Q1/A/ What is the Surveying? Write down the steps for working on a survey works. B/ Mention the types of units of distance measurements with examples. C/ Mention the methods used to measure the area of Irregular places.

Q1/A/ What is the Surveying? Write down the steps for working on a survey works. B/ Mention the types of units of distance measurements with examples. C/ Mention the methods used to measure the area of Irregular places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: e of water in the reservoir. The numbers on the plot show the horizontal distances (m) which were…

Q: In the accompanying plot the boundary of the water surface of a reservoir is shown by irregular…

Q: A parcel of land is to be subdivide into parts and the Engineer got this data below. Calculate the…

Q: 2.A hydrographic survey of a lake generated the following approximate measurements: 16,500 sq m =…

Q: The parcel of land is shown with the coordinates at points A (9x,0), B, C, D, and origin at point O.…

Q: A surveyor set his instrument up at point Ain order to observe point B. The instrument was inclined…

A: To find :D(Inclined) = Slope distance between the center of the instrument…

Q: Item 3 On a vertical photograph of flat terrain, the scaled distance between two points is ab. Find…

A: Part-APhoto distance (ab) = 1.46 in. Map distance (AB) = 4.56 in. Scale of Map (Smap) = 1:9600…

Q: 10. An agricultural land was measured using a 100 m tape which was actually 0.02 m short. If the…

Q: Calculate the area (in sqm) of the cross-section of ranges DF. (Type your answer using 2 decimal…

A: To determine Area of section Df

Q: Q1: The reading obtained being as shown below, calculate the elevations (R.L) of all points, and…

A: To find elevation of all points

Q: Surveying subject : a. Explain the principles of surveying? Support your answer with sketches. b.…

A: A. Principles of surveying: The following are the 2 principles of surveying: 1. Working from whole…

Q: Question 6 6. To find the distance across a small lake, a surveyor has taken the measurements as…

Q: Q1/A/ What is the difference between Geodetic Surveying and Plan Surveying? B/ Mention the types of…

A: The process or technology of scientifically measuring points on, above, or below the surface of the…

Q: The distance AB was measured using proper taping procedures. The forward measurement was recorded as…

A: LAB = 725.895m (measured) LBA = 725.750m (measured) The measurement of distance AB L = 0.5(LAB+LBA)…

Q: In the accompanying plot the boundary of the water surface of a reservoir is shown by irregular…

A: Calculating the mid section area: Area of section FG:…

Q: ubject: FUndmentals of Surveying Derive the formula of Long Chord (LC) , Tangent Distance (T),…

A: lets draw the horizontal curve with radius R and the deflection angle ∆ Long Chord (L): The…

Q: Discuss the following items briefly. 1. How is a meter defined by a standard? 2. Describe how…

Q: A line 100m long was paced by a surveyor for four times with the following data, 142, 145, 145.5,…

A: Given values - Length of the 1st line = 100m In first trial paced values are 142, 145, 145.5,…

Q: 8. True or False. If false, then explain why the premise is false. a. b. C. The most important…

A: Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: In the accompanying plot the boundary of the water surface of a reservoir is shown by irregular…

A: To determine Areas (m²) of the cross sections of ranges BC, DE, and FG. Volume (m³) of water between…

Q: Do not copy the answer here in bartleby. Give clear solutions UPVOTE WILL BE GIVEN. Please write…

Q: Subject: engineering surveying c. Describe with the help of diagram, how you would make a…

A: Chain surveying is method of surveying in which linear measurements are taken on the field. This is…

Q: Question 3 A survey opens an old map plotted to a 10 m to 1 cm scale. He used a planimeter to find…

Q: Determine the probable error and relative precision of the underlined distances and the mean of the…

Q: History of surveying When did it begin How did it begin Why did it begin Where did it begin

A: Structural designing alludes to the structure of constructions or frameworks in the indigenous…

Q: Q- A survey opens an old map plotted to a 10 m to 1 cm plan's area and measure it as 124 cm². If he…

Q: please calculat the angles and complete the following table. Ba A 零方向 Survey Survey Targe Reading…

A: ANSWER:-

Q: (c) SURVEY- PROBLEM, A surveyor measured the distance between two points marked on a plan drawn to a…

A: Given data- Scale 1 cm=1 m, Measured distance=50 m, Wrong scale 1 cm=0.5 m, Measured area = 60 m2,…

Q: Given in the accompanying tabulation are the adjusted latitudes and adjusted departures of a parcel…

A: Find bearing of dividing line FC Area of CDEF

Q: In the accompanying plot the boundary of the water surface of a reservoir is shown by irregular…

A: To calculate The Areas between the cross sections of the Reservoir at BC, DE, FF. Area at A & H…

Q: SURVEY- PROBLEM, A surveyor measured the distance between two points marked on a plan drawn to a…

Q: H = 3525 m; f = 90.90 mm; h = 747 m Express your answer to five significant figures. 197| ΑΣΦ ↓↑ vec…

Q: A surveying instructor sent all the 40 students in his class out to measure a distance between two…

A: Relative precision of the mean is the ratio of probable error of mean to the most probable value of…

Q: Line AB = 250m long and was paced five times by the surveyor and recorded as follows: Another line…

