety precautions for fire prevention - Always Get Ready with the emergency plan Training of…
Q: What is the scope and Limitation of fence lighting with Alarm circuit?
A: It is a type of electro-electric device which is use to trigger the relay for the operating the AC…
Q: For the following circuit, write a code on TinkerCAD to turn on the LED light when the push-button…
A: Given the circuit, as shown below: For the following circuit, we need to write a code on TinkerCAD…
Q: IS it a requirement to have a light ixture outside the garage door for a vehicle? O No Yes For two…
A:
Q: Classify whether Train door system (driverless train) is an open-loop or closed-loop control system.…
A: Train door system in a driverless train is closed loop control system.
Q: 16. What devices are used to protect a circuit from overloads?
A: 16) to protect a circuit from overloads
Q: 4. Why are the outer metal parts of electrical appliances grounded?
A:
Q: Where is the Service Entrance Panel located?
A: A residential lighting layout plan is shown in the question. We need to find out in which area is…
Q: Do not worry about "box fill" when working with dimmer and speed control devices. They are about the…
A: Compare between Size of dimmer and speed control devices. They are about the same size as regular…
Q: What is bus bar in electrical?
A: The bus bar in the electrical system is known as the conductor or the bunch of conductor which is…
Q: What code sets stabdard for the electrical installation work?
A: In the following section, the code which sets standards for electrical installation work has been…
Q: Which of the following is not a control system? Select the correct answer below: A. Home PC B.…
A: Control system- A control system is basically the interconnection or arrangement of various devices…
Q: 15. Why is it necessary to have a good grounding system for the building?
A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…
Q: The ends of conduit must be reamed and entries to boxes and accessories must be bushed in…
A: A conduit is a tube for protecting electric wiring. it generally made of various material like PVC ,…
Q: procedures
A: Explanation: The safety procedures and precautions to be taken when working with tools and…
Q: Per NEC 590.6(A)(3), All 125-volt and 125/250-volt, single-phase, 15-, 20-, and 30-ampere…
A: The National Electrical Code (NEC) is the most widely adopted Code in the world which is Approved by…
Q: what does the code letter on a motor nameplate refer?
A: The code letters on an electric motor gives some of the very important details of the motor. Such…
Q: Provided the bus-bar arrangement below, provide the following: a. Name the bus-bar arrangement; b.…
A: An electrical bus bar is a conductor or a group of conductor used for collecting electric power…
Q: How are occupants alerted to the presence of carbon monoxide and natural and propane gas
A:
Q: What is the total number of systems?
A:
Q: 1. What motor is used in the washing machines? Explain in detail the construction and working of the…
A: Motor used in the washing machine is Universal motor. The universal motor is an…
Q: Answer the Following questions: 1- Draw wiring diagram of domestic refrigerator, showing the main…
A: We are authorized to answer one question at a time, since you have not mentioned which question you…
Q: 11.a. Which of the following is a point where a grounding electrode conductor connection must be…
A: Answer 11 (a) : According to national electrical code 250-(96), Grounding electrode conductor…
Q: The wording that I am running into with questions such as "The number of conductors required to be…
A: The number of conductors required to be installed between three-way and four-way switches is white…
Q: 18. How many electric meters are provided for this residence?
A: As per the bartleby rule you can ask only one question at a time so please ask other question…
Q: Why the commercial unit of electrical energy is used for billing purposes instead of joules?
A: We are authorized to answer one question at a time, since you have not mentioned which question you…
Chapter 42. Electronic Signal and Security Systems
6. Why are flashing light warning units used?
Step by step
Solved in 2 steps with 2 images
- What is the meaning of "system redundancy" in aircraft electrical systems? Explain why system redundancy is important. (Minimum of 200 words)15. What does a grounding symbol on a construction drawing convey?A. A single ground rodB. A grounding electrode systemC. A ground-fault current pathD. An equipment grounding conductorA residential air-conditioning unit is installed in the attic. a. Is a lighting outlet required? __________ b. What Code section applies? __________ c. If a lighting outlet is required, how shall it be controlled? __________ d. What Code section applies? __________ e. Is a receptacle outlet required? __________ f. What Code section applies? __________
- What is the total number of systems?QUESTION 4 a) State three each: “ DOs “ and “ DON'Ts “ associated with electrical equipment operation on board ship. b) Differentiate between open circuit fault, earth fault and short circuit fault. Which of these has the most devastating effect and why?Block diagram of Arduino car Detector and explain operating
- What are the different Impedance matching devices?What is Bus Bar in electrical engineering?Who has the responsibility for Code interpretations? When are rules in the PEC mandatory and when are they advisory? What color-coding is required on multiwire branch circuits? What is the basis for figuring the general lighting loads in occupancies?