When the three identical star-connected coils are supplied with 400 V, 50 Hz, 3- o supply, the 1- p wattmeter whose current coil is connected in line R and pressure coil across the phase R and neutral reads 8 kW and the ammeter connected in R- phase reads 36 Amp. Assuming RYB phase sequence find: (i) the power factor, of the load , (ii) resistance and reactance of the coil (iii) reactive

When the three identical star-connected coils are supplied with 400 V, 50 Hz, 3- o supply, the 1- p wattmeter whose current coil is connected in line R and pressure coil across the phase R and neutral reads 8 kW and the ammeter connected in R- phase reads 36 Amp. Assuming RYB phase sequence find: (i) the power factor, of the load , (ii) resistance and reactance of the coil (iii) reactive

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of158 volts, 50 Hz supplies the combination. Determine the following:a. Circulating currentb. Voltage across the resistorc. Voltage across the capacitord. Real power supplied by the source
Section [Section Upload answer sheets Find the following parameters of an ac voltage given by the equation v-100sin370t.Find RMS value,form factor, peak factor, average value and frequency. E Submission
A single phase 120V AC sourc controls power to a resistve load 20N using integral cycle control. a) Find the output power for both output voltage waveforms shown below. b) The voltage and the current ratings of the switch. c) The duty cycle and the value of TON to produce 0.63KW power. d) The power factor for part (c). Awww TON -TON
8 = 0 Q1: What does happen if we change two currents? Q2: What does happen if we have a three-phase four poles machine? a Q3: What does happen if we have a two-phase two poles machine? Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali K....p. . --
Q2/3-phase.E.W.C. R using center tap transformer supplies highly inductive load, find: 1. The average load voltage with and without FWD and discusses these cases. 2-lf firing angle equal to 45°, the supply voltage is240v, transformer ratio is (2/1). Calculate the DC current& voltage of this case. 3- Draw all waveforms diagram. 4- what are the difference between the type of connection (Delta or Star).
The step down DC chopper uses DC source voltage V(dc) = 200 V and resistive load impedance of 10 ohm. The duty cycle is 0.4 the voltage drop across the switch may be taken as zero, Calculate : (a) Average and RMS value of output voltage. (b) Average and RMS value of output current.
Q9. What is the basic principle that a cage winding can be represented by a three-phase winding? Give your explanation.
Does Clampor circuit change the peak-to-peak (i.e., rms value)? Justfy
Generate a conclusion on this following statements: Determine and analyze the voltage regulation characteristics of the alternator with resistive, capacitive, and inductive loading.
J12 J952 Q.11: For the coupled circuit shown if Vs-10020°v: 1. Compute the complex value of currents i & i2. 2. Find the consumed power in each J42 k=0.75 Vs I2 52 32 branch. (Ans.: P2=1166.4W, P3=432W Ps=751.5W)
1- Derive expression for the output rms voltage for single phase ac voltage controller with resistive load
The voltage regulation of an alternator having 0.75 leading p.f. load, no-load induced e.m.f. of 2400V and rated terminal voltage of 3000V is............... percent. *