Which of the statements/is/are true concerning the friction factor for solid spheres and cylinders immersed in a flowing fluid? I. Such friction factors are traditionally referred to as (dimensionless) drag coefficient denoted by CD. II. At Reynolds number much as less than 1, the relationship CD=24/Re is valid and CD is inversely proportional to Re. III. The characteristic area A* used in the definition of these friction factor is the surface area of the object. Statement I only Statement II only Statement III only Statement I and II only All three statements are true

Which of the statements/is/are true concerning the friction factor for solid spheres and cylinders immersed in a flowing fluid? I. Such friction factors are traditionally referred to as (dimensionless) drag coefficient denoted by CD. II. At Reynolds number much as less than 1, the relationship CD=24/Re is valid and CD is inversely proportional to Re. III. The characteristic area A* used in the definition of these friction factor is the surface area of the object. Statement I only Statement II only Statement III only Statement I and II only All three statements are true

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.26P

See similar textbooks

Similar questions

Qustion. An aircraft is flying in level flight at a speed of 200 km/h through air (density, p = 1.2 kg/m³, and viscosity, μ = 1.6 x 10-5 N-s/m²). The lift coefficient at this speed is 0.4 and the drag coefficient is 0.0065. The mass of the aircraft is 800 kg. The effective lift area of the aircraft NOTE= Do not give wrong answer I will dislike , If not sure skip it
8.) A circular cylinder 4m long and 3m in diameter is in an air stream. The flow velocity is 5 m/s L parallel to the axis of the cylinder. Given that the coefficient of drag, CD on the cylinder is 1.3, and the density of air is 1.225 kg/m3. What is the force on the cylinder? A. 0.090 KN B. 0.14 KN C. 0.24 KN D. 0.91 kN
2. Outcomes 1 and 4.Show and explain all work. You must show and explain all work. The drag on the hull of a sailboat can be shown to depend on the boat velocity V, the water density p and viscosity μ, the length of the hull f, and the acceleration due to gravity g. JIH Class 40 Racing Yacht. 30
1. The given information is as follows: Cd=1.4 (coefficient of drag) ¥=10 ft/sec (velocity) Ƴ=62.4 #/ft3 g=32.3 ft/sec2 a. What is the water pressure in PSF against the obstruction? b. If the pier is 6 ft wide and 14 ft deep, what is the Resultant Pressure on the WHOLE obstruction? c. If the obstruction is fixed into the bottom of the river (mud line), what is the bending moment at the mudline on the obstruction?
A sphere (Cd = 0.2) 1 ft in diameter travels at 100 ft/sec in standard atmospheric air. What is the drag force? A. 0.0117 lbf C. 0.0712 lbf B. 0.0217 lbf D. 0.0127 lbf
The Reynold's number of a sphere falling in air is 1E6. If the sphere's radius is 1ft, what is its velocity? Density of air is 0.00234 slug/ft³ and viscosity of air is 3.8E-7 lbf-sec/ft²A. 2.5 ft/sB. 5.1 ft/sC. 40.6 ft/sD. 81.2 ft/s
= 3570 T AC =144 Example: 1.5 ft It is desired to determine the drag force at a given speed on a prototype sailboat hull. A model is placed in a test channel and three cables are used to align its bow on the channel centerline. For a given speed, the tension is 40 lb in cable AB and 60 lb in cable AE. Flow 4 ft Determine the drag force exerted on the hull and the tension in cable AC. Choc ug the h- as the free hod- DApress the
#4 1.11 For a small particle of styrofoam (1 lbm/ft) (spherical, with diameter d = 0.3 mm) falling in standard air at speed V, the drag is given by FD-3mVd, where is the air viscosity. Find the maximum speed starting from rest, and the time it takes to reach 95 percent of this speed. Plot the speed as a function of time. s) Answer: (Vmax=0.0435",t=0.0133 S
What is used as a similarity parameter to help determine whether the flow in a body and its scaled version are aerodynamically similar? Similarity Coefficient Mach Number Skin Friction Drag Coefficient Reynolds Number Thank you.
An airplane that has a cross-sectional diameter D = 4 m of the front portion is to fly at a speed of 600 km/hr in air that has a density of 1.1 kg/m and dynamic viscosity of 1.27 x 10 Pa.s. A small size model of scale ratio (1/17) to be tested in a different fluid that has a dynamic viscosity 5 x 105 Pa .s and a density of 500 kg/m2. It is determined that the parameters that are important for this test are: diameter D, density, viscosity, velocity V, the length of the wings L and the drag force F. What must be the speed (m/s) of the model to Choose... ensure dynamical similitude? What must be the corresponding diameter of the model (cm)? Choose.. What is the number/s of dimensionless groups for this problem? Choose...
11 Assuming Stoke’s Law applies, a. Calculate the velocity of a 1.8 cm NaCl particle (S.G = 2.16) falling in water (viscosity is 1.1 cP). b. Calculate the drag force and drag coefficient for this particle.
1 (a) A plate 0.05mm distant from a fixed plate moves at 1.15 m/s and required a force per unit area of 2.7 N/m2 to maintain this speed with using an oil of specific gravity 0.75. Find the dynamic viscosity and kinematic viscosity of the fluid between the plates. 1 (b) Calculate the specific weight, density, and the specific gravity of a liquid having a volume of 665150 cm³ and weight of 71 kN (ENTER ONLY THE VALUES BY REFERRING THE UNITS GIVEN) 1 (a) The dynamic viscosity of the fluid (in Centipoise) The kinematic viscosity of the fluid (in stokes) 1 (b) Specific Weight in (kN/m3) Density of liquid (in kg/m2) Specific gravity of liquid Windows bu