What type of tool is not used in precision layout? Sine tools Height gage Combination set Vernier bevel protractor
Q: Is the formula dimensionally correct? X= xi + vt2 + 1/2 at
A: Physical quantity depends on three base dimension- Mass [M], Length[L], and Time[T] Given expression…
Q: Express the force as a Cartesian vector Enter the components of the force separated by commas.…
A: Magnetic of forceF = 500 N Given that force component in x-direction make an angle 60 in negative…
Q: A screw gauge advances by 3 mm on main scale in 6 rotations. There are 50 divisions on circular…
A: A screw gauge advances by 3 mm on main scale in 6 rotations. There are 50 divisions on circular…
Q: What is the precision of 0.003000 cm
A: The precision of a measurement refers to the number of significant digits, or the number of digits…
Q: Convert the following: 15.2 in3 to ft3 Express answer with three significant figures
A: Here we are given with 15.2in3 and we have to convert it into ft3
Q: The measurement reading in the figure below is: By V.Ryan 2 3 1 (A) 20.64 mm (B) 19.64 mm 18.46 mm…
A: By observing the given options we will answer the given question.
Q: A block of mass 5.5 kg is suspended from two vertical ropes attached to the ceiling. What is the…
A:
Q: A burette is tested for the accuracy of its measurement. The results for 50 mL measurements are…
A: formula:
Q: QUESTION 27 What is the type of striking tools shown in the figure: KENNEDY Cross pein hammer O Ball…
A: Question 27 A) cross pein hammer Question 28 B) Face Shield
Q: Exercise 2. A schoolbus accelerates for 16 s with 0.9 m/s 2, after that it drives for 50 s with…
A:
Q: Is the formula dimensionally correct? x = x1+vt^2+1/2 at
A: The given formula is x = x1 + vt2 + 1/2 at The dimension of the velocity is given as, Similarly,…
Q: Volume = 35cm²³ dersity = 0.30g cm³ find mass = 3
A:
Q: do you know how to graph this on excel y=-0.0036t^2+0.38t+38.62
A: Given The equation We have to plot this equation.
Q: 3. How many centimeters are in 2.5 yds? 320
A:
Q: By which type of a datum designer determine the reference point, line or surface for dimensioning?…
A: Answer is option 1 By Design We can Determine the reference point ,line or surface dimensioning From…
Q: A systematic error 1. Ois also known as an indeterminate error 2. Ois a measure of the…
A: Error is defined as the difference between actual value & experimental value. It tells us…
Q: The measurement reading in the figure below is: By V.Ryan 2 4 6. (A) 18.46 mm B) 19.64 mm (c) 1.46…
A: In given vernier scale least count is = 0.1 mm Measurement Reading…
Q: Find the average rate of change. 6. 7. 36 30 24 18 12 0 1 2 3 4 5 6 Number of bags of feed used 1 2…
A: We are given with the graph. And we have to convert this graph into the table so that we will have…
Q: 7. Write the correct reading of the micrometer screw gauge given in the figure. mpie 3" mark below 0…
A: Using figure 1 Zero error = -0.03 mm Negative because zero marking is above the datum line
Q: Convert minutes to units in 10-minute increments.
A: To convert minutes into units , 1 hours = 60 minutes . this implies , 1 min…
Q: 1. Make a dimensional analysis of the equations given below and find their units. a) V = 1/2 b) a =…
A: We find out the Dimensional analysis of the equations and their units.
Q: Given si= -10.0 cm and f= -5.00 cm, find so
A:
Q: Is the formula dimensionally correct? vf =(v1 + v2)/2
A: The unit of the velocity is m/s, therefore the dimensional formula of the velocity is [LT-1]. Here…
Q: Find the volume of a pyramid has a height of 481 ft and the base area covers 13.0 acres
A:
Q: Determine the Cross-sectional Area and Volume of Cylindrical Object Measure diameter with a…
A: Given that, the pitch scale reading is P.S.R=12mm Circular scale reading is C.S.R=22 Least count is…
Q: complete the table by filling out the last two columns and what do the results in the last two…
A:
Q: Suppose we measure the length of a table to be Xa= 59.7 inches,but the true value is Xa = 59.5…
A:
Q: HELLO HELP WITH NUMBER 3 PLEASE, COMPLETE SOLUTION, 4 DECIMAL PLACES. THANK YOUUU Given the…
A: When an object is hanging by a string and its one end is fixed with, then if that object is free to…
Q: QUESTION 12 Protractor is used for Angular mesurement True False QUESTION 13 Pallet hammers are used…
A: Protractor is used to measure plane angles. Answer: Yes
Q: The graduated cylinder was found to an average of 9.765+ or -0.170 mL in measuring 10 mL portions…
A: Given: The average volume measured is 9.765±0.170 mL. Introduction: Percent error is the difference…
Q: Complete the table stating the associated error values and their units for each instrument.…
A: Meter rule has 1mm least count vernier calliper has 0.1 mm least count screw gauge has 0.01 mm least…
Q: Find the value of m. Megabytes 72 108 0 1 Seconds 4 9.
A: case 1) megabytes/sec = 72/4 = 18 Mb/s Case 2) Megabytes/sec = 108/6 = 18 Mb/s Therefore, for t =…
Q: (b) v = vo + at² Vo t
A:
Q: Usually how many types of errors are present in scientific measurements? a) 2 b) 3 c) 4 d) 5
A: To find: Usually how many types of errors are present in scientific measurements
Q: In the figure below, what is the ratio Ibat/l1? 2R Ibat
A:
Q: Q1 : Check the correctness of the following formulae by dimensional analysis. F = mv² /r
A: Given:centripetal force.F=mv2rNow ,Using dimensional analysis.where,The mass =m=MThe…
Q: Table 2 Graphic Averaging Method Riser Block Thickness T= 1 in. = 2.54 x 10 m Distance between…
A: Given : Given two tables to calculate the acceleration due to gravity using 1) Calculational…
Q: Usually, what is the least count of a screw gauge? a) 0.01 cm b) 0.001 cm c) 0.1 cm d) 1 mm
A: To find: Usually, what is the least count of a screw gauge
Step by step
Solved in 2 steps