A: Formula used - Totsl Distance = Pace factor ×Avergae of paces For the first paced distance - 250…

Q: PROBLEM A surveyor set his instrument up at point A to observe points B and C which are both ahead…

Q: Q- A survey opens an old map plotted to a 10 m to 1 cm scale. He used a planimeter to find the…

A: Given data- Measurement by planimeter- Plan Area = 124 cm2, Due to shrinkage, 20 cm length measure…

Q: As shown in the figure below, point A and point B are both sides of the river, but the point B…

A: Let the point C is observed opposite to point C. Draw the figure,

Q: Based on the survey notes below, fill in the necessary data to answer the next set of questions. All…

A: Reduced level :- Elevation of a point with respect to mean sea level is called Reduced Level.Back…

Q: An 8m steel tape was purchased and advertised as follows: Standard temperature 24°C : 7.5kgs 0.60…

Q: A 26.6 B103 C 23.7 26.9 22.1 -19.1 16.9 28.0 D 22.0 21.8 13.8 22.4 20.3 9.0 109 29.9 F G 18.3 12.6…

Q: Q3: The polygon traverse ABCDEA shown in figure 2. is to be divided into two equal areas by a…

Concept explainers

Control Survey and Geodetic reductions

Control surveys or survey controls are used to establish reference points as a basis for various construction activities. Vertical and horizontal control points are to be established in a control survey to increase accuracy. After establishing the control points, all other types of surveys such as topographic, right-of-way, aerial mapping, construction layout, boundary surveys, and utility mapping can be worked upon so that control networks can be formed. The place from which the observations are made is called a survey station.

Question

100%

Q1/A/ What is the Surveying? Write down the steps for working on a survey works.
B/ Mention the types of units of distance measurements with examples.
C/ Mention the methods used to measure the area of Irregular places.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Steps of Surveying

VIEW

Step 3: Types of Units of Distance Measurement

VIEW

Step 4: Methods Used to Measure Area of Irregular Places

VIEW

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question - What is surveying and what are its two principles?
You're a new engineer reviewing length measurements from a land surveying project. You're suspicious about a length measurement recorded as 300 ft. With no decimal point or notation, you're not sure whether or not the two trailing zero's are significant. You inquire with the survey crew who performed the measurement and found that the recorded value was taken by experienced surveyors using an instrument accurate to two-tenths of a foot and calibrated the morning of the survey. Based on the information you have, which of the following scientific notation expressions would best represent the accuracy of the length measurement? Group of answer choices 3.00E2 ft 3E2 ft 3.0E2 ft
SurveyingDraw also the figure
If numbers collected from a survey are measurements, what are these measurements called before you perform any calculations?
What are some common methods used for volume calculation in surveying?
Q1The table below contains the cross- sections Areas of road Calculate the volumes of the earth work Distance(m) 0 30 60 120 180 Areas (m?) 48.000 37.500 25.345 13.854 14.145 Q2The areas within the contour lines at the site as follows: Calculate the volume of water between them Contour m 90 88 86 84 82 80 78 Areas m? 476O 4310 3770 2960 2190 1640 8400 *
The solutions and answers should have minimum of 3 decimals for linear measurements and should be in Degree-Minute-Seconds (2 decimals for seconds) for angular measurement, if not whole number. An engineer is tasked to measure a whole line multiple time. Since the length of the line is significantly longer than the steel tape, the engineer decided to measure the line in three segments. First, the engineer measures a 50m known line using the steel tape and find out that the tape is too long with the observation having only 49.2m. With these values, the correction factor of ???? = 50? − 49.2?. After determining such corrections for future calibration, the engineer measured each segments. The following are the observations: 1st Segment: 46.2m, 46.3m, 46.5m; 2nd Segment: 48.3m, 48.2m, 48.1m; 3rd Segment: 32.3m, 32.6m, 32.4m. Determine the complete expression of the most probable value (together with probable error) of the line.
The paper of an old map drawn to a scale of 100 m to 1 cm has shrunk so that a line originally 10 cm has now become 9.4 cm. There was also a note on the plan that the survey done with Gunter’s Chain was 10 cm too short. If the area measured now is 65 sq- cm. Find the correct area on the ground in sq- cm and sq- km.? If any data is missing you can assume it yourself.
Show complete formulas and solutions. Round off to 3 decimal places for lengths. Angles must be in degrees, minutes, and seconds (° ‘ “) and seconds should not include decimals anymore (ex. 1°1’36.52” should be 1°1’37”).
Help pleaseee, Fundamentals of Surveying how many significant figures are present in the following? type answer in numerical form: example 1,2,3 32.25 = 0.24 = 3.6 = 0.0024 = 0.000005 = 12.3 = 100 = 12345 = 0.001 = 155.28 =
Q1: The reading obtained being as shown below, calculate the elevations (R.L) of all points, and check your results. point B.S L.S F.S H.I Elevation Remarks 1 2 3 1.622 34.82 1.874 0.354 36.34 2.032 1.780 36.592 4 2.362 5 0.984 1.122 36.454 6 1.906 2.824 35.536 7 2.036 33.500 В.М
Accuracy and Errors The area of a plan of an old survey plotted on a sheet is found to have shrunk so that a line originally 10 cm long now measures 9.7 cm only. Calculate the shrinkage factor.