When a round bar material with diameter of 37.5mm, length of 2.4 m, Young's modulus of 110 GN/m² and shear modulus of 42 GN/m² is stretched for 2.5 mm, its bulk modulus will be nearly (a) 104 GN/m² (c) 84 GN/m² (b) 96 GN/m² (d) 76 GN/m²

When a round bar material with diameter of 37.5mm, length of 2.4 m, Young's modulus of 110 GN/m² and shear modulus of 42 GN/m² is stretched for 2.5 mm, its bulk modulus will be nearly (a) 104 GN/m² (c) 84 GN/m² (b) 96 GN/m² (d) 76 GN/m²

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The following observations were made during a tensile test on a mild steel specimen 40 mm in…

A: Given data : Tensile load P=40 KN Change in length ∆L=0.0202 mm Initial length L=200 mm Diameter of…

Q: Test No Temperature C Deformation rate(mm/min) Strain at break Youngs modulus (Gpa) Stress at…

A: Step 1: UTS mean Ultimate tensile strength. From the conventional stress strain curve, it is…

Q: ven the stress-strain data from a tension test, how do you find the following : a) The modulus of…

A: Solution on below attachments

Q: 5. A tensile test was done on a magnesium sample of original diameter and original length of 12mm…

A: To plot the stress v/s strain curve and to find the required parameters Note: as per the answering…

Q: A specimen is originally 300mm long and has a diemter of 11mm and it subjected to a force of 4kN.…

Q: A hot-rolled steel bar has a diameter of 12 mm was subjected to a tension test as shown in the…

A: NOTE As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost…

Q: A stainless-steel rod 16mm in diameter and 300mm long is put under a tensile load of 250 kN.…

A: Given data Initial diameter of the rod(Di) = 16 mm Then Area (Ai) = (π/4)*Di2 = 201.062 mm2…

Q: For a given material if the Young's modulus is 200 GN/m² and odulus of rigidity is 80 GN/m?, then…

A: Given data : Youngs modulus (E)=200 GN/m2Modulus of rigidity (G)=80 GN/m2

Q: When a round bar material with diameter of 37.5 mm, length of 2.4 m, Young's modulus of 110 GN/m²…

Q: 1. A vertical pressure of 70 MPa is applied to an aluminum cube sample with a length of 10 cm on…

Q: 3-21. The stress-strain diagram for a polyester resin is given in the figure. If the rigid beam is…

A: P = 80 kN or 80,000 N d = 40 mmD = 80 mm

Q: Determine the following: a. Young's modulus within the linear portion b. Tangent modulus at a stress…

A: a).Young's Modulus : At the proportional limit, stress is directly proportional to strain stress α…

Q: calculate the lateral strain and the change in diameter.

Q: Copy the sketch of the tensile stress-strain test (Figure A1) results for a waisted metallic…

A: Objective: To indicate the given points on the stress-strain diagram and calculate the Young's…

Q: A steel bar 2 m long, 20 mm wide and 15 mm thick is subjected to a tensile load of 30 kN. If…

A: we have to find the increase in volume

Q: (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar width b.

Q: A Charpy V Notch (CVN) test was performed on a steel specimen and produced the readings shown in…

A: We have been given the following values: Sr. No Temperature(C) Toughness, Joule (N.m) 1.…

Q: O (MPa) 80 60 40 20 0.002 0.004 0.006 0.008 0.01 0.012 Figure 3 i) Determine the value of yield…

A: Dear student as per bartleby guidelines we are supposed to answer only first 3 sub parts. Kindly…

Q: 2) For a specific material having poisson's ratio -0.32, the percent of elastic modulus to modulus…

Q: 3. A standard steel specimen having a diameter of 0.505" and a 2" gage length is used in a tension…

A: D = 0.505 in L = 2 in = 0.002 in E = 30,000 ksi

Q: If the lateral compressive strain in a material is 0.3 x 10-3 and the Poisson ratio is 0.25, then…

A: Lateral compressive strain-εL=-0.3×10-3μ=0.25

Q: Problem NO. 2. A student performed a tensile test in one of his samples, an aluminum specimen which…

Q: A 13 mm diameter tensile specimen has 50 mm gauge length. If the load corresponding to the 0.2%…

Q: A specimen is originally 1ft long, has a diameter of 0.5in, and is subjected to a force of 5001b.…

Q: A cylindrical tensile specimen has an undeformed diameter of 8.6 mm. It is subjected to a tensile…

A: Hello dear this is the solution of your problem The answer is found to be Change in diameter =0.37mm…

Q: The state of two dimensional stresses acting on a concrete lamina consists of a direct tensile…

A: Given data- State of 2-D stress given- Direct tensile stress- σx=1.5 N/mm2, Shear stress- τ=1.20…

Q: DURING THE STRESS-STRAIN TEST, THE UNIT DEFORMATION AT A STRESS OF 30 MPa WAS OBSERVED TO BE 110 x…

Q: A steel specimen is tested in tension. The specimen is 25 mm wide by 12.5 mm thick in the test…

A: Area=25×12.5mm2=312.5mm2

Q: niform concrete slab is to be attached to two rods whose lowers ends are initially at the same…

A: Let W be weight of concrete slab. To find area of aluminium rod

Q: 2) A given material the linear limit is 1.8 * 106 N/ m? and the ultimate compressive strength is 1.8…

Question

When a round bar material with diameter of
37.5mm, length of 2.4 m, Young's modulus of
110 GN/m² and shear modulus of 42 GN/m² is
stretched for 2.5 mm, its bulk modulus will be
nearly
(a) 104 GN/m²
(c) 84 GN/m²
(b) 96 GN/m²
(d) 76 GN/m²

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: State the given data

VIEW

Step 2: Determine the bulk modulus

VIEW

Solution

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A composite column is formed by placing a steel bar 20 mm diameter and 200 mm long, inside an alloy cylinder of the same length whose internal and external diameters are 20 mm and 25 mm respectively. The column is then subjected to an axial load of 50 kN. Modulus of elasticity for steel and alloy is 200000MPa and 70000MPa respectively. Which of the following gives the stress in the steel bar? a. 132.98 MPa b. 46.54 MPa c. 74.80 MPa d. 166.23 MPa
A 13 mm diameter tensile specimen has 50 mm gauge length. If the load corresponding to the 0.2% offset is 6800 kg, the yield stress will be nearly 1. 31 kg/mm² 2. 43 kg/mm² 3. 51 kg/mm² 4. 63 kg/mm² X
A cylindrical piece of steel, with a diameter of 60mm and length 100 mm, is subjected to an axial compressive force of 40,000 kg. If bulk modulus is 1.7 x 106 kg/cm² and poisson's ratio is 0.25 than the change in volume of the cylindrical piece is
A cylindrical piece of steel, with a diameter of 60mm and length 100 mm, is subjected to an axial compressive force of 40,000 kg. If bulk modulus is 1.7 x 106 kg/cm² and poison's ratio is 0.25 than the change in volume of the cylindrical piece is?
650 600 550 500 450 400 350 300 250 200 150 100 50 0.002 0.004 0.006 0.008 0.01 0.012 0.014 0.016 0.018 0.02 Strain mm/mm The graph above shows the stress-strain relationship of a steel bar under tension test. The steel bar diameter = 8 mm and the bar gauge length = 100 mm. Determine the following: Toughness of the specimen Stress (MPa)
The solid circular drill rod AB is made of a steel that is assumed to be elastoplastic with τY = 22 ksi and G = 11.2 × 106 psi. Knowing that a torque T = 72 kip·in. is applied to the rod and then removed, determine the maximum residual shearing stress in the rod. The maximum residual shearing stress in the rod is ksi.
When a round bar material with diameter of 37.5 mm, length of 2.4 m, Young's modulus of 110 GN/m² and shear modulus of 42 GN/m² is stretched for 2.5 mm, find its Bulk modulus.
Q.3 The compressive strength of (Ø25×25) cm cylinder is 30 MPa at an age of 21-day, determine the direct tensile strength at the age of 7-day.