Which of the following units could NOT be used for normal strain? O μm/m Oyd/yd O μmm/m Ο μg/kg O μin./in.

Q: Determine the hydrologic risk

A:

Q: ACTIVITY (NODES) IMMEDIATE DURATION (DAYS) A. 20 В 10 A 15 B 15 26 A 15 G 40 H 50 A 20 E,G,H 6. K…

A:

Q: Activity 1. From the rectangular area shown a semi-circle of radius 4 cm is removed. Locate the…

A:

Q: A trip table (veh./hr) needs to be loaded on the network shown in the table below. Find the total…

A: Step 1:Step 2:

Q: Station Cut End Area (ft²) 10+00 234 11+00 369 12+00 441 13+00 408 14+00 271 15+00 108 Part A For…

A:

Q: Situation A. Control Survey An equilateral triangular track of land has a length of one of its sides…

A: Given:-  An equilateral triangular track of land has a length of one of its sides equal to 8600 m…

Q: A plot with the shape of a trapezium has the following measurements Long side: 52 m Short side: 24 m…

A: The given data is shown below: Trapezium"Long side=52 mShort side=24 mPerpendicular…

Q: Txs Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an…

A: Given data:- σxA,B=59.2σsA,B=118.5τxsA,B=118.5 Below diagram is given;

Q: Question 6 6. To find the distance across a small lake, a surveyor has taken the measurements as…

A:

Q: E D А B P T

A: Static friction is contact between at least two strong masses that are not moving comparative with…

Q: A schedule is an organized sequence of events that identifies all parts of the work to be done. O…

A: Schedule is the organizes tasks, resources, and deadlines in the ideal order for the project to be…

Q: From the following measured interior angles of a five sided figure: Station Values of Angles (J No.…

A: To find :

Q: A distance of 300 m is to be laid-out using a tape having an incorrect length of 29.98 m. How much…

A: Given, Distance to be measured, say D = 300 m Actual/incorrect length of tape, L' = 29.98 m   To…

Q: Given an adjustment containing the following: Number of Control Stations 1 Number of Unknown…

A:

Q: can u pls do the question 2 and 3

A:

Q: Situation C. Using the figure, supply the data needed in the numbered cell. BS FS 1.27 4.91 BS FS…

A:

Q: centroid C of the beam having the cross-sectional area shown 150 mm 150 mm 20 mm 20 mm B

A:

Q: A distance between point (A) and (B) is (170m) was measured by a tape of (20m) length, the it was…

A: L=20m

Q: The five-bolt connection must support an applied load of P = 1600 lb. If the average shear stress in…

A:

Q: According to the information in the following arrow network, determine the following: The T.F. of…

A: Step 1

Q: please calculat the angles and complete the following table. Ba A 零方向 Survey Survey Targe Reading…

A: ANSWER:-

Q: Q1/A/ What is the Surveying? Write down the steps for working on a survey works. B/ Mention the…

A: Surveying is a branch of civil engineering and the steps involved in the work of the survey of the…

Q: Determine the area bounded by a straight road and an irregular boundary using the data given below:…

A: The best method applicable for determination of area of irregular boundaries is Simpson's rule.…

Q: Two level sections of 35-m stations with center heights of 1.36 and 1.55 m in cut, base width 15 m,…

A: The distance between the two stations, L = 35m The base width, b = 15m The height at station 1 is,…

Q: Determine thex- and y-coordinates of the centroid of the shaded area shown. 4" 4" 6" -2.00" 2.00"…

A:

Q: Aerial photography is to be taken of a tract of land that is X-mi square. Flying height will be H ft…

A:

Q: Survey Sarvey Targe Average value after CLR zero with multiple rounds Reading Average Valne after…

A: The angular measurement is the process of determining the direction of a line with reference to any…

Q: Don't need to show work, just need to know which ones correct to compare my answers. 3/4

A: This question is related to the Building design and drawing from Civil Engineering. In this question…

Q: -60 20 10 40 100- 10 -30 -15- 60

A: THE BASIC COMMANDS USED ARE 1. LINE 2. CIRCLE 3. OFFSET 4. XLINE 5. DIMENSION 6. LAYER

Q: aseholds going to cover in the city. (1 mile = 5,280 feet) (chc closest answer) Total of 400…

A: The given data in the question is: Total of 400 households All employments and exchanges are at…

Q: estimate is used by a prospective owner of a project to determine the approximate cost of a project…

A: Conceptual estimates are developed early in the project planning phase and are based on limited…

Q: The correct answers given are: 1)  480.18 2)  28.92 Can I please have assistance to show the…

A: Torque = 6.3 kN-m or 6.3 x 106 NmmLength of the shaft = 3m or 3000 mmCross-sectional area, A= 5090…

Q: View Policies Current Attempt in Progress (a) Con. 3) In the accompanying figure, the area of the…

A:

Q: 14.  From a point on level ground 199 feet from the base of a tower, the angle of elevation of the…

A:

Q: questions by completing the tabulation below. What is the computed departure of line DE?

A:

Q: 3. Draw a new arrow network by correcting the redundant dummy activity (or activities) in the…

A:

Q: B. 0.9m 900 N 0:6m 2.4 m 2000 N 0.6 1.8 1.8

A:

Q: unit rate of 51 minutes/ 6 miles

A:

Q: Double integration method Find reaction A, B, and C

A:

Q: Convert 109° 46' 51" to degree decimals. Round your answer to 3 decimal places. Do not include units…

A: To convert in degree decimal

Q: ▼ Part A Station 10+00 11+00 12+00 13+00 14+00 15+00 Cut End Area (ft²) 239 358 454 401 272 106 For…

A:

Q: IIL Complete the horizontal angle measurement note Result Reviewer Sight Reading Angle Face to 11 A…

A:

Material Properties

Construction in civil engineering demands high strength, durability, and longevity. These targets can be achieved by better design and analysis, along with the correct choice of materials. Different materials have different properties and hence, they respond and performs differently under the various condition of external loadings. It is therefore a critical task of an engineer to select the right material based on the property that the material is supposed to function in real-time. When speaking about the property, there are different categories of material properties like chemical property, physical property, mechanical property, electrical property, magnetic property, thermal property, etc. These material properties form the basis of material selection in various applications.