Which one of the following statement is not correct with respect to FIR filter. FIR filter is also termed as all zeros filter FIR filter has better amplitude response with lesser order as compered to IIR filter. In FIR filter the present value of the output does not depend on the past values of the output FIR filter is also termed as filter without feed back

Q: Two shunt generators operate in parallel to supply a total load current of 3,000 A. Each machine has…

A: In this question we need to find the load voltage and the armature current of each machine.

Q: in few steps how can the active sensor work as mixer device ?

A:

Q: An a differential pulse code modulated system, the transmitted bits per sample is 7.  How many…

A: number of quantization level given by 2nwhere n is no of bits

Q: I need to answer this Electronic question first please choose the correct answer and type in…

A: Biasing changes the depletion region.

Q: Explain the importance of brown-out detection in microcontroller systems.

A: Brown-out detection is a crucial feature in microcontroller systems that helps ensure the reliable…

Q: Discuss the different types of transistors used in microchips and how they work.

A: Microchips, also known as integrated circuits, are miniature electronic devices that house…

Q: Which statement is not true for a source encoder? a. reduces the size of the data b. Converts…

A: The source encoder uses the following rules: The source encoder is liable for compacting the…

Q: Explain the operation of the PCM encoder used in module ED-2960F

A: Pulse Code Modulation (PCM): PCM is a method used to define sampled analog signals digitally. It is…

Q: What is meant by sensor bias voltage?

A: Bias voltage is defined as the amount of voltage  that an electronic device needs in order to power…

Q: Describe the role of analog-to-digital converters (ADCs) in Microchip microcontrollers and their…

A: To describe:the role of analog-to-digital converters (ADCs) in Microchip microcontrollers and their…

Q: What sets field programmable gate arrays different from other semiconductors?

A: In the given questions we need to tell about that why the FPGA is better than the other…

Q: A. Draw the maximum point detector circuit and sketch the output waveform for the input signal of…

A:

Q: Define BPSK.  How do we represent binary signals in BPSK?

A:

Q: Explain driven LCR circuit?

A: Explain driven LCR circuit?

Q: When does maximum frequency deviation occur in an FM signal? -It occurs during the transition of…

A: The explanation is as follows.

Q: What sets field programmable gate arrays different from other semiconductors

A: In the given questions we need to tell about that why the FPGA is better than the other…

Q: What sets field programmable gate arrays different from other semiconductors

A: In the given questions we need to tell about that why the FPGA is better than the semiconductor…

Q: Discuss the historical evolution of microchips and their significance in the development of modern…

A: Discuss the evolution of microchips and their significance in modern electronics.

Q: What is the effect of the gate current in the operation of the TRIAC?

A: The TRIAC is defined as the triode for the alternating current. The triac is just like the set of…

Q: Difference between active high and active low pin?

A: The solution can be achieved as follows.

Q: draw a qpsk demodulator circuit with different circuit components not a block diagram.

A: According to the question, we need to draw a QPSK demodulation circuit.

Q: DRAW THE STATE DIAGRAM OF THE FOLLOWING BINARY SEQUENCE DETECTORS: 1. 11OO1 2. 11 AND/OR 00 3. OOIO1

A: 1. State machine diagram of 11001 is shown in below figure,

Q: Explain quantization noise in PCM System, and how it can be minimized?

A: we need to explain quantization noise in PCM System, and how it can be minimised .

Q: Draw a 3-bit flash converter with Vref= 12V a.Determine the full-scale range. b.Determine the code…

A: The solution can be achieved as follows.

Q: Which of the following parameters is not observed on a dynamic curve oscilloscope display? a. the…

A: 1. We need to tell which of the following parameters is not observed on a dynamic curve oscilloscope…

Q: What is the appropriate display type (common anode/common cathode) that must be used with 7447…

A: LED display can be broadly classified into two types  (i) Common Anode  In common Anode type display…

Q: 2. Look up the Texas Instruments datasheet for LS08 (or SN7408). What is the recommended voltage for…

A:

Q: A Voltage to Frequency Convertor (VCF) consists of a voltage controller oscillator (VCO), a gate…

A: In the question following data is given Output Frequency/input measured voltage = 100 and 200 pulses…

Q: What are the main advantages of Delta Modulator over PCM?

A: Pulse code modulation (PCM) and delta modulation (DM) are both extremely efficient. However, delta…

Q: fm Q5: A carrier signal of frequency 91 MHz is frequency modulated by a sine signal of amplitude 10…

A: We need to find out the bandwidth for FM signal .

Q: Question: A 1-phase full bridge inverter can operate in load commutation mode in case load consists…

A: A single phase bridge inverter can operate in load commutation mode in case load consists of  1.…

Q: What type of MOSFET is IRF640?

A: We need to tell about the type of given MOSFET.

Q: Describe the function of a Voltage Reference in ADC operations within a microcontroller.

A: In the context of analog-to-digital conversion (ADC) operations within a microcontroller, a Voltage…

Q: Draw a 3-bit flash converter with Vref= 12 ?. a.Determine the full-scale range. b.Determine the…

A: The solution can be achieved as follows.

Q: How should the initial data be erased from an EPROM?

A: Erasing the initial data from an EPROM (Erasable Programmable Read-Only Memory) requires a specific…

Q: What is the principle of the method for direct digital synthesis (DDS) of analog signals?

A: We need to explain the principle of the method for direct digital synthesis (DDS) of analog signals.

Q: What is the function of en able an input multiplexer chip 2 To apply Vec connect ground A/ O 2) To…

A:

Q: Determine the outputs at the BCD indicators for each of the five input pulses shown in Figure 3.

A:

Q: Please describe as simply as possible in detail, what a multiplexer circuit is, how it works. Please…

A:

Q: 4) a) Draw a diagram showing the following circuits 1: Ring, Radial and Spur circuits, label…

A: a) The labeled diagram of the radial circuit is shown below:  The labeled diagram of the spur…

Maximum power transfer theorem

A resistive load will consume maximum power from a network when the load resistance is equal to the resistance of the network as viewed from the open-circuit terminals, with all energy sources removed leaving only the internal resistances. Physicist Moritz von Jacobi introduced the maximum power transfer theorem in 1940. Therefore, this theorem is also known as Jacobi's law.