What will be the tensile strength of 160 x 8 mm plate with the holes for 16 mm bolts as shown in figure? Plates are of steel grade Fe410. 1 30 mm 40mm 40mm 25 mm 2 25 mm 1 3 25 mm 2 25 mm 1 30 mm 1 160 mm 1.

What will be the tensile strength of 160 x 8 mm plate with the holes for 16 mm bolts as shown in figure? Plates are of steel grade Fe410. 1 30 mm 40mm 40mm 25 mm 2 25 mm 1 3 25 mm 2 25 mm 1 30 mm 1 160 mm 1.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SITUATION 14: A PL 300 x 20 mm is to be connected to two plates of the same material with half the thickness by 25 mm Ø rivets as shown in the figure. The rivet holes have a diameter 2 mm larger than the rivet diameter. The plate is A36 steel with Fy= 250 MPa, allowable tensile stress of 0.60Fy and allowable bearing stress of 1.35Fy. The rivets are A502, Grade 2, hotdriven rivets with allowable shear stress of 150 MPa. 25 mm Ø rivets + + PL 300x20 P/2 P P/2 PL 300x10 43. Which of the following most nearly gives the max. load in kN that can be applied to the connection without exceeding the allowable shear stress in the rivets? a. 675 KN b. 490 KN c. 598 KN d. 790.5 kN 44. Which of the following most nearly gives the max. load in kN that can be applied to the connection without exceeding the allowable bearing stress between the plates and the rivets? a. 490 KN b. 675 KN c. 598 KN d. 790.5 kN 45. Which of the following most nearly gives the max. load in kN that can be applied to the…
What is the approximate value of the tensile strength governed by yielding of the cross- section of a roof truss diagonal 100 x 75 x 6 mm (fy = 250 MPa) connected to the gusset plate by 4 mm welds as shown in figure? (Take partial safety factor as 1.10) 1 H 100 4 mm weld, 140 mm long 75 A₂ = 1010 mm² Weld 310 mm long
What will be the block shear strength of a tension member as shown in figure below? The steel is of grade Fe410. ISA 80 x 50 x 8 50 115 mm mm 18 mm o hole 35 mm 45 mm
Determine the design tensile strength of plate 150 mm x 12 mm size with holes or 16 mm diameter bolts as shown in figure below. Use Fe410 T 35 14 4 42.5 65 42.5 65 2 3 (All dimensions in mm) 150
What will be the tensile strength due to rupture of critical section of an angle section ISA 150 × 115 x 8, which is connected to gusset plate as shown in figure?. Use Fe410 grade steel. 150 mm 115 mm 8 mm 8 mm 60 mm 150 mm
Situation 12: A single plate 200 mm x 12 mm plate is connected to a steel plate by four 22 mm diameter rivets as shown in the figure. The steel is ASTM A36 with Fy= 248 MPa and Fu = 400 MPa. Use diameter hole = diameter of bolt + 2 Given: y= 40mm, y1 = 120mm, x = 40 mm, x1 = 120mm O 1. Which of the following nearly gives the Allowable Strength Ta in block shear? O 433 KN O 420 KN O 401 KN O 441 KN O O O
The lap connection shown in Figure 3 shows nine 20 mm - diameter A325 bolts spaced as follows: S1 = 50 mm S3 = 50 mm S2 = 80 mm S4= 100 mm Thickness of plates, t= 25 mm Bolt hole diameter = 23 mm Tensile strength and stresses: Yield strength, Fy = 248 MPa Tensile strength of steel, Fu = 400 MPa Allowable tensile stress on gross area = 0.6Fy Allowable tensile stress on net area = 0.5Fu Allowable bolt shear stress= 120 MPa Allowable bolt bearing strength = 480 MPa Calculate the allowable tensile load (kN) based on the following conditions: Based on bearing strength of bolt. 2160 2387 2475 4320Based on shearing strength of bolts. 339 368 415 524Based on tensile strength of plate. 958 1116 1155 1325
Question 4 Complete the table below for the steel sections shown. All sections are bending about their horizontal axis. Section Location hep Ney Slenderness (show calculations) of element bf Flange te ld ++ tw be = 800 mm Web tf = 20 mm d = 1440 mm tw = 16 mm Grade 300, heavily 入。= Whole Asp= Asy= welded plates section br Flange tr d Web bf = 800 mm te = 20 mm d = 1420 mm tw = 16 mm Grade 300, heavily welded plates 入。= Whole Asp= Asy= section
When doing a steel design which diameter would you use, the actual diameter or the designated diameter of 12mm and why.
What is the ultimate strength of an ASTM A36 Steel (Use Appendix G/ Page 501-502) Do not use any external source to answer this question ? Ksi. Your answer should be a numerical value Do not include anything else. Example: If the appendix indicates that the ultimate strength is 88 ksi, your answer should be 88
Determine the design tensile strength of the plate (200 × 100) mm connected to a 12 mm thick gussets, using 20 mm bolts shown below, if the yield and ultimate stress of the steel used are 250 MPa and 420 MPa respectively, fy= 250 MPa fu= 450 MPa
An A36 tension plate is 9 mm thick is given below. Bolts are 20 mm. Given that s = 50 mm and g = 75 mm, calculate the net area at tensile fracture line a-b-f-g in mm2. Write your answer rounded to the nearest whole number. 50 50 + S + S > d a 50 g 50