What is the weight of a steel I-beam 40 feet long with a cross-sectional area of 42 in2? Steel density is 0.283 lb/in3 .   Be careful of the units. Round to the nearest whole pound.

Q: If a 2-meter wooden column is under tension and it extends 4 mm when load is applied, the strain is…

A: Given Data Length of the column (L) = 2m = 2000 mm  Change in length (∆L) = 4 mm  Determined the…

Q: Please refer to the figure shown below. If P is equal to 6,720 lb., and if all the rods have a…

A:

Q: What is the mass of stainless steel if the volume is 160 cm3?

A: Given data :- In question given that material is stainless steel and the volume of that material is…

Q: A steel weighing 490 lb/cu. has an ultimate strength of 80000 psi. what is the maximum length of the…

A:

Q: me design strength (Mu) of the T-beam sh

A: f'(c) =27 MPa, fy = 350 MPaNeed to findDesign strength of beam

Q: Determine the maximum safe tensile force that can be supported by a 12 mm by 150 mm plate if its…

A:

Q: TIT 77

A: Mass of block  is 400 lb .

Q: The compound bar containing steel bronze and aluminum segments carries the axial loads shown in the…

A:

Q: 4P Steel Bronze Aluminum

A: Given:- P=8200 lbArea of cross section=0.4 in2Allowable stress in steel=120 MPaAllowable stress in…

Q: How many forces are acting in X Direction? Hint: Draw FBD and break forces into Components B 30% FAE…

A:

Q: If an aluminum weighs 165 lb/ft^3, How much will a 12-in dia. sphere weigh when immersed in water?

A:

Q: 13/13 FOR THE RIGID BEAM SHOWN BELOW FIND THE STRESS IN ALUMNUM ROD Steel Rod Est= 200 kN/mm A…

A:

Q: How we can calculate the weight of 12m long and 10mm dia. Steel on-site?

A: The given data is: Length, L=12 m Diameter, D=10 mm

Q: What is the weight (N) of a cube of stainless steel with 8 cm on each edge?

A: Each edge of cube is 8cm = 0.08m Volume of cube = 0.08x0.08x0.08 = 0.000512m3 The density of steel =…

Q: Consider the manner in which a rectangular bar deforms elastically when the bar is subjected to the…

A: Consider a rectangular bar of length ‘l’ and subjected to a tensile force. If the force is tensile…

Q: A structural of 200 mm long must be able to support a load of 100,000 N without experiencing any…

A: First we summarise the given data : Note - Density in Kg/m3

Q: What is the axial stress in a structural member with cross-section area 10 in2 subjected to a…

A: Solution: Given: Area (A)=10in2 Tension Load (F)=1000lb

Q: A steel plate is 300 mm wide and 10 mm thick. A rivet of nominal diameter of 16 mm is driven into…

A: Diameter of the hole =do+1.5    (do≤25mm)d=16+1.5=17.5mm

Q: If an A36 steel rod under tension load has a strain gage that measures 0.003 in/in, what is the…

A: Given:- The steel rod under tension load = A36 The strain measured by strain gage = 0.003 in/in To…

Q: A compressive load of 50 KN is applied 150 on the axis of a steel-round bar of 8 mm diameter.…

A: Given,  Compressive Load, F= 50 kN Diameter of the steel-round bar= 8mm Modulus of Elasticity= 75…

Q: For the given simply supported beam the height of the beam is fixed by other design considerations,…

A: Let b is the width of aluminium beam b1 is the width ofsteel beamHeight of the beam=hSpan of the…

Q: A brass bar, having square cross-section of side 50 mm, is subjected to axial forces as shown in…

A: Material: Brass barCross-section: SquareSide of square: 50 mm (Note: This translates to an area of…

Q: An SAE3140 OQT 1300 steel bar with a rectangular cross section of  2 in ( base) by 3.5 in (height)…

A: From table Design Properties of Carbon and Alloy Steels (appendix 3 )   For SAE3140 OQT 1300…

Q: qualitatively sketch the deformed shape of the beam for the given loads

A:

Q: A tensile load of 75,000 lb is applied to a metal bar with a 0.8 in. x 0.8 in. cross-section and a…

A:

Q: Problem 6.110 The wood used for the box beam has an allowable bending stress of 6.7 MPa. (Figure 1)…

A: Given :

Q: The composite plate is made from both steel (A) and brass (B) segments. Take pst = 7.85 Mg/m³ and…

A:

Q: A structural of 200 mm long must be able to support a load of 100,000 N without experiencing any…

A:

Q: What is the flexural stress of a bar of chocolate that has a width of 50mm, a thickness of 0.0o09m,…

A: What is the flexural stress of a bar of chocolate?

Q: A compressive load of 50 KN is applied 15 degrees on the axis of a steel-round bar of 8 mm diameter.…

A: Stress:  Resisting force acting per unit area is known as Stress. Its unit is N/mm2 Strain:  Ratio…

Q: Elastic Modulus of the bar?

A:

Q: How much will a steel rod lengthen under tension with the following considerations? The steel rod is…

A:

Q: b. If the bar stretches 0.002 in., d naterial has lin ear-elastic behavi

A: WE KNOWMod of elasticity :E =StressAxial StrainAxial…

Q: Please give me three answers clearly.. thank you What is the stifness of a bar in tension and…

A: We are authorized to answer one question at a time, since you have not mentioned which part you are…

Q: ine the elastic section modulus (Sx) and plastic sect ng steel sections. Express your answer in in°.…

A: Given : Unsymmetrical I section and hollow rectangular section are given. Plastic and elastic…

Q: How does the slope of the unload/reload line correspond to the Modulus of Elasticity calculated from…

A:

Q: What standard diameter deformed bar used as stirrups for beam? 10 mm diameter O 8 mm diameter O 6 mm…

A: Stirrups are rectangular loops built from a plain round bar that contain or restrain the primary…

Q: Problem 6.110 The wood used for the box beam has an allowable bending stress of 6.7 MPa. (Figure 1)…

A:

Q: 20 mm diameter rod having a gauge length of 110 mm and yield strength of 160 mpa, was subjected to a…

A:

Q: A cylindrical piece of steel of 80 mm diameter and 120 mm long is subjected to an axial compressive…

A:

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?