When discussing CV axle replacement, Technician A states that once a CV boot is torn the entire CV joint must be replaced. Technician B states that CV joints are lubed for life and should require no maintenance. Who is correct? Technician A Technician B Both Technician A and B Neither Technician A or B

When discussing CV axle replacement, Technician A states that once a CV boot is torn the entire CV joint must be replaced. Technician B states that CV joints are lubed for life and should require no maintenance. Who is correct? Technician A Technician B Both Technician A and B Neither Technician A or B

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter40: Drive Axles And Differentials

Section: Chapter Questions

Problem 7ASRQ

See similar textbooks

Similar questions

While discussing the possible causes for a clunking noise duiing acceleration: Technician A says that an outer CV joint could be the cause. Technician B says that insufficient runout of the drive axle may be the cause of the problem. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
The CV joint boots on the left side of a vehicle appear to be squeezed together; the boots on the right side of the vehicle appear to be stretched apart. Technician A says that one or more of the engine/transaxle's mounts may be broken. Technician B says that one or more of the engine/transaxle's subframe mounts may be broken. Who is correct? O a. A only O b.B only C. Both A and B O d. Neither A nor B
Which of the following describes the double-Cardan universal joint? a. It is most often installed in front-engine rear- wheel-drive luxury automobiles. b. It is classified as a constant velocity U-joint. c. A centering ball socket is inside the coupling yoke between the two universal joints. d. All of the above.
Which of these is the best way to determine which CV joint is faulty? a. Squeeze test b. Runout test c. Visual inspection d. Road test
Draw FBD of Bicycle axle (Thru axle)
Which of the following CV joint tests should be performed to determine if the CV joint needs to be serviced? a. balance test b. chassis test c. squeeze test d. spin test
Identify the zero force members (if any) in 3 kip H. 2 kip- 3 kip T. 8 ft -1.5 kip- 4 ft |B TC ID -10 ft-10 ft-10 ft- 10 ft-
When reviewing the service procedures for CV joints and drive axles, Technician A says that the axle can be used as a slide hammer to help remove a stubborn inboard joint from the transaxle. Technician B says that a drive axle should never be allowed to hang by its own weight during removal or installation. Who is correct? O a. A only Ob.B only O c. Both A and B O d. Neither A nor B
True or False. In some applications, the grease seal is a press-fit into the axle housing, which is stationary, and seals against the axle shaft, which is rotating. Selectone: True False
While diagnosing the cause of a clicking noise that is heard only when the car is turning: Technician A says that the most probable cause is a worn wheel bearing. Technician B says that the most probable cause is a worn outboard CV joint. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
Which of the following statements about unibody construction is not true? A unibody is a stressed hull structure in which each of the body parts supplies structural support and strength to the entire vehicle. Unibody vehicles tend to be tightly constructed because the major parts are all welded together. All unibodies are constructed from steel. Most front-wheel-drive unibody vehicles have a cradle or partial frame.
When checking the front end, which of the following are NOT cause for rejection? Bearing cap is broken or missing or if there are any cracks or welded repairs to any components. Front axle is bent or gear box mounting is loose, bolts are missing, or bolts or case are cracked. All of the statements shown are cause for rejection. The steering damper leaks, is loose, mount is cracked/ broken, or is missing or steering shaft coupler/universal is binding, frayed, or cracked